YP250 Service Manual

FOREWORD
This Supplementary Service Manual has been prepared to introduce new service and data for the
YP250. For complete service information procedures it is necessary to use this Supplementary Ser-
vice Manual together with the following manual.
YP250 SERVICE MANUAL: 4UC-AE1

YP250 (K) ’98 SUPPLEMENTARY SERVICE MANUAL: 4UC-AE2
YP250D ’98 SUPPLEMENTARY SERVICE MANUAL: 5DF-AE1
YP250 2000
SUPPLEMENTARY
SERVICE MANUAL
1999 by Yamaha Motor Co., Ltd.
1999 by MBK Industrie
First Edition, November 1999
Any reproduction or unauthorized use
without the written permission of
Yamaha Motor Co., Ltd.
is expressly prohibited.
EB001000
NOTICE
This manual was produced by the Yamaha Motor Company primarily for use by Yamaha/MBK dealers
and their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one manu-
al, so it is assumed that anyone who uses this book to perform maintenance and repairs on Yama-
ha/MBK scooter has a basic understanding of the mechanical ideas and the procedures of scooter
repair. Repairs attempted by anyone without this knowledge are likely to render the scooter unsafe and
unfit for use.
Yamaha Motor Company, Ltd. is continually striving to improve all its models. Modifications and signifi-
cant changes in specifications or procedures will be forwarded to all authorized Yamaha/MBK dealers
and will appear in future editions of this manual where applicable.
NOTE:
Designs and specifications are subject to change without notice.
IMPORTANT INFORMATION
Particularly important information is distinguished in this manual by the following notations.
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR

SAFETY IS INVOLVED!
WARNING Failure to follow WARNING instructions could result in severe injury or death to
the scooter operator, a bystander or a person inspecting or repairing the scoot-
er.
CAUTION: A CAUTION indicates special precautions that must be taken to avoid damage
to the scooter.
NOTE: A NOTE provides key information to make procedures easier or clearer.

YP002000
HOW TO USE THIS MANUAL

MANUAL ORGANIZATION
This manual consists of chapters for the main categories of subjects. (See “Illustrated symbols”)
1st title 1 : This is the title of the chapter with its symbol on the upper right corner of each page.
2nd title 2 : This title indicates the section of the chapter and only appears on the first page of each
section. It is located in the upper left corner of the page.
3rd title 3 : This title indicates a sub-section that is followed by step-by-step procedures accompa-
nied by corresponding illustrations.
EXPLODED DIAGRAMS
To heps identify parts and clarify procedure steps, there are exploded diagrams at start of each remov-
al and disassembly section.
1. An easy-to-see exploded diagram 4 is provided for disassembly and assembly jobs.
2. Numbers 5 are given in the order of jobs in the exploded diagram. A number that is enclosed by a
circle indicates a disassembly step.
3. An explanation of jobs and notes is presented in an easy-to-read way by the use of symbol marks
6 . The meanings of the symbol marks are given on the next page.
4. A job instruction chart 7 accompanies the exploded diagram, providing the order of jobs, names
of parts, notes in jobs, etc.
5. For jobs requiring more information, the step-by-step format supplements 8 are given in addition
to the exploded diagram and the job instruction chart.
2 1 4 3
5
8
6
6
7
EB003000
1 2
ILLUSTRATED SYMBOLS
GEN Illustrated symbols 1 to 9 are designed as
SPEC thumb tabs to indicate the chapter’s number
INFO and content.
3 4 1 General information
INSP 2 Specifications
ADJ ENG 3 Periodic inspection and adjustment

4 Engine
5 Cooling system
5 6
6 Carburetion
7 Chassis
COOL CARB 8 Electrical
9 Troubleshooting
7 8
CHAS ELEC
Illustrated symbols 10 to 17 are used to identify
9 10
the specifications appearing in the text.
TRBL 10 Possible to maintain with engine mounted
SHTG 11 Filling fluid
12 Lubricant
11 12 13 Special tool
14 Tightening
15 Wear limit, clearance
16 Engine speed
17 Ω, V, A
13 14
15 16 17
Illustrated symbols 18 to 23 in the exploded dia-
grams indicate the types of lubricants and lu-
brication points.
18 Apply engine oil
18 19 20
19 Apply gear oil
20 Apply molybdenum disulfide oil
21 Apply wheel bearing grease
22 Apply lightweight lithium-soap base grease
21 22 23 23 Apply molybdenum disulfide grease
Illustrated symbols 24 to 25 in the exploded dia-
grams indicate the where to apply locking agent
24 and when to install new parts 25 .
24 25 24 Apply locking agent (LOCTITE)

25 Use new one
CONTENTS
GENERAL INFORMATION
SCOOTER IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
VEHICLE IDENTIFICATION NUMBER (for E) . . . . . . . . . . . . . . . 1
FRAME SERIAL NUMBER (except for E) . . . . . . . . . . . . . . . . . . . 1
ENGINE SERIAL NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MODEL LABEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SPECIAL TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SPECIFICATIONS
GENERAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
MAINTENANCE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TIGHTNING TORQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TIGHTNING TORQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ELECTRICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
LUBRICATION POINTS AND GRADE OF LUBRICANT . . . . . . . . . 15
ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CABLE ROUTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PERIODIC INSPECTIONS AND ADJUSTMENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PERIODIC MAINTENANCE/LUBRICATION INTERVALS . . . . . . . . 26
COVER AND PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SIDE COVER, SIDE COVER MOLE PASSENGER SEAT . . . . . 28
RIDER SEAT AND MAIN BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SIDE COVER MOLE AND FOOTREST BOARD . . . . . . . . . . . . . 31
COWLING, HANDLE COVER, METER ASSEMBLY . . . . . . . . . . 32
LEGSHIELD AND FUEL TANK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ENGINE OIL REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
CRANKCASE FILTER CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . 35
AIR INDUCTION SYSTEM INSPECTION . . . . . . . . . . . . . . . . . . . 36
COOLANT REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
ELECTRICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
HEADLIGHT BEAM ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . 40
ENGIVE OVERHAUL
ENGINE REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
WIREHARNESS, CABLE AND REAR BRAKE . . . . . . . . . . . . . . . 41
HOSES, AIR FILTER CASE, ENGINE MOUNTING BOLT AND
ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
CYLINDER HEAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
V BELT, CLUTCH AND SECONDARY/PRIMARY SHEAVE . . . . . . 46
CRANKCASE FILTER COVER AND CRANKCASE COVER
(LEFT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
V BELT, CLUTCH AND SECONDARY/PRIMARY SHEAVE . . . . 47
TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
AIR INDUCTION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
CRANKCASE AND CRANKSHAFT . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
CRANKCASE REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
CRANKSHAFT REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
CRANKSHAFT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
COOLING SYSTEM
RADIATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
CARBURETOR
CARBURETOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
CARBURETOR DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
THROTTLE POSITION SENSOR ADJUSTMENT . . . . . . . . . . . . 58
CHASSIS
FRONT WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
SPEED SENSOR AND SENSOR ROTOR . . . . . . . . . . . . . . . . . . 59
SPEED SENSOR AND THE SENSOR ROTOR . . . . . . . . . . . . . . 60
SPEED SENSOR REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
SPEED SENSOR AND SENSOR ROTOR INSPECTION . . . . . 60
SPEED SENSOR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
REAR WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
REAR SHOCK ABSORBER AND SWINGARM . . . . . . . . . . . . . . . . . 65
ELECTRICAL
ELECTRICAL COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
CHECKING SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
SWITCH POSITION AND TERMINAL CONNECTION . . . . . . . . 69
CHECKING STEPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
SWITCH CONNECTION AS SHOWN IN THIS MANUAL . . . . . . 70
IGNITION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
ELECTRIC STARTING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
LIGHTING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
SIGNAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
SIGNAL SYSTEM CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
FUEL PUMP SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
CIRCUT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
FUEL PUMP CIRCUIT OPERATION . . . . . . . . . . . . . . . . . . . . . . . 90
CHECKING THE FUEL PUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
WIRING DIAGRAM
GEN
SCOOTER IDENTIFICATION INFO
YP100000
GENERAL INFORMATION
SCOOTER IDENTIFICATION
YP100010
VEHICLE IDENTIFICATION NUMBER (for E)

The vehicle identification number 1 is stamped
into the right side of the frame.
NOTE:
The vehicle identification number is used to
identify your scooter and may be used to regis-
ter your scooter with the licensing authority in
your country.
YP100020
FRAME SERIAL NUMBER (except for E)

The frame serial number 1 is stamped into the
right side of the frame.
EB100030
ENGINE SERIAL NUMBER

The engine serial number is stamped into the
crankcase.
NOTE:
Designs and specifications are subject to
change without notice.
MODEL LABEL
The model label is affixed under the seat.
This information will be needed to order spare
parts.
1
GEN
SPECIAL TOOLS INFO
EB102000
SPECIAL TOOLS
The following special tools are necessary for complete and accurate tune-up and assembly.
Use only the appropriate special tools; this will help prevent damage caused by the use of inappropri-
ate tools or improvised techniques.
When placing an order, refer to the list provided below to avoid any mistakes.
Tool No. Tool name/Usage Illustration

Crankcase separating tool
90890-01135
This tool is used to remove the crankshaft.

Installer pot Crankshaft installer pot/bolt/adapter/spacer
90890-01274
Bolt
90890-01275
Adaptor
90890-01280
90890-01478
Spacer
90890-01016
90890-01288 These tools are used to install the crankshaft.
2
GENERAL SPECIFICATIONS SPEC
SPECIFICATIONS
GENERAL SPECIFICATIONS
Model YP250
Model code: 5GM2, 5GM3
Dimensions:
Overall length 2,140 mm
Overall width ,780 mm
Overall height 1,350 mm
Seat height ,730 mm
Wheelbase 1,535 mm
Minimum ground clearance ,120 mm
Minimum turning radius 2,700 mm
Basic weight:
With oil and full fuel tank 168 kg
Engine:
Engine type Liquid-cooled 4-stroke, SOHC
Cylinder arrangement Forward-inclined single cylinder
Displacement 0.249L (249 cm3)
Bore stroke 69.0 66.8 mm
Compression ratio 10 : 1
Compression pressure (STD) 1,400 kPa (14 kg/cm2, 14 bar) at 500 r/min
Starting system Electric starter
Lubrication system: Wet sump
Oil type or grade:
Engine oil
API STANDERD:
SE or higher grade
Periodic oil change 1.2 L

Total amount 1.4 L
Transmission oil
Total amount 0.25 L
Radiator capacity:
Total amount (including all routes) 1.4 L
Air filter:
Carburetor side Wet type element
Crankcase side Dry type element
Fuel:
Type Regular unleaded gasoline
Fuel tank capacity 12 L
3
Model YP250
Carburetor:
Type/quantity Y28V-1E/1
Manufacturer TEIKEI
Spark plug:
Type DR8EA
Manufacturer NGK
Spark plug gap 0.6 X 0.7 mm
Clutch type: Dry, centrifugal automatic
Transmission:
Primary reduction system Helical gear
Primary reduction ratio 40/15 (2.666)
Secondary reduction system Helical gear
Secondary reduction ratio 38/15 (2.533)
Transmission type Single speed automatic (V-belt type)
Operation Centrifugal automatic type
Single speed automatic 2.44 X 0.83:1
Chassis:
Frame type Steel tube underbone
Caster angle 28
Trail 103 mm
Tire:
Type Tubeless
Size front 110/90-12 64L
rear 130/70-12 62L
Manufacturer front IRC/MICHELN
rear IRC/MICHELN
Type front MB67/BOPPER
rear MB67/BOPPER
Tire pressure (cold tire):
Maximum load-except motorcycle 187 kg
Loading condition A* 0 X 90 kg
front 175 kPa (1.75 kg/cm2, 1.75 bar)
rear 200 kPa (2.0 kg/cm2, 2.0 bar)
Loading condition B* 90 X 205 kg
rear 225 kPa (2.25 kg/cm2, 2.25 bar)
High-speed riding
rear 225 kPa (2.25 kg/cm2, 2.25 bar)
*Load is the total weight of cargo, rider, passenger, and accessories.
4
Model YP250
Brake:
Front brake type Single disc brake
operation Right hand operation
Rear brake type Single disc brake
operation Left hand operation
Suspension:
Front suspension Telescopic fork
Rear suspension Unit swing
Shock absorber:
Front shock absorber Coil spring/Oil damper
Rear shock absorber Coil spring/Oil damper
Wheel travel:
Front wheel travel 100 mm
Rear wheel travel 90 mm
Electrical:
Ignition system T.C.I. (Digital)
Generator system A.C. magneto
Battery type GT7B-4
Battery capacity 12 V 6.5 AH
Headlight type: Quartz bulb (Halogen)
Bulb wattage quantity:
Headlight (High) 12 V 60 W/55 W 1
Headlight (Low) 12 V 55 W 1
Auxiliary light 12 V 5 W 1
Tail/brake light 12 V 5 W/21 W 2
Flasher light (Front) 12 V 21 W 2
Flasher light (Rear) 12 V 16 W 2
Meter light 12 V 1.7 W 3
High beam indicator light 12 V 1.7 W 1
Oil indicator light 12 V 1.7 W 1
Turn indicator light 12 V 3.4 W 2
License light 12 V 5 W 1
5
MAINTENANCE SPECIFICATIONS SPEC
MAINTENANCE SPECIFICATIONS
ENGINE
Item Standard Limit

Cylinder head:
Warp limit 0.05 mm
Cam chain:
Cam chain type/No. of links DID SCA-0404A SDH/104
Cam chain adjustment method Automatic
Automatic centrifugal clutch:
Clutch shoe thickness 3.3 mm 2.0 mm
Clutch housing inside diameter 135 mm 135.5 mm
Clutch shoe spring free length 28.1 mm
Weight outside diameter 20 mm 19.5 mm
Clutch – in revolution 2,250 2,850 r/min
Clutch – stall revolution 3,700 4,700 r/min
V-belt:
V-belt width 22.6 mm 21.0 mm
Carburetor:
Type Y28V-1E/1
I.D. mark 5GM 10
Ventuly outside diameter ø28
Main jet (M.J) #128
Main air jet (M.A.J) ø0.9
Jet needle (J.N) 5D9B-3/5
Throttle valve size (Th.V) 11
Pilot air jet (P.A.J.1) ø1.2
Needle jet (N.J) #85
Pilot outlet (P.O) ø0.8
Pilot jet (P.J) #43
Bypass (B.P) 0.7 3
1
Pilot screw (P.S) 2 2
Valve seat size (V.S) 1.4
Starter jet 1 (G.S.1) ø0.5
Starter jet 2 (G.S.2) ø0.5
Float height (F.H) 26.5 27.5 mm
Engine idle speed 1,300 1,500 r/min
Intake vacuum 29.3 36.0 kPa (220 270 mmHg)
Oil temperature 65 75C
Cooling water temperature 80C
Fuel pump:
Type Electrical
Model/manufacturer 2GV/MITSUBISHI
6
Item Standard Limit

Radiator:
Type Cooling fin with electric fan
Width/height/thickness 140/238/24 mm
Radiator cap opening pressure 110 140 kPa (1.1 1.4 kg/cm2,
1.1 1.4 bar)
Radiator capacity 1.4 L
Reservoir tank capacity 0.4 L
7
TIGHTENING TORQUES
ENGINE
Tightening
Thread torque
Part to be tightened
g Part name Q’ty
y Remarks
size
Nm mkg
Oil check bolt — M6 1 7 0.7
Exhaust pipe stud bolt — M8 2 13 1.3
Air induction system pipe stud bolt — M6 2 10 1.0
Spark plug — M12 1 18 1.8
Cam sprocket cover Bolt M6 2 10 1.0
Cylinder head and cylinder Nut M8 4 22 2.2
Cylinder head and cylinder Bolt M6 2 10 1.0
(Cam chain side)
Valve cover Bolt M6 5 10 1.0
Rotor Nut M16 1 80 8.0
Valve adjuster locknut Nut M6 2 14 1.4
Cam shaft bearing stopper Bolt M6 2 8 0.8
Cam sprocket Bolt M10 1 60 6.0
Cam chain tensioner
(Body) Bolt M6 2 10 1.0
(Plug) Bolt M8 1 8 0.8
Guide stopper 2 Bolt M6 1 10 1.0
Water pump housing cover Bolt M6 3 10 1.0
Hose joint — M6 2 7 0.7
Thermostatic valve cover Bolt M6 2 10 1.0
Filler neck supporting Bolt M5 1 5 0.5
Oil pump Screw M6 2 7 0.7
Oil pump cover Bolt M3 1 1 0.1
Oil strainer cover Bolt M35 1 32 3.2
Carburetor joint Bolt M6 2 10 1.0
Carburetor joint and carburetor Nut M6 2 10 1.0
Air filter assembly Bolt M6 2 7 0.7
Air filter cover Screw M5 7 1 0.1
Exhaust pipe assembly Nut M8 2 20 2.0
Muffler Bolt M10 3 53 5.3
Muffler and exhaust pipe Bolt M8 1 14 1.4
Protector (Exhaust pipe) Screw M6 2 10 1.0
Protector (Muffler end cap) Screw M6 3 10 1.0
Air induction system pipe Nut M6 2 12 1.2
Air induction system assembly Bolt M6 2 10 1.0
Air induction system air filter assembly Bolt M6 2 7 0.7
Crankcase (left and right) Bolt M6 9 10 1.0
Drain bolt (Engine oil) Bolt M12 1 20 2.0
Drain bolt (Transmission oil) Bolt M8 1 22 2.2
Oil filler Bolt M14 1 3 0.3
Transmission case cover Bolt M8 6 16 1.6
Crankcase cover (left) Bolt M6 8 10 1.0
Crankcase filter cover — M5 3 1.2 0.12
Crankcase cover protector Bolt M6 1 7 0.7
Crankcase cover protector Screw M6 3 7 0.7
Magnet cover — M6 10 10 1.0
8
Tightening
Thread torque
g Part name Q’ty
y Remarks
size
Nm mkg
Cover (oil pump) Bolt M6 2 12 1.2
Timing check plug Plug M16 1 8 0.8
One way clutch — M8 3 30 3.0
Clutch housing Bolt M14 1 60 6.0
Grease stopper (Primary sheave) — M4 4 3 0.3
Primary fixed sheave — M14 1 80 8.0
Clutch carrier assembly — M36 1 90 9.0
Stator — M6 3 10 1.0
Pick up coil — M5 2 7 0.7
Starter motor Bolt M6 2 10 1.0
Thermo switch — M18 2 23 2.3
Thermo unit — Pt 1/8 1 8 0.8
9
CHASSIS
Item Standard Limit

Front suspension:
Front fork travel 100 mm
Fork spring free length 268 mm 263 mm
Spring rate (K1) 4.82 N/mm (0.49 kg/mm)
Stroke (K1) 0 40 mm
Stroke (K2) 40 100 mm
Oil capacity 0.142 L (142 cm3)
Oil level 80 mm
Oil grade Fork oil 15 WT or equivalent
Inner tube vend limit 0.2 mm
Rear suspension:
Shock absorber stroke 106 mm
Spring free length 262 mm 257 mm
(K2) 14 N/mm (1.43 kg/mm)
(K3) 26.39 N/mm (2.69 kg/mm)
Stroke (K1) 0 40 mm
(K2) 40 70 mm
(K3) 70 106 mm
Rear disk brake:
Type Single
Disc outside diameter thickness 230 5 mm
Pad thickness 5.3 mm 0.8 mm
Master cylinder inside diameter 11 mm
Caliper cylinder outside diameter 22.2 mm 2
Brake fluid type DOT #4
Brake lever:
Brake lever free play (front at lever 2 5 mm
side)
Brake lever free play (rear) 2 5 mm
Throttle cable free play 3 5 mm
10
TIGHTENING TORQUES
CHASSIS
Tightening
g Thread size torque Remarks
Nm mkg
Frame and engine bracket M12 1.25 59 5.9
Engine bracket, compression rod and engine M10 1.25 32 3.2
Compression rod and frame M10 1.25 64 6.4
Sidestand (bolt and frame) M10 1.25 40 4.0
Sidestand (bolt and nut) M10 1.25 40 4.0
Rear footrest bracket M 6 1.0 7 0.7
Swingarm M 8 1.25 35 3.5
Rear shock absorber and frame M10 1.25 40 4.0
Rear shock absorber and engine M 8 1.25 20 2.0
Steering ring nut M25 1.0 22 2.2 See “NOTE”
Handle holder and steering shaft M20 1.5 155 15.5
Handle upper holder and lower holder M 8 1.25 23 2.3
Brake hose and master cylinder M10 1.25 30 3.0
Fuel tank
(font) M 6 1.0 10 1.0
(rear) M 6 1.0 7 0.7
Fuel sender M 5 0.8 3 0.3
Filter M 6 1.0 7 0.7
Roll over valve M 5 0.8 4 0.4
Box M 6 1.0 10 1.0
Box (Bracket) M 8 1.25 16 1.6
Standing handle M 8 1.0 16 1.6
Sheet lock assembly M 6 1.0 10 1.0
Plastic parts & cover M 5 1.0 2 0.2
Cowling stay M 8 1.25 16 1.6
Cowling body M 6 1.0 7 0.7
Footrest board M 6 1.0 7 0.7
Headlight assembly M 6 1.0 7 0.7
Tail light assembly M 6 1.0 7 0.7
Front wheel axle and nut M14 1.5 70 7.0
Rear wheel axle and nut M14 1.5 135 13.5
Front brake caliper and front fork M10 1.25 50 5.0
Brake disc and hub M 8 1.25 23 2.3
Brake hose and caliper M10 1.25 30 3.0
Brake caliper and bleed screw M 7 1.0 6 0.6
Rear brake caliper and swingarm M10 1.25 40 4.0
Speed sensor and sensor housing M 8 1.25 23 2.3
Windscreen M 5 1.0 0.4 0.04
11
NOTE:
1. First, tighten the ring nut (lower) approximately 38 Nm (3.8 mkg) by using the torque wrench, then
loosen the ring nut 1/4 turn.
2. Second, tighten the ring nut (lower) approximately 22 Nm (2.2 mkg) by using the torque wrench,
then finger tighten the ring nut (center). Align the slots both ring nut and install the lock washer.
3. Final, hold the ring nuts (lower and center) and tighten the ring nut (upper) 75 Nm (7.5 mkg) by
using the torque wrench.
12
ELECTRICAL
Item Standard limit

Ignition timing:
Ignition timing (B.T.D.C.) 10_ at 1,400 r/min :::
Advanced timing (B.T.D.C.) 32_ at 5,000 r/min :::
Advanced type Electrical type :::
T.C.I.:
Pickup coil resistance/color 189 231 Ω at 20_C/ :::
Yellow – Blue :::
T.C.I. unit model/manufacturer J4T117/MITSUBISHI :::
Ignition coil:
Model/manufacturer F6T507 /MITSUBISHI :::
Minimum spark gap 6 mm :::
Primary winding resistance 3.6 4.8 Ω at 20_C :::
Secondary winding resistance 10.7 14.5 kΩ at 20_C :::
Spark plug cap:
Type Resin type :::
Resistance 10 kΩ :::
Charging system:
Type A.C. magneto :::
Model/manufacturer F4T370 /MITSUBISHI :::
Normal output 14 V 19.5 A at 5,000 r/min :::
Stator coil resistance/color 0.37 0.45 Ω at 20_C/ :::
White – White :::
Rectifire/regulator:
Model/manufacturer SH640A-12/SHINDENGEN :::
No load regulated voltage 14.1 14.9 V :::
Capacity 18 A :::
Withstand voltage 200 V :::
Electric starter system:
Type Constant mesh type :::
Starter motor:
Model/manufacturer /ID number SM-13/MITSUBA/SM-13454 :::
Operation voltage 12 V :::
Output 0.65 kW :::
Armature coil resistance 0.0017 0.0027 Ω at 20_C :::
Brush overall length 10 mm 4 mm
Brash quantity 2 pcs. :::
Spring force 8.82 N (899 g) 570 g
Commutator diameter 28 mm 27 mm
Mica undercut (depth) 0.7 mm :::
13
Item Standard limit

Starter relay:
Model/manufacturer MS5F-421 /JIDECO :::
Amperage rating 180 A :::
Coil winding resistance 4.2 X 4.6 Ω at 20_C :::
Horn:
Model/manufacturer YF-12/NIKKO :::
Maximum amperage 3A :::
Flasher/hazard relay
Type Full transistor type :::
Model/manufacturer FE246BH/DENSO :::
Flasher frequency 75 X 95 cycle/min :::
Fuel gage:
Model/manufacturer 5GM/NIPPON SEIKI :::
Sender unit resistance – full 4 X 10 Ω :::
Sender unit resistance – empty 90 X 100 Ω :::
Starting circuit cut-off relay:
Model/manufacturer ACA12115-1/MATSUSHITA :::
Coil winding resistance 72 X 88 Ω :::
Electric fan motor:
Model/manufacturer 5GM/MITSUBA :::
Thermo switch (electric fan):
Model/manufacturer 5GH/NIHON THERMOSTAT :::
Thermo switch (auto choke):
Model/manufacturer 5GM/NIHON THERMOSTAT :::
Thermo unit:
Model/manufacturer 46X/NIPPON SEIKI :::
Circuit breaker:
Type Fuse :::
MAIN 30 A 1 pc. :::
HEAD LIGHT 15 A 1 pc. :::
SIGNALING SYSTEM 15 A 1 pc. :::
IGNITION 7.5 A 1 pc. :::
RADIATOR 4A 1 pc. :::
BACK UP 10 A 1 pc. :::
Reserve 30 A 1 pc. :::
Reserve 7.5 A 1 pc. :::
14
LUBRICATION POINTS AND GRADE OF LUBRICANT SPEC
LUBRICATION POINTS AND GRADE OF LUBRICANT

ENGINE
Lubrication Point Symbol

Oil seal lips
O-ring (Except V-belt drive unit)
Cylinder head tightening nut mounting surface
Crankshaft pin outside
Connecting rod big end thrust surface
Rotary filter inner surface
Drive gear inner surface
Cam chain outside sprocket inner surface
Piston pin
Piston outside and ring groove
Camshaft cam profile
Valve stem (IN, EX)
Valve stem end (lN, EX)
Rocker shaft
Valve rocker arm inner surface
Shaft
Shaft (Oil pump assembly)
Gasket (Oil pump assembly)
Holder
Idle gear 1 thrust surfaces
Shaft 1
Idle gear 2 thrust surfaces
Idle gear 2 inner surface
Main axle thrust surfaces
Crankcase mating surfaces Yamaha bond No. 1215
Crankcase breather plug
Stator grommet Yamaha bond No. 1215
Suction pipe
15
LUBRICATION POINT AND GRADE OF LUBRICANT SPEC
CHASSIS
Lubrication Point Symbol

Front wheel oil seal lips (left/right)
Swingarm oil seal lips (left/right)
Steering head pipe bearing (upper/lower)
Steering head pipe dust seal lips (upper/lower)
Tube guide (throttle grip) inner surface
Brake lever and lever holder bolt sliding surface
Sidestand sliding surface
Centerstand sliding surface and mounting bolt
Centerstand stopper pivot shaft
16
CABLE ROUTING SPEC
CABLE ROUTING
1 Speed sensor 15 Frame A Route the brake hose assembly
2 Front brake hose 16 Seat lock cable through the guide on the handle-
3 Throttle cable 17 Footrest board bar.
4 Relay 18 Handlebar B Fasten the front brake hose,
5 Brake hose assembly 19 Handlebar under cover brake hose assembly throttle
6 Thermo switch lead 20 Handlebar upper cover cable to the frame with a plastic
7 Fan motor lead 21 Right handlebar switch lead band.
8 Switch assembly 22 Front brake switch lead C Fasten the brake hose assembly,
9 Carburetor fuel drain hose 23 Left handlebar switch lead throttle cable to the frame with a
10 Carburetor coolant drain hose 24 Rear brake switch lead band and the end of band is
11 Carburetor air ventilation hose backward.
12 Coolant pipe
13 Sidestand switch
14 Ignitor unit
17
CABLE ROUTING SPEC
D Clamp the brake hose assembly. I Throttle cable pull side. (White P Fasten the wire harness to the
E Fasten the seat lock cable nut) frame with a band and the end of
throttle cable and wireharness to J Throttle cable push side. (Black band inside.
the frame with a band, and the and white nut) Q Roll the tape because of fix the
end of band is downward. K Clamp the fuel hose. protection tube to the fuel pum
F Clamp the switch assembly lead L Route the carburetor coolant lead.
with a band and cut the end of drain hose, carburetor fuel drain R Clamp the fuel pump lead and
band. It’s downward. hose through the clamp. sidestand switch lead.
G Fasten the throttle cable with a M Route the carburetor drain hose S Fasten the throttle cable and the
band and more than 10 mm through the centerstand spring end of band backward.
between throttle cable and box. hook. T Lubricate the silicone grease
H Don’t scrub each other when fix N Clamp the sidestand switch befor fasten the cable and
the throttle cables. lead. hoses.
O Touch the protection tube on the
fuel pump.
18
CABLE ROUTING SPEC
U More than 10 mm. A’ Fasten the left handlebar switch
V Route the seat lock cable lead and rear brake switch lead
through the footrest board. to the handlebar with a plastic
W Route the left handlebar switch locking tie, cut the end of locking
lead through front side of the tie at 5 mm or less.
handlebar under cover. B’ Don’t catch the seat lock cable
X Route the right handlebar switch between footrest board and box.
lead through the clamp.
Y Route the front brake hose
through the right hole of handle-
bar under cover.
Z Route the brake hose assembly
through the left hole of the han-
dlebar under cover.
19
CABLE ROUTING SPEC
1 Box light 13 Engine bracket D Fasten the wireharness to the
2 Rectifire/ regulator 14 Rear brake hose frame with a plastic locking tie.
3 Air induction system air filter 15 A. C. magneto lead E Clamp the rear brake hose.
4 Wireharness 16 Starter motor lead F Clamp the wireharness to the
5 Battery negative lead frame with a plastic locking tie.
6 Battery positive lead A Fasten the wireharness to the G Fasten the seat lock cable and
7 Seat lock cable assembly frame with a plastic locking tie. wireharness with a band and
8 Battery B Route the brake hose assembly band of the end on inside of the
9 Rodiator reservoir tank through the clamp of engine frame.
10 Ignition coil bracket.
11 Air induction system C Fix the seat lock to the box.
12 Engine ground
20
CABLE ROUTING SPEC
H Fasten the wireharness to the M Clamp the speed sensor lead to Q Clamp the speed sensor lead
frame with a band and the band the front brake hose. Position the and that caliper tightning bolt
of end on inside of the frame. clamp (locatio of the speed sen- and clamp in parallel with front
I Clamp the radiator reservoir sor) to front of the upper clamp fork.
hose. and another clamps to outside. R Fix the starter relay to the foot-
J Fasten the wireharness to the N Through the speed sensor lead rest board.
stay with a band and the end of between front brake caliper and S Clamp the radiator reservoir
band on rearside. bolt. hose and starter motor lead to
K Fasten the speed sensor lead to O Route the speed sensor lead the frame with a plastic clamp.
the stay. through the guide. T Fix the fuse box to the footrest
L Route the front speed sensor P When pull the speed sensor board.
lead and front brake hose lead. Don’t loose. U Fasten the rodiator reservoir
through the clamp on the frame. hose and starter motor lead on
(front side: speed sensor lead the frame with a plastic clamp.
rear side: front brake hose)
21
CABLE ROUTING SPEC
V Fix the turn signal relay on the
footboard.
W Fasten the starter motor lead
and engine ground lead on the
frame with the plastic clamp.
X Route the parking cable and rear
brake hose through the guide.
Y Clamp the A. C. magneto.
22
CABLE ROUTING SPEC
1 Air filter case 14 Auto choke lead D Fasten the wireharness on the
2 Seat lock 15 Brake hose assembly frome with a band and the end of
3 Tensioner 16 A. C. magneto lead band match the tank rail pipe
4 Crankcase breather hose 17 Starter motor lead angle.
5 Fuel sender 18 Engine ground lead E Fix the seat lock cable along the
6 Throttle cable 19 Wireharness guide of panel.
7 Seat lock cable assembly F Fasten the wireharness on the
8 Panel A Don’t turn the idle adjust screw, frame with a plastic clamp.
9 Footrest board when fix the hose. G Fasten the starter motor lead on
10 Radiator resorvoir tank breather B Route the gray seat lock outer the fuel tank brocket with a plas-
hose cable through the left side of tic locking tie.
11 Vacuum hose frame. H Route the starter relay lead to-
12 Throttle position sensor lead C Set the fuel tank sender lead and ward inside.
13 Seat lock sub lead. I Route the battery negative lead
toward inside.
23
CABLE ROUTING SPEC
J Route the thermo unit lead
through the shortest distance
and dont roll another lead but
loose the thermounit lead.
K Route the black seat lock cable
outer through right side of frame.
L Fasten the A. C. magneto lead
starter motor lead and engine
ground lead to the clamp on the
engine bracket.
M Route the crankcase breather
hose into the hole of air filter
case.
24
CABLE ROUTING SPEC
1 Front right turn signal light 16 Panel
2 Relay 17 Auxiliary light lead
3 Front left turn signal light
4 Front brake hose assembly A Don’t loosen the break hose
5 Horn lead (Hi) when fix the break hose.
6 Horn (Hi) B Route the speed sensor lead
7 Throttle cable through the brake hose holder.
8 Speed sensor lead C Fix the front brake hose on the
9 Front brake hose front brake hose holder.
10 Horn (Lo) D Align the white mark H of head-
11 Stay light assembly with the white
12 Seat lock cable tape of coupler lead
13 Leg sealed E Install in stay 1
14 Seat lock cable assembly F To the headlight assembly
15 Inner fender G Clamp near the caupler side root
of auxiliary light lead.
25
INTRODUCTION/ INSP
PERIODIC MAINTENANCE/LUBRICATION INTERVALS ADJ
EB300000
PERIODIC INSPECTIONS AND ADJUSTMENTS

INTRODUCTION
This chapter includes all information necessary to perform recommended inspections and adjust-
ments. These preventive maintenance procedures, if followed, will ensure more reliable vehicle opera-
tion and a longer service life. The need for costly overhaul work will be greatly reduced. This informa-
tion applies to vehicles already in service as well as to new vehicles that are being prepared for sale. All
service technicians should be familiar with this entire chapter.
YP301000
PERIODIC MAINTENANCE/LUBRICATION INTERVALS

Initial EVERY ANNUAL
No
No. ITEM CHECKS AND MAINTENANCE JOB
(1,000 km) 10,000 km 20,000 km CHECK
Check fuel hoses and vacuum hose for cracks or damage.
1 * Fuel line Replace if necessary.

Check condition.
2 Fuel filter Replace if necessary.

Check condition.
3 Spark plug Clean, regap or replace if necessary.

Check valve clearance.

4 * Valves Adjust if necessary.

5 Air filter Clean or replace if necessary.

6 V-belt case air filter Clean or replace if necessary.
Check operation, fluid level and vehicle for fluid leakage.
7 * Front brake Correct accordingly.
Replace brake pads if necessary.
Check operation, fluid level and vehicle for fluid leakage.
8 * Rear brake Correct accordingly.
Replace brake pads if necessary.
Check for cracks or damage.
9 * Brake hoses Replace if necessary.

Check balance, runout and for damage.

10 * Wheels Rebalance or replace if necessary.

Check tread depth and for damage.

Replace if necessary.
11 * Tires Check air pressure.

Correct if necessary.
Check bearing for looseness or damage.
12 * Wheel bearings Replace if necessary.

Check bearing play and steering for roughness.

Correct accordingly.

13
3 * S
Steering
ee g bea
bearings
gs
Lubricate with lithium soap base grease.
Make sure that all nuts, bolts and screws are properly tightened.
14 * Chassis fasteners Tighten if necessary.

Sidestand / centers- Check operation.

15 Lubricate and repair if necessary.

tand
Check operation.
16 * Sidestand switch Replace if necessary.

Check operation and for oil leakage.

17 * Front fork Correct accordingly.

Rear shock absorb- Check operation and shock absorbers for oil leakage.
18 * Replace shock absorber assembly if necessary.

er assemblies
Check engine idling speed and starter operation.
19 * Carburetor Adjust if necessary.

Check oil level and vehicle for oil leakage.

20 Engine oil Correct if necessary. Replace every 3,000 km
Change. (Warm engine before draining.)
Clean or replace every
21 * Engine oil strainer Clean or replace if necessary.
6,000 km
Check coolant level and vehicle for coolant leakage.
Correct if necessary.

22 * Coo g sys
Cooling e
system
Change coolant.
Check oil level and vehicle for oil leakage.
23 Final gear oil Change oil.

24 * V-belt Replace.
26
INSP
PERIODIC MAINTENANCE/LUBRICATION INTERVALS ADJ
Initial EVERY ANNUAL
No
No. ITEM CHECKS AND MAINTENANCE JOB
(1,000 km) 10,000 km 20,000 km CHECK
Front / Rear brake Check operation.

25 * Adjust or replace if necessary.

switch
Moving parts and
26 Lubricate if necessary.
cables
Electrical compo- Check all lights, signals and switches function.

27 * Correct if necessary.
nents Adjust headlight beam if necessary.
*: Since these items require special tools, data and technical skills, they should be serviced by a Yamaha dealer.
EAU02970
NOTE:
The annual checks must be performed once a year unless a 10,000 km or 20,000 km maintenance was
performed in the same year.
The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
Hydraulic brake system
When disassembling the master cylinder or caliper, always replace the brake fluid. Check the brake
fluid level regularly and fill as required.
Replace the oil seals on the inner parts of the master cylinder and caliper every two years.
Replace the brake hoses every four years or if cracked or damaged.
27
INSP
COVER AND PANEL ADJ
COVER AND PANEL
SIDE COVER, SIDE COVER MOLE, PASSENGER SEAT
16 Nm (1.6 mkg)
8 Nm (0.8 mkg)
Order Job name/Part name Q’ty Remarks

Side cover, Side cover panel and Remove the parts in order.
passenger seat removal
1 Passenger seat 1
2 Standing handle 1
3 Side cover mole 3 1
4 Cap 1 1
5 Cap 2 1
6 Side cover 1 1
7 Side cover 2 1
Reverse the removal procedure for
installation.
28
INSP
COVER AND PANEL ADJ
RIDER SEAT AND MAIN BOX
13 Nm (1.3 mkg)
16 Nm (1.6 mkg)
7 Nm (0.7 mkg)

Rider seat and main box removal Remove the parts in order
1 Fuel tank cap 1
2 Cover 1
3 Rider seat 1
4 Side cover 3 1
5 Clip 1 NOTE:
6 Damper assembly 1 Install the damper assembly to the body
with its rod side backward and labels up
ward.
NOTE:
7 Coupler (Seat switch lead) 1 Disconnect the couplers.
8 Pin 1
9 Bottom plate 1
29
INSP
COVER AND PANEL ADJ
RIDER SEAT AND MAIN BOX
13 Nm (1.3 mkg)
16 Nm (1.6 mkg)
7 Nm (0.7 mkg)

10 Bracket 1 NOTE:
11 Coupler (Main box light read) 1 Disconnect the couplers.
12 Seat lock 2
13 Main box 1
installation.
30
INSP
COVER AND PANEL ADJ
SIDE COVER MOLE AND FOOTREST BOARD
7 Nm (0.7 mkg)

Side panel and footrest board removal Remove the parts in order.
1 Mat (footrest board) (left/right) 1/1
2 Cover (footrest board) (left/right) 1/1
3 Cover 2 1
4 Battery negative (–) lead 1
5 Battery positive (+) lead 1
6 Battery 1
7 Flasher relay 1
8 Fuse box 1
9 Starter relay 1
12 Footrest board 1
installation.
31
INSP
COVER AND PANEL ADJ
COWLING, HANDLE COVER, METER ASSEMBLY
7 Nm (0.7 mkg)

Cowling, handle cover, meter Remove the parts in order.
assembly removal
1 Upper cover 1
2 Wind screen 1
3 Inner panel 1
4 Meter assembly 1 NOTE:
5 Coupler (Meter lead) 1 Disconnect the couplers.
6 Cowling body 1
7 Handle cover 1
8 Coupler (headlight lead) 2 NOTE:
9 Coupler (front flasher light lead (left)) 1 Disconnect the couplers.
10 Coupler (front flasher light lead (right)) 1
installation.
32
INSP
COVER AND PANEL ADJ
LEGSHIELD AND FUEL TANK
10 Nm (1.0 mkg)
7 Nm (0.7 mkg)
16 Nm (1.6 mkg)
7 Nm (0.7 mkg)

Legshield and fuel tank removal Remove the parts in order.
1 Legshield 1
2 Inner fender 1
3 Front under braket 1
4 Fuel tank braket 1
5 Fuel hose 1 NOTE:
6 Coupler (fuel sensor lead) 1 Disconnect the couplers.
7 Fuel tank 1
8 Rivet 1
9 Cover 1
Revers the removal procedure for
installation.
33
INSP
ENGINE OIL REPLACEMENT ADJ
ENGINE
ENGINE OIL REPLACEMENT
1. Start the engine and let it warm up for several
minutes.
2. Turn off the engine and place an oil pan un-
der the engine.
3. Remove:
Drain plug 1
Gasket
Drain the crankcase of its oil.
4. Install:
Gasket New
Drain plug 1 20 Nm (2.0 mkg)
5. Fill:
Crankcase
Oil quantity:
1.4 L
6. Check:
Engine oil level
Refer to “ENGINE OIL LEVEL INSPEC-
TION” section.
7. Reset:
Engine oil indicator circuit
Resetting steps:
Turn the main switch to on.
Push and hold in the reset button for 2 to 5 se-
conds.
Release the reset button 1 and the oil indica-
tor light will go off.
NOTE:
If the oil is changed before the oil indicator light
comes on (i.e. before the 3,000 km oil change
interval is reached), be sure to reset the oil indi-
cator light after changing the oil, so that it will
come on at the correct time to indicate the next
3,000 km oil replacement.
To reset the oil indicator light before it comes on:
Release the reset button and the oil indicator
light will come on for 1.4 seconds.
34
INSP
CRANKCASE FILTER CLEANING ADJ
CRANKCASE FILTER CLEANING
1. Remove:
Crankcase filter cover 1
Crankcase filter cover seal
Crankcase filter element
NOTE:
When installing the element in its case, besure
its sealing surface matches the sealing surface
of the case so there is no air leak.
2. Inspect:
Damaged Replace.
CAUTION:
This element is a dry type.
Be careful not to stain with grease or water.
3. Clean:
Crankcase filter element 1
Blow out the dust in the element from the out-
er surface using compressed air.
4. Install:
Crankcase filter cover seal
Crankcase filter cover 7 Nm (0.7 mkg)
35
INSP
AIR INDUCTION SYSTEM INSPECTION ADJ
AIR INDUCTION SYSTEM INSPECTION
1. Remove:
Side cover mole 3
Passenger seat
Standing handle
Side cover 2
Refer to “COVER AND PANEL” section.
2. Inspect:
Hose 3 1
Air filter case 2
Hose 2 3
Air induction system assembly 4
Vacuum hose 5
Pipe 1 6
Hose 1 7
Cracks/damage Replace.
3. Install:
Side cover 2
Standing handle
Passenger seat
Side cover mole 3
36
INSP
COOLANT REPLACEMENT ADJ
YP303180
COOLANT REPLACEMENT
1. Remove:
Side cover mole
Refer to the “COVERS AND PANEL” section.
2. Remove:
Hose 1 (reservoir tank)
Drain the reservoir tank of its coolant.
3. Remove:
Drain bolt 1
Rivet 2
Cover 3
Radiator cap
Open the front trunk, remove the cover, slow-
ly loosen to remove the radiator cap and
drain the coolant.
WARNING
Do not remove the radiator cap when the en-
gine and radiator are hot. Scalding hot fluid
and steam may be blown out under pres-
sure, which could cause serious injury.
When the engine has cooled, open the radia-
tor cap as follows:
Place a thick rag or a towel over the radiator
cap. Slowly rotate the cap counterclockwise
toward the detent. This allows any residual
pressure to escape. When the hissing sound
has stopped, press down on the cap while
turning counterclockwise and remove it.
NOTE:
Remove the radiator cap after removing the
drain bolt.
Place the scooter upright on a level surface
when draining the coolant completely.
4. Clean:
Radiator
Fill soft water into the filler neck support 1
(reservoir tank).
37
INSP
5. Install:
Gasket 1 New
Drain bolt 2 10 Nm (1.0 mkg)
6. Loosen:
Screw 1 (carburetor bleed)
7. Connect:
Hose (reservoir tank)
8. Fill:
Radiator
(to specified level 1 )
Fill the coolant slowly, until the coolant
comes out from the carburetor drain pipe.
Reservoir tank
(to maximum level a )
Recommended coolant:
High quality ethylene glycol
anti-freeze containing
corrosion inhibitors for
aluminium engine.
Coolant 2 and water 3 (soft

water):
Mixed ratio: 50%/50%
Total amount:
1.4 L
Reservoir tank capacity:
0.4 L
Handling notes for coolant:

Coolant is potentially harmful and should be
handled with special care.
38
INSP
WARNING
If coolant splashes in your eyes:
thoroughly wash your eyes with water and
consult a doctor.
If coolant splashes on your clothes:
quickly wash it away with water and then
with soap and water.
If coolant is swallowed:
quickly make the person who has swal-
lowed it vomit and then take him to a doc-
tor.
CAUTION:
Hard water or salt water is harmful to en-
gine parts. Use only distilled water if soft
water is not available.
If you use tap water, make sure it is soft wa-
ter.
Do not use water containing impurities or
oil.
Take care that no coolant splashes onto
painted surfaces. If it does, wash them
straightaway with water.
Do not mix different types of ethylene gly-
col antifreeze containing corrosion inhibi-
tors for aluminum engines.
9. Tighten:
Screw (carburetor bleed)
Fill the coolant slowly to the specified level.
10. Install:
Radiator cap
11. Start the engine and let it warm up for sever-
al minutes.
12. Stop the engine and inspect the level.
Refer to “COOLANT LEVEL INSPECTION”
section.
NOTE:
Wait a few minutes until the coolant settles be-
fore inspecting the coolant level.
13. Install:
Side cover mole
39
INSP
HEADLIGHT BEAM ADJUSTMENT ADJ
ELECTRICAL
HEADLIGHT BEAM ADJUSTMENT
1. Adjust
Headlight beam (vertical)
Turn the adjuster 1 in or out.
Turning in Headlight beam moves

lower.
Turning out Headlight beam moves
higher.
2. Adjust
Headlight beam (horizontal)
Turn the adjuster 1 in or out.
Left headlight

left.
right.
Right head light

right.
left.
40
ENGINE REMOVAL ENG
EB400000
ENGINE OVERHAUL
ENGINE REMOVAL
WIREHARNESS, CABLE, REAR BRAKE
10 Nm (1.0 mkg)
7 Nm (0.7 mkg)

Wireharness, cables and rear brake Remove the parts in order.
removal
Side cover
Main box Refer to “COVER AND PANEL” section.
Footrest board
Drain the coolant. Refer to “COOLANT REPLACEMENT”
section.
Carburetor Refer to “CARBURETOR” section.
1 Spark plug cap 1
2 Thermo unit lead 1
3 Startor coil/Pick up coil lead 1/1
4 Starting motor lead 1
5 Earth lead 1
41
ENGINE REMOVAL ENG
10 Nm (1.0 mkg)
40 Nm (4.0 mkg)

6 Caliper assembly 1
7 Brake hose 1 1
8 Air induction system hose 1
installation.
42
ENGINE REMOVAL ENG
HOSES, AIR FILTER CASE, ENGINE MOUNTING BOLT AND ENGINE
20 Nm ( 2.0 mkg)
32 Nm (3.2 mkg)
64 Nm (6.4 mkg)

Hoses, air filter case, engine mounting Remove the parts in order.
bolt and engine removal
1 Crankcase breather hose 1
2 Inlet hose (water pump) 1
3 Outlet hose (cylinder head) 1
4 Air filter case assembly 1
5 Bolt 2 (Rear shock absorber – lower)
6 Self locknut/Plane washer 1/1 Refer to “ENGINE REMOUNTING”
7 Bolt 1 section.
8 Bolt/Plane washer/Rod assembly 1/2/1
9 Engine 1
installation.
43
CYLINDER HEAD ENG
CYLINDER HEAD
10 Nm (1.0 mkg)
12 Nm (1.2 mkg)
22 Nm (2.2 mkg)
8 Nm (0.8 mkg)
10 Nm (1.0 mkg)
10 Nm (1.0 mkg)

Cylinder head removal Remove the parts in the order.
Drain the coolant.
Side cover Refer to the “COVER AND PANELS”
Main box section.
Footrest board
Carburetor Refer to “CARBURETOR” section.
1 Thermo unit lead 1
2 Plug cap 1
3 Hose 2
4 Outlet hose (cylinder head) 1
5 Vacuum hose 1
6 Breather hose (crankcase) 1
7 Carburetor joint 1
8 Joint 1
9 O-ring 2
44
CYLINDER HEAD ENG
10 Nm (1.0 mkg)
12 Nm (1.2 mkg)
22 Nm (2.2 mkg)
8 Nm (0.8 mkg)
10 Nm (1.0 mkg)
10 Nm (1.0 mkg)

10 Crankcase filter cover 1
11 Pipe 1 1
12 Gasket 1
13 Plug/O-ring 1/1
14 Cam sprocket cover/O-ring 1/1
15 Valve cover (intake side)/O-ring 1/1
16 Valve cover (exhaust side)/O-ring 1/1
17 Timing chain tensioner assembly 1
18 Timing chain tensioner gasket 1 Refer to “CYLINDER HEAD REMOVAL
19 Breather plate 1 AND INSTALLATION” section.
20 Cam sprocket/Timing chain 1/1
21 Cylinder head 1
22 Cylinder head gasket 1
23 Dowel pin 2
installation.
45
V-BELT, CLUTCH AND
SECONDARY/PRIMARY SHEAVE ENG
V-BELT, CLUTCH AND SECONDARY/PRIMARY SHEAVE

CRANKCASE FILTER COVER AND CRANKCASE COVER (LEFT)
10 Nm (1.0 mkg)
10 Nm (1.0 mkg)

Crankcase filter cover and crankcase Remove the parts in order
cover (left) removal
Side cover panel Refer “COVER AND PANEL” section.
1 Crankcase filter cover 1
2 Crankcase cover protector 1
3 Crankcase cover (left) 1
4 Crankcase cover gasket 1
installation.
46
V-BELT, CLUTCH AND
V-BELT, CLUTCH AND SECONDARY/PRIMARY SHEAVE
*Shell BT grease No. 3 (90890-69927)
3 Nm (0.3 mkg)
22 Nm (2.2 mkg)
60 Nm (6.0 mkg)
60 Nm (6.0 mkg)

V-belt, clutch and secondary/ Remove the parts in order.
primary sheave removal
1 Nut/Plain washer 1/1 Refer to “PRIMARY SHEAVE
2 Primary fixed sheave 1 REMOVAL” section.
3 Bracket 1
4 Nut 1
Refer to “SECONDARY SHEAVE AND
5 Spacer/O-ring 1/1
V-BELT REMOVAL” section.
6 Clutch housing 1
Refer to “SECONDARY SHEAVE
7 Clutch assembly 1
INSTALLATION” section.
8 V-belt 1
9 Primary sliding sheave 1
Refer to “PRIMARY SHEAVE
10 Collar 1
ASSEMBLY” section.
11 Primary sheave cap 1
47
V-BELT, CLUTCH AND
*Shell BT grease No. 3 (90890-69927)
3 Nm (0.3 mkg)
22 Nm (2.2 mkg)
60 Nm (6.0 mkg)
60 Nm (6.0 mkg)

12 Cam 1
13 Weight 8
Refer to “PRIMARY SHEAVE
14 Slider 4
ASSEMBLY” section.
15 Spacer 4
16 Oil seal 1
installation.
48
TRANSMISSION ENG
TRANSMISSION
16 Nm (1.6 mkg)

Transmission removal Remove the parts in order.
Rear wheel Refer to “REAR WHEEL/REAR BRAKE”
section.
Crankcase cover (left) Refer to “V-BELT, CLUTCH,
SECONDARY/PRIMARY SHEAVE”
section.
Drain the transmission oil. Refer to “TRANSMISSION OIL
REPLACEMENT” section.
1 Transmission case cover 1
2 Gasket (transmission case cover) 1
3 Dowel pin 2
4 Primary drive gear 1
5 Plain washer 1
6 Plain washer 1
7 1st wheel gear 1
49
TRANSMISSION ENG
16 Nm (1.6 mkg)

8 Conical spring washer 1
9 Drive axle 1
10 Main axle 1
11 Conical spring washer 1
12 Primary driven gear 1
13 Plain washer 1
installation.
50
AIR INDUCTION SYSTEM ENG
AIR INDUCTION SYSTEM

Air induction system removal Remove the parts in the order
1 Clip 1
2 Hose 2 1
3 Clip 1
4 Vacuum hose 1
5 Clip 1
6 Hose 1 1
7 Air induction system assembly 1
installation
51
CRANKCASE AND CRANKSHAFT ENG
CRANKCASE AND CRANKSHAFT

CRANKCASE REMOVAL
1. Remove
Crankcase 2 1
NOTE:
Remove the crankshaft assembly with the
crankcase separating tool 2 .
Make sure that the crankcase separating tool
is centered over the crankshaft assembly.
Crankshaft separating tool

90890-01135
CRANKSHAFT REMOVAL
1. Remove:
Timing chain 1
NOTE:
Before removing the crankshaft assembly, re-
move the timing chain from the crankshaft
sprocket.
If the timing chain hooks to the crankshaft
sprocket, the crankshaft cannot be removed.
crankshaft 1
Remove the crankshaft assembly with the
crankcase separating tool 2
CAUTION:
Do not tap on the crankshaft.
Crankshaft separating tool

90890-01135
CRANKSHAFT INSTALLATION
1. Install:
Crankshaft 1
Crankcase 2
Install the crankshaft assembly with the
crankshaft installer pot 3 , crankshaft install-
er bolt 4 , adapter 5 , spacer 6 .
NOTE:
Hold the connecting rod at top dead center
(TDC) with one hand while turning the nut of the
crankshaft installing tool with the other.
Turn the crankshaft installing tool until the
crankshaft assembly bottoms against the bear-
ing.
Do not tap on the crankshaft.
52
CRANKCASE AND CRANKSHAFT ENG
Crankshaft installer pot 3

90890-01274
Crankshaft installer bolt 4
90890-01275
Adapter 5
90890-01478
Spacer 6
90890-01016
2. Clean all the gascket mating surface and

crankcase surface thoroughly.
3. Apply:
sealant
(onto the left crankcase mating surface)
Yamaha bond No.1215
4. Install:
Timing chain 1
NOTE:
Install the timing chain not to be seen through the
crankshaft hole a on the crankcase (left) 2 .
5. Install:
Crankcase 2 1
Install the crankshaft assembly with the crank-
shaft installer pot 2 , crankshaft installer bolt 3 ,
adapter 4 , spacer 5 .
Crankshaft installer pot 2

90890-01274
Crankshaft installer bolt 3
90890-01275
Adapter 4
90890-01280
Spacer 5
90890-01288
53
RADIATOR COOL
YP500000
COOLING SYSTEM
RADIATOR
23 Nm (2.3 mkg)
23 Nm (2.3 mkg)

Radiator removal Remove the parts in order.
Drain the coolant Refer to “COOLANT REPLACEMENT”
section.
Fuel tank
Footrest board, under cover Refer to “COVER AND PANEL” section.
Cowling body, leg shield
1 Fan motor leads 1
2 Thermo switch leads 2
3 Filler hose (radiator) 1
4 Outlet hose (radiator) 1
5 Inlet hose (radiator) 1
6 Radiator 1
installation.
54
CARBURETOR CARB
EB600000
CARBURETOR
CARBURETOR
10 Nm (1.0 mkg)

Carburetor removal Remove the parts in order.
Side panel
Main box
Drain the coolant Refer to “COOLANT REPLACEMENT”
section.
1 Auto choke lead coupler 1
2 Throttle position sensor lead 1
3 Inlet/Outlet hose (carburetor) 1/1
4 Fuel hose 1
5 Throttle cable 2
CAUTION:
6 Air filter joint 1 Do not bend the air filter joint clamp
when installing the carburetor.
7 Nut 2
8 Carburetor assembly 1
installation.
55
CARBURETOR CARB
CARBURETOR DISASSEMBLY

Carburetor disassembly Disassemble the parts in order.
1 Auto choke unit 1
2 Throttle stop screw set 1
3 Pilot screw set 1
4 Cover/Diaphragm spring 1/1
5 Piston valve 1
6 Jet needle assembly 1
7 Coasting enricher 1
8 Accererating pump 1 Refer to “CARBURETOR ASSEMBLY”
section.
9 Float chamber 1
10 Float pin 1 Refer to “CARBURETOR ASSEMBLY”
section.
56
CARBURETOR CARB

11 Float 1
12 Needle valve 1
Refer to “CARBURETOR ASSEMBLY”
13 Main jet 1
section.
14 Pilot jet 1
15 Main nozzle 1
16 Throttle position sensor 1
Reverse the disassembly procedure
for assembly.
57
CARBURETOR CARB
THROTTLE POSITION SENSOR ADJUST-
MENT
NOTE:
Before adjusting the throttle position sensor
the engine idling speed should be properly ad-
justed.
When installing the throttle position sensor,
adjust its angle according to the RPM which is
displayed on the tachometer, Refer to the ad-
justment procedure below.
1. Turn the main switch to “ON”

2. Loosen:
Throttle position sensor screws 1
3. Inspect:
Throttle position sensor input voltage.
tester (+) lead blue 1

tester (–) lead black 2
Throttle position sensor in put

voltage
5V
Out of specification Check the wireharness

between battery and igniter or igniter and
throttle position sensor.
Throttle position sensor output voltage
tester (+) lead yellow 3

tester (–) lead black 2
Throttle position sensor output

voltage.
0.73 0.63 V
Out of specification Adjust or replace.

NOTE:
When check the throttle position sensor must be
connect the throttle sensor coupler to the wire-
harness.
4. Tighten:
Throttle position sensor screws
58
FRONT WHEEL CHAS
CHASSIS
FRONT WHEEL
SPEED SENSOR AND SENSOR ROTOR
70 Nm (7.0 mkg)
23 Nm (2.3 mkg)

Speed sensor and sensor rotor Remove the parts in order.
removal
Cowling body Refer to “COVER AND PANEL” section.
1 Speed sensor 1
2 Brake caliper 1
3 Axle nut 1
4 Wheel axle 1
5 Front wheel 1
6 Sensor housing 1
7 Collar 1
8 Front wheel sensor lead connector 1 Disconnect the connecter.
installation.
59
FRONT WHEEL CHAS
SPEED SENSOR AND THE SENSOR ROTOR
CAUTION:
Speed sensor cannot be disassembled.
Never disassemble it. If failed, replace with
a new one.
SPEED SENSOR REMOVAL

1. Remove:
Clamp 1
NOTE:
Clamp can be easily removed by moving the
clamp tip of brake hose and speed sensor leads
up and down.
2. Remove:
caliper 1
Speed sensor 2
CAUTION:
Care should be taken not to allow the sen-
sor electrode to contact the metal parts
when removing the speed sensor from the
wheel hub.
To remove the wheel, do not operate the
brake lever.
SPEED SENSOR AND SENSOR ROTOR IN-

SPECTION
1. Check:
Speed sensor 1
Cracks, bending and distortion Replace
Iron powder and dust Clean
60
FRONT WHEEL CHAS
2. Measure:
: Speed sensor resistance
Connect the pocket tester (Ω 1) to the ter-
minal of speed sensor connector.
Tester’s positive (+) lead Terminal 1
Tester’s negative (–) lead Terminal 2
Regulated resistance:
1.19 to 2.21 kΩ at 20_C
Out of specification Replace
3. Check:
: Sensor rotor 1
Cracks and damage Replace the wheel
assembly
NOTE:
Sensor rotor of YP250 is inserted under pres-
sure by the special process and cannot be re-
placed as a single unit. To replace the sensor ro-
tor, replace it as a wheel assembly.
SPEED SENSOR ASSEMBLY

Proceed in the reverse order of disassembling
paying attention to the following items.
1. Apply:
: Litium soap base grease
1 Wheel axle
61
FRONT WHEEL CHAS
2. Install:
Sensor housing
3. Install:
Front wheel
Wheel axle
Axle nut 70 Nm (7.0 mkg)
NOTE:
Align the slot of sensor housing with the projec-
tion part of front fork, then assemble them.
CAUTION:
Install after checking if foreign materials are
mixed in the wheel hub. If foreign materials
are mixed, it causes to damage the sensor
rotor and speed sensor.
4. Install:
Speed sensor 1 23 Nm (2.3 mkg)
Brake caliper 2 50 Nm (5.0 mkg)
Clamp 3
NOTE:
When installing the speed sensor, check if the
speed sensor lead is twisted or foreign matters
attached to the electrode.
CAUTION:
To route the speed sensor lead, refer to the
CABLE ROUTING.
62
FRONT WHEEL CHAS
5. Install:
Speed sensor lead 1
63
REAR WHEEL CHAS
REAR WHEEL

Rear wheel and brake disc removal
Swingarm Refer to “REAR SHOCK ABSORBER
AND SWINGARM” section.
1 Plate 1
2 O-ring 1
3 Collar 1
4 Rear wheel 1
installation.
64
REAR SHOCK ABSORBER AND SWINGARM CHAS
REAR SHOCK ABSORBER AND SWINGARM
40 Nm (4.0 mkg)
20 Nm (2.0 mkg)
40 Nm (4.0 mkg)
135 Nm (13.5 mkg)
35 Nm (3.5 mkg)
53 Nm (5.3 mkg)

Rear shock absorber and swingarm Remove the parts in order.
removal
Side panels Refer to “COVER AND PANEL” section.
NOTE:
1 Nut 2 Loosen.
2 Muffler assembly 1
NOTE:
3 Axle nut 1 Remove with the rear brake applied.
4 Rear shock absorber 2
5 Rear caliper assembly 1
6 Swingarm 1
7 Collar 1
8 Oil seal 1
9 Bearing 1
10 Oil seal 1
installation.
65
ELECTRICAL COMPONENTS ELEC
EB800000
ELECTRICAL
ELECTRICAL COMPONENTS
1 Main switch 9 Fuel pump
2 Ignition coil 10 Sidestand switch
3 Spark plug cap 11 Flasher relay
4 Fuel sender 12 Battery
5 Rectifier/ Regulator 13 Starter relay
6 Wireharness 14 Starting circuit cut-off relay
7 Thermo unit 15 Horn
8 Ignitor unit 16 Fuel pump relay
66
CIRCUIT DIAGRAM ELEC
CIRCUIT DIAGRAM
67
CIRCUIT DIAGRAM ELEC
1 A.C. magneto 32 Thermo switch (Fan)
2 Pickup coil 33 Fan motor
3 Rectifier regulator 34 Brake light switch
4 Main switch 35 Flasher relay
5 Backup fuse 36 Horn
6 Battery 37 Turn switch
7 Main fuse 38 Horn switch
8 Starter relay 39 Dimmer switch
9 Starter motor 40 Pass switch
10 Diode 41 Left handlebar switch
11 Starting circuit cut-off relay 42 License plate light
12 Thermo switch (Auto choke) 43 Tail/ brake light
13 Auto choke 44 Rear flasher light
14 Ignitor unit 45 Front flasher light
15 Ignition coil 46 Head light (LO)
16 Spark pulg 47 Head light (HI)
17 Throttle position sensor 48 Auxiliary light
18 Speed sensor 49 Trun signal indicator light
19 Fuel pump 50 High beam indicator light
20 Fuel pump relay 51 Meter light
21 Sidestand switch 52 Oil indicator light
22 Light switch 53 Fuel gauge
23 Start switch 54 Thermometer
24 Engine stop switch 55 Clock
25 Right handlebar switch 56 Speedometer
26 Ignition fuse 57 Meter assembly
27 Seat switch 58 Fuel sender
28 Box light 59 Thermo unit
29 Head light fuse 60 Alarm
30 Fan fuse 61 Grip warmer switch (OPUTION)
31 Signal fuse 62 Grip warmer (OPUTION)
63 Ground
NOTE:
Starter switch is closed while the button (switch) is pushed.
Sidestand switch is closed while the side stand is upped.
Brake switch is closed while the brake is applied.
COLOR CODE
B Black W White L/Y Blue/Yellow

Br Brown B/R Black/Red L/W Blue/White
Ch Chocolate B/W Black/White R/G Red/Green
Dg Dark green Br/L Brown/Blue R/Y Red/Yellow
G Green Br/W Brown/White R/W Red/White
L Blue G/R Green/Red Y/R Yellow/Red
O Orange G/Y Green/Yellow Y/L Yellow/Blue
P Pink L/B Blue/Black W/G White/Green
R Red L/G Blue/Green
Y Yellow L/R Blue/Red
68
CHECKING SWITCHES ELEC
YP*****
CHECKING SWITCHES
SWITCH POSITION AND TERMINAL CONNECTION
Before checking a switch refer to the checking

switches as shown in the left page and check for
the correct terminal connections (closed circuit)
according to the color combinations shown in
the chart.
Poor connection, fault Repair or replace.
69
CHECKING SWITCHES ELEC
YP-N
CHECKING SWITCHES
CHECKING STEPS
Using pocket tester, check switches for continu-
ity between their terminals to determine wheth-
er they are correctly connected.
Replace the switch component if any of the
combinations does not produce the correct
reading.
Pocket tester:
90890-03112
NOTE:
Turn the switch to the “ON”, “OFF” positions
several times.
Adjust the pocket tester to correct “0” position
before checking switches.
Set the pocket tester selector to “ 1” Ω.
SWITCH CONNECTION AS SHOWN IN THIS

MANUAL
This manual contains connection charts, like
the one shown on the left, showing the terminal
connections of switches (e.g. the main switch,
handlebar switch, brake switch, lighting switch
etc.)
The column on the extreme left indicates the dif-

ferent switch positions, the top line indicates the
colors of the leads connected to the terminals
on the switch.
“ ” indicates terminals between which

there is continuity, i.e. a closed circuit, in the giv-
en switch position.
In this chart:
“Br and R” have continuity with the switch in the
“ON” position.
70
IGNITION SYSTEM ELEC
EB802000
IGNITION SYSTEM
CIRCUIT DIAGRAM
2 Pickup coil
4 Main switch
6 Battery
7 Main fuse
14 Ignitor unit
15 Ignition coil
16 Spark plug
21 Sidestand switch
24 Engine stop switch
60 Alarm
71
ELECTRIC STARTING ELEC
EB80300
ELECTRIC STARTING SYSTEM

CIRCUIT DIAGRAM
4 Main switch
6 Battery
7 Main fuse
8 Starter relay
9 Starter motor
11 Starting circuit cut-off relay
21 Sidestand switch
23 Starter switch
26 Ignition fuse
31 Signal fuse
34 Brake light switch
60 Alarm
72
LIGHTING SYSTEM ELEC
EB804000
LIGHTING SYSTEM
CIRCUIT DIAGRAM
4 Main switch 40 Pass switch

5 Backup Fuse 42 License plate light
6 Battery 45 Tail/Brake light
7 Main fuse 46 Head light (Lo)
22 Lights switch 47 Head light (HI)
27 Seat switch 48 Auxiliary light
28 Box light 50 High beam indicator light
29 Head light fuse 51 Meter lights
39 Dimmer switch
73
YP805010
TROUBLESHOOTING
IF THE HEADLIGHT, HIGH BEAM

INDICATOR LIGHT, TAILLIGHT,
BOX LIGHT, LICENSE PLATE LIGHT AND/
OR METER LIGHT FAIL TO COME ON.
Procedure
Check: 5. Dimmer switch and pass switch
1. Fuse (Main, Backup) 6. Seat switch
2. Battery 7. Wiring connection (entire lighting system)
3. Main switch
4. Lights switch
NOTE:
Remove the following parts before trouble-
shooting.
1) Rider seat
2) Passenger seat
3) Box
4) Legshield
5) Cowling body
Use the special tools specified in the trouble-
shooting section.
Pocket tester
90890-03112
YP****** NO CONTINUITY
1. Fuse
Refer to “CHECKING SWITCHES” section.
Replace the fuse.
CONTINUITY
YP******
INCORRECT
2. Battery
Check the battery condition.
Refer to “BATTERY INSPECTION” section Clean battery terminals.
in CHAPTER 3. Recharge or replace battery.
CORRECT
3. Main switch
Replace the main switch.
CONTINUITY
YP******
NO CONTINUITY
4. Lights switch
Replace the right handlebar switch.
CONTINUITY

74

5. Dimmer switch/Pass switch
Replace the left handlebar switch.
6. Seat switch
Replace the handlebar switch.
YP******
7. Wiring connection POOR CONNECTIONS

Check the connections of the entire lighting
system.
Refer to “WIRING DIAGRAM”. Correct.
Check the condition of each of the lighting

system’s circuits.
Refer to “LIGHTING SYSTEM CHECK”
YP805020
LIGHTING SYSTEM CHECK

1. If the headlight and the high beam indicator light fail to come on.
1. Bulb and bulb socket NO CONTINUITY
CONTINUITY
Replace the bulb and/or bulb socket.
2. Voltage
Connect the pocket tester (DC20 V) to the
headlight and high beam indicator light cou-
plers.
A When the dimmer switch is on low beam.
B When dimmer switch is on high beam or
the Pass switch is pushed.
Headlight:
Tester (+) lead Green 1 or Yellow 2
lead
Tester negative (–) lead Black 3
lead
High beam indicator light:
Tester (+) lead Yellow 4 lead
Tester (–) lead Black 5 lead

75


Turn the light switch to on position. OUT OF SPECIFICATION
Turn the dimmer switch to low beam or high
beam.
Pass switch to push in. The wiring circuit from the main switch to
Check for voltage (12 V) on the lead at bulb bulb socket connector is faulty. Repair.
socket connectors.
MEETS
SPECIFICATION
This circuit is not faulty.
YP805021
2. If the meter light fails to come on.

NO CONTINUITY
1. Bulb and bulb socket
CONTINUITY
2. Voltage
bulb socket coupler.
Tester (+) lead
Blue terminal 1
Tester (–) lead
Black terminal 2

Turn the lights switch to on or pilot position.
Check the voltage (12 V) of the leads on the OUT OF SPECIFICATION
bulb socket connector.
MEETS The wiring circuit from main switch to bulb

SPECIFICATION socket is faulty. Repair.
76
YP805022
3. The taillight fails to come on.

NO CONTINUITY
CONTINUITY
2. Voltage
Tester (+) lead
Blue terminal 1
Tester (–) lead
Black terminal 2
OUT OF SPECIFICATION

The wiring circuit from main switch to bulb
connector is faulty. Repair.
Check the voltage (12 V) on the bulb socket
connector.
MEETS
SPECIFICATION
77
YP805022
3. The license plate light fails to come on.

NO CONTINUITY
CONTINUITY
2. Voltage
Tester (+) lead
Blue terminal 1
Tester (–) lead
Black terminal 2

connector.
MEETS
SPECIFICATION
78
YP805023
4. If the auxiliary light fails to come on.

NO CONTINUITY
CONTINUITY
2. Voltage
Tester (+) lead Blue/Red terminal 1
Tester (–) lead Black terminal 2

connector.
MEETS
SPECIFICATION
79
SIGNAL SYSTEM ELEC
EB806000
SIGNAL SYSTEM
CIRCUIT DIAGRAM
4 Main switch 38 Horn switch

6 Battery 43 Tail/ Brake light
7 Main fuse 44 Rear flasher lights
31 Signal fuse 45 Front flasher lights
34 Brak light switch 49 Turn indicator lights
35 Flasher relay 53 Fuel gauge
36 Horn 58 Fuel sender
37 Turn switch
80
SIGNAL SYSTEM ELEC
YP806010
TROUBLESHOOTING
IF THE FLASHER LIGHT, BRAKE

LIGHT AND/OR INDICATOR LIGHT
FAIL TO COME ON.
IF THE HORN FAILS TO SOUND.
Procedure
Check:
3. Main switch
1. Fuse (Main, signal) 4. Wiring connection (entire signal system)
2. Battery
NOTE:
shooting.
1) Cowling body
2) Side panels
Use the special tools in the troubleshooting
section.
Pocket tester:
90890-03112
1. Fuse
Replace the fuse.
CONTINUITY
YP******
INCORRECT
2. Battery
CORRECT
3. Main switch
CONTINUITY

81
SIGNAL SYSTEM ELEC

YP******
4. Wireharness
POOR CONNECTION
Check the connections of the entire signal
system.
Refer to “CIRCUIT SYSTEM WIRING DIA-
GRAM” section. Correct.
CONTINUITY
Check condition of each of the signal sys-

tem’s circuits.
Refer to “SIGNAL SYSTEM CHECK” section.
82
SIGNAL SYSTEM ELEC
YP806020
SIGNAL SYSTEM CHECK

1. If the horn fails to sound. NO CONTINUITY
1. HORN switch
CONTINUITY
2. Voltage
horn lead.
Tester (+) lead Brown terminal 1
Tester (–) lead Frame ground
Check for voltage (12 V) on the “Brown” lead OUT OF SPECIFICATION
at the horn terminal.
The wiring circuit from the main switch to the

horn is faulty. Repair.
MEETS
SPECIFICATION
3. Horn
horn at the “Pink” terminal.
Tester (+) lead Pink 1 terminal
Check for voltage on the “Pink” lead to frame NO CONTINUITY
ground.
CONTINUITY Replace the horn.
Adjust or replace horn.
83
SIGNAL SYSTEM ELEC
YP806022
2. If the brake light fails to come on:

NO CONTINUITY
CONTINUITY
NO CONTINUITY
2. Brake switch (Front/Rear)
Replace brake switch.
CONTINUITY
3. Voltage
Tester (+) lead Yellow terminal 1
Turn the main switch to on. OUT OF SPECIFICATION

The brake lever is pulled in.
Check for voltage (12 V) of the “Yellow” lead
on the bulb socket connector. 4. Wiring connection
MEETS Wiring circuit from the main switch to the
SPECIFICATION bulb socket connector is faulty. Repair.
This circuit is not faulty. Refer to “SIGNAL SYSTEM WIRING DIA-
GRAM”.
84
SIGNAL SYSTEM ELEC
YP806023
3. If the flasher light and/or turn indicator light fails to blink.

NO CONTINUITY
CONTINUITY
NO CONTINUITY
2. Turn switch
CONTINUITY
3. Voltage
flasher relay coupler.
Tester (+) lead Brown terminal 1
Check for voltage (12 V) of the “Brown” OUT OF SPECIFICATION
1 lead at the flasher relay terminal.
MEETS
The wiring circuit from main switch to flasher
SPECIFICATION
relay connector is faulty. Repair.
4. Voltage
flasher relay coupler.
Tester (+) lead
Brown/White terminal 1
Check for voltage (12 V) on the “Brown/ OUT OF SPECIFICATION
White” lead at the flasher relay terminal.
MEETS
The flasher relay is faulty. Replace.
SPECIFICATION

85
SIGNAL SYSTEM ELEC

5. Voltage
At flasher light (left)
Tester (+) lead Chocolate lead 1
At flasher light (right)
Tester (+) lead Dark green lead 2
Turn the turn switch to left or right.
Check for voltage (12 V) on the “Chocolate” OUT OF SPECIFICATION
lead and “Dark green” at the flasher light ter-
minal.
6. Wiring connection
MEETS
SPECIFICATION Wiring circuit from the turn switch to bulb
socket connector is fault. Repair.
This circuit is not faulty. Refer to “CIRCUIT DIAGRAM”.
86
SIGNAL SYSTEM ELEC
YP806027
4. If the fuel gauge fails to operate.
1. Fuel sender
Remove the fuel sender from the fuel tank.
Disconnect the fuel sender coupler from the
wireharness.
Connect the pocket tester (Ω 10) to the
fuel sender coupler lead.
Tester (+) lead Green terminal 1
Check the fuel sender for specificated resis-
tance.
Specificated
Float position OUT OF SPECIFICATION
resistance
UP 3 4 10 Ω
DOWN 4 90 100 Ω
BOTH MEET Replace the fuel sender.
SPECIFICATION
2. Voltage
fuel gauge coupler.
Tester (+) lead
Brown terminal 1
Tester (–) lead
Frame ground
Turn the main switch to “ON”. OUT OF SPECIFICATION

Check for voltage (12 V) of the “Brown” lead
on the fuel sender lead.
Check the connection of the entire signal
MEETS system.
SPECIFICATION Refer to “CHECKING OF CONNECTIONS”.
Refer to “CIRCUIT DIAGRAM”.
87
SIGNAL SYSTEM ELEC
3. Fuel gauge
Connect the fuel sender to wireharness. NOTE:
Move the float to “UP” 1 or “DOWN” 2. Before reading the meter, stay put the float for
more than three minutes respectively at “UP”
or “DOWN”.
Turn the main switch to “ON”.

Check the fuel gauge needle moves “F” or DOES NOT MOVE
“E”.
Float position Needle moves
Float “UP” 1 “F” Replace the fuel gauge.
Float “DOWN” 2 “E”
MOVES
88
FUEL PUMP SYSTEM ELEC
EB808000
FUEL PUMP SYSTEM

CIRCUIT DIAGRAM
4 Main switch
6 Battery
7 Main fuse
14 Ignitor unit
19 Fuel pump
20 Fuel pump relay
26 Ignition fuse
89
EB808010
FUEL PUMP CIRCUIT OPERATION

The ignitor unit includes the control unit for the fuel pump.
1 Battery
2 Main fuse
3 Main switch
4 Ignition fuse
6 Ignitor unit
7 Fuel pump relay
8 Fuel pump
90
EB808020
TROUBLESHOOTING
The fuel pump fails to operate.
Procedure
Check: 5. Relay unit (fuel pump relay)
1. Fuse (Main and Ignition) 6. Fuel pump
2. Battery 7. Wiring connection
3. Main switch (engine fuel pump system)
4. Engine stop switch
NOTE:
shooting.
1) Rider seat
2) Passenger seat
3) Box
4) Legshield
Use the special tools specified in the trouble-
shooting section.
Pocket tester
90890-03112
1. Fuse
Replace the fuse.
CONTINUITY
YP******
INCORRECT
2. Battery
CORRECT
3. Main switch
CONTINUITY
YP******
NO CONTINUITY
4. Engine stop switch
Replace the right handlebar switch.
CONTINUITY

91
:
5. Relay unit (fuel pump relay)
Disconnect the relay unit from the coupler.

Connect the pocket tester (Ω 1) and bat-
tery (12 V) to the relay unit terminals as
shown.
Battery positive terminal red/white 1

Battery negative terminal blue/red 2
Tester positive probe red/white 3

Tester negative probe blue/black 4 NO CONTINUITY

Check the starter relay for continuity.
Replace the starter relay
CONTINUITY
6. Fuel pump resistance
Disconnect the fuel pump coupler from the

wire harness.
Connect the pocket tester (Ω 1) to the fuel
pump coupler (fuel pump side) as shown.
Tester positive probe black/blue 1
Tester negative probe black 2
Measure the fuel pump resistance. OUT OF SPECIFICATION

Fuel pump resistance
11 13 Ω at 20_C
CORRECT Replace the fuel pump
7. Wiring connection
POOR CONNECTION
Check the entire fuel pump system’s wiring.
Refer to “CIRCUIT DIAGRAM”.
CORRECT
Correct.
Replace the ignition unit
92
EB808410
CHECKING THE FUEL PUMP

WARNING
Gasoline is extremely flammable and under
certain circumstances there can be a danger
of an explosion or fire. Be extremely careful
and note the following points:
Stop the engine before refuelling.
Do not smoke and keep away from open
flames, sparks or any other source of fire.
If you do accidentally spill gasoline, wipe it
up immediately with dry rags.
If gasoline touches the engine when it is
hot, a fire may occur. Therefore, make sure
that the engine is completely cool before
performing the following test.
1. Check:
Fuel pump operation
a. Fill the fuel tank.

b. Put the end of the fuel hose into an open con-
tainer.
c. Turn the fuel cock to “ON” or “RES”.
d. Connect the battery (12 V) to the fuel pump
coupler as shown.
Battery positive lead black/blue 1

Battery negative lead black 2
e. If fuel flows out of the fuel hose, the fuel pump

is OK. If fuel does not flow, replace the fuel
pump.
93
YP250 2000 WIRING DIAGRAM
1 A. C. magneto 41 Left handlebar switch
2 Pickup coil 42 License plate light
3 Rectifier regulator 43 Tail / brake light
4 Main switch 44 Rear flasher light
5 Backup fuse 45 Front flasher light
6 Battery 46 Head light (LO)
7 Main fuse 47 Head light (HI)
8 Starter relay 48 Auxiliary light
9 Starter motor 49 Trun signal indicator light
10 Diode 50 High beam indicator light
11 Starting circuit cut-off relay 51 Meter light
12 Thermo switch (Auto choke) 52 Oil indicator light
13 Auto choke 53 Fuel gauge
14 Ignitor unit 54 Thermometer
15 Ignition coil 55 Clock
16 Spark pulg 56 Speedometer
17 Throttle position sensor 57 Meter assembly
18 Speed sensor 58 Fuel sender
19 Fuel pump 59 Thermo unit
20 Fuel pump relay 60 Alarm
21 Sidestand switch 61 Grip warmer switch (OPTION)
22 Light switch 62 Grip warmer (OPTION)
23 Start switch 63 Ground
25 Right handlebar switch
26 Ignition fuse
27 Seat switch
28 Box light
29 Head light fuse
30 Fan fuse
31 Signal fuse
32 Thermo switch (Fan)
33 Fan motor
34 Brake light switch
35 Flasher relay
36 Horn
37 Turn switch
38 Horn switch
39 Dimmer switch
40 Pass switch
COLOR CODE
B ........ Black Br / W . . . . . Brown / White
Br . . . . . . . Brown G/R . . . . . Green / Red
Ch . . . . . . Chocolate G / Y. . . . . . Green / Yellow
Dg . . . . . . Dark green L/B . . . . . . Blue / Black
G ....... Green L/G . . . . . . Blue / Green
L ........ Blue L/R . . . . . . Blue / Red
O ....... Orange L/Y . . . . . . Blue / Yellow
P ........ Pink L/W . . . . . Blue / White
R........ Red R/G . . . . . Red / Green
Y ........ Yellow R/Y. . . . . . Red / Yellow
W ....... White R/W . . . . . Red / White
B/R. . . . . . Black / Red Y/R. . . . . . Yellow / Red
B/W . . . . . Black / White Y/L . . . . . . Yellow / Blue
Br / L . . . . . Brown / Blue W/G . . . . . White / Green

YP250 Service Manual

Uploaded by

Copyright:

Available Formats

YP250 Service Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

YP250 Service Manual

Uploaded by

Copyright:

Available Formats

What is the purpose of this manual?

What is the purpose of this manual?

What are some important symbols used in the manual?

What are some important symbols used in the manual?

FOREWORD

YP250 SERVICE MANUAL: 4UC-AE1

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR

NOTE: A NOTE provides key information to make procedures easier or clearer.

HOW TO USE THIS MANUAL

ADJ ENG 3 Periodic inspection and adjustment

24 25 24 Apply locking agent (LOCTITE)

PERIODIC INSPECTIONS AND ADJUSTMENTS

VEHICLE IDENTIFICATION NUMBER (for E)

FRAME SERIAL NUMBER (except for E)

ENGINE SERIAL NUMBER

Tool No. Tool name/Usage Illustration

This tool is used to remove the crankshaft.

Periodic oil change 1.2 L

Item Standard Limit

Item Standard Limit

Item Standard Limit

Item Standard limit

Item Standard limit

LUBRICATION POINTS AND GRADE OF LUBRICANT

Lubrication Point Symbol

Lubrication Point Symbol

PERIODIC INSPECTIONS AND ADJUSTMENTS

PERIODIC MAINTENANCE/LUBRICATION INTERVALS

Check valve clearance.

5 Air filter Clean or replace if necessary.

Check balance, runout and for damage.

Check tread depth and for damage.

Check bearing play and steering for roughness.

Sidestand / centers- Check operation.

Check operation and for oil leakage.

Check oil level and vehicle for oil leakage.

Front / Rear brake Check operation.

Electrical compo- Check all lights, signals and switches function.

Order Job name/Part name Q’ty Remarks

RIDER SEAT AND MAIN BOX

Order Job name/Part name Q’ty Remarks

RIDER SEAT AND MAIN BOX

Order Job name/Part name Q’ty Remarks

SIDE COVER MOLE AND FOOTREST BOARD

Order Job name/Part name Q’ty Remarks

COWLING, HANDLE COVER, METER ASSEMBLY

Order Job name/Part name Q’ty Remarks

LEGSHIELD AND FUEL TANK

Order Job name/Part name Q’ty Remarks

Coolant 2 and water 3 (soft

Handling notes for coolant:

Turning in Headlight beam moves

Turning in Headlight beam moves

Turning in Headlight beam moves

Order Job name/Part name Q’ty Remarks

Order Job name/Part name Q’ty Remarks

HOSES, AIR FILTER CASE, ENGINE MOUNTING BOLT AND ENGINE

Order Job name/Part name Q’ty Remarks

Order Job name/Part name Q’ty Remarks

Order Job name/Part name Q’ty Remarks