Bomba de Engranajes Kracht KP5 - GB - 09-08

High Pressure Gear Pumps
KP 5
High Pressure Gear Pumps KP 5
Construction
1
1 Housing
2 Gearing
3 Drive shaft end
4 Flange cover
5 Roller bearing
6 Sliding plates
7 Lip-type shaft seal
8 Plain bearing
9 Housing gasket
Description
Technical Information
KP series high pressure gear pumps are mainly used

in oil-hydraulic plants. They are suitable both for
hydraulic fluids as well as mineral oil bases
(DIN 51524/25) and engine oils (DIN 51511).
1. External loads
The robust design facilitates handling external
radial forces, depending on the size and direction
of application.
The housing components are made from high-grade

cast iron, the shaft and gears from hardened and
ground case-hardening steel.
2. Direction of rotation
The following stipulations apply to the direction of
rotation when looking at the drive shaft end:
The shafts are supported in multi-layer bearings that

have excellent antifriction properties. The seals
in the drive shaft ends are made using solely NBR
or FKM shaft seals.
An outboard bearing is placed on the shaft end to
handle radial and axial forces.
Shaft rotation clockwise: direction of conveyance

from left to right
Shaft rotation
counter clockwise:
direction of conveyance
from right to left
The use of fine-meshed filters significantly increases

the gear pump service life. Careful maintenance is
the prerequisite.
KRACHT GmbH Gewerbestr. 20 58791 Werdohl, Germany fon +49 (0) 23 92 / 935-0 fax +49 (0) 23 92 / 935 209 mail [email protected] web www.kracht.eu
General Characteristics
Calculation Formulas for Hydropumps
Fixing type
Flange type
Characteristics, formula signs, units
Pipe connection
Flange;
Dimensions, page 8
1 Discharge / displacement flow
l/min
2 geom. discharge / displ. flow
Vg
cm3/r
Drive shafts
Dimensions, page 8
3 Pressure
bar
Direction of rotation
clockwise or anticlockwise
4 Speed
1/min
Weight
Page 7
5 Torque
Nm
Mounting position
optional
6 Power
kW
Ambient temperature u min

u max
= -- 20 C
= + 60 C
Operating Characteristics
Operating pressure
7 Total efficiency
tot
8 Volumetric efficiency
vol
9 hydr./ mech. efficiency
hm
10 Flow velocity
m/s
11 Piping diameter
mm
Inlet port
pe min = -- 0.4 bar (underpressure)

pe max = 2.0 bar
General:
Outlet port
p max = Table, page 5
Qth = Vg n,
m min = -- 20 C
m max= + 80 C for NBRLip-type shaft seal
M = 9549 P
n
+ 120 C for FKM-
Lip-type shaft seal

min = 13 mm2/s (cSt)
max = 600 mm2/s (cSt)
Recommended
viscosity range
Discharge flow
Page 5
Input power
Page 5
Filter fineness
Return line filter

0.060 mm mesh size
Hydraulic fluids
Mineral oil based on

DIN 51524/25
Motor oil based on
DIN 51511
flameproof hydraulic fluids
on request
KP 5
0.85
0.95
= 16 90 mm2/s (cSt)
Accessories
Straight flange connection, hole pattern based on
SAE standard. Differential coupling for cyl. shaft end.
Intermediate flange to standard motors with
fastening flange according to DIN 42948.
Volume
flow
Products and media on request
Pump
Discharge flow
Q=
Vg n vol
103
l
min
Torque
ATEX
n
M
P
Drive torque
M=
p Vg
20 hm
[Nm]
Performance
Viscosity
tot = vol hm
p = M n v = 21,22 Q
9549
d2
Recommended values for KRACHT products

at the nominal operating pressure
tot
vol
Parameters for:
Fluid temperature
Input power
P=
pQ
600 tot
[kW]
Displacement / Nominal Size

Displacement
Nominal size
geom.
displacement
max.
operatng
pressure
Speed range
Torque
Permitted torques
in N middle
at shaft ends
Mass inertia
torque x 10-3
Vg
cm3/r
pb
bar
nmin
1/min
nmax
Mmax
Nm
(n = 1450 1/min)
axial
radial
J
kg/m2
160
160
100
800
2000
200
200
100
800
1800
250
250
100
800
1600
300
300
80
800
1500
3.77
560
400
1500
4.57
5.87
6.50
Discharge Flow and Required Input Power

Discharge flow at n = 950 1/min
Discharge flow Q in 1/min at 34 mm2/s
Pressure p in bar
Nominal size
10
20
40
60
80
100
160
150
149
147
146
144
143
200
190
189
187
185
183
181
250
239
238
236
234
232
230
300
286
285
284
283
281
Required input power P in kW at n = 950 1/min

Nominal size
Pressure p in bar
10
20
40
60
80
100
160
3.5
6.5
12
17.5
23
29
200
14.5
22
29
36
250
9.5
18
26.5
35
43.5
300
11.5
21.5
32
42.5
Discharge flow at n = 1450 1/min

Discharge flow Q in 1/min at 34 mm2/s
Pressure p in bar
Nominal size
10
20
40
60
80
100
160
227
225
223
221
219
216
200
285
284
282
280
278
276
250
358
356
354
352
349
346
300
429
428
426
424
422
Required input power P in kW at n = 1450 1/min

Nominal size
Pressure p in bar
10
20
40
60
80
100
160
5.5
10
18.5
27
36
44.5
200
6.5
12
23
33.5
43.5
54
250
8.0
14
27.5
41
54
67
300
9.5
17.5
33
49
64.5
Tolerance zone of the discharge flow: -- 5 % of table value Q.

Select the delivery power of each drive motor approx. 20 % greater than table value P.
If the viscosity is less than 30 mm2/s (cSt), reduce discharge flow Q
If the viscosity is more than 75 mm2/s (cSt), consider the addition to the input power,
if over 300 mm2/s (cSt), reduction of the speed.
Type Key
Ordering example
KP 5 /160 C 1 0 K T 0 0 0 D E 1 /.
Code for
special design
Seals
1 NBR lip-type shaft seal

2 FKM lip-type shaft seal
Type of gearing
E transmission made of
case-hadening steel,
hardened and bround
Code for materials

Housing and bearing execution
D Cast iron housing with
multi component plain bearing
Construction code
0 (internal allocation)
Adaptor piece
0 without
2. Shaft end
0 without
Shaft ends
T Spline profile SAE-C, z = 14; DP 12/24 = 30
V Spline profile W 40 x 2 DIN 5480
Z Cylindrical shaft 38
Housing ports
K Inlet port 2 12" SAE connection ( 65)
Outlet port 2" SAE connection ( 50)
Mounting equipment / Outboard bearing

0 without
Direction of rotation
1 clockwise
2 anti clockwise
Flange cover version
C SAE-C-2 hole flange, LA = 181; z = 127
E SAE-C-4 hole flange, LA = 114,55;; z = 127
E LA = hole clearance, z = pitch circle diameter
Displacement
160 / 200 / 250 / 300
Size 5
Dimensions
Displacement
Weight in kg
Nominal size
Version
C flange
Version
E flange
160
225
170
42
43
200
230
175
44
45
250
243
188
48
49
300
255
200
52
53
Flange Type
SAE-C-2 hole flange
LA = 181; z = 127
C,
SAE-C-4 hole flange E,

LA = 114.55; z = 127
Connections
Housing side ports
Inlet port 2 12" SAE connection ( 65)
Housing side ports

Outlet port 2" SAE connection ( 50)
Shaft Ends
Shaft end T
Spline profile SAE-C
Z = 14; DP 12/24, = 30
Shaft end V
Spline profile W 40 x 2, DIN 5480
Shaft end Z
Cylindrical shaft 38
Accessory, Couplings
Version A
Part 1
Version B
Part 1
Part 1
Part 2
Gear rim off

Polyurethane (Vulkollan)
with 92 shore hardness
Colour: natural
RA 38
RG
Ordering code
Hub material
A
G
Coupling
size
Hub material
Weight
Version A
Kg
Version B
Coupling size
in Al (aluminium)
in GG (cast iron)
AL
GG
Al
Lead
bore
GG
Z 45/38
Z 45/38
Coupling hub length

and hub bore
Pump side cylindrical
Finished bore
Coupling hub length

and hub bore
Motor side zylindrical
Dimensions
min.
max.
Mass Weight Mass
Part
Part
Part
Part
Part
Part
moment
moment
2
1
2
1
2
of inertia
of inertia 1
2
2
Kgm
Kg
Kgm
l1 ;
l2 E
L M
Ordering code
DH
D1 dH
Al GG
38
0.82
0.0007
2.08
0.002
10
12
38
45 24
18 114 37
80 66 66
38
R.38 -Z 45/..-Z 45/..
42
1.25
0.0014
3.21
0.004
12
14
42
50 26
20 126 40
95 75 75
46
R.42 -Z 50/..-Z 50/..
48
1.71
0.0024
4.41
0.006
13
15
48
56 28 3,5 21 140 45 105 85 85
51
R.48 -Z 56/..-Z 56/..
38/45
0.89
0,0008
2.27
0.002
10
36
12
38
38
45
45 24
18 114 37
80 66 66
76 38
R.38/45-Z 45/..-Z 45/..
42/55
1.39
0.0018
3.57
0.005
12
40
14
42
42
55
50 26
20 126 40
95 75 75
94 46
R.42/55-Z 50/..-Z 50/..
48/60
1.86
0.0030
4.80
0.008
13
46
15
48
48
60
56 28 3.5 21 140 45 105 85 85 102 51
R.48/60-Z 56/..-Z 56/..
55/70
7.37
0.016
18
52
20
55
55
70
65 30
98 120 60
R.55/70-Z 65/..-Z 65/..
65/75
10.90
0.031
20
63
22
65
65
75
75 35 4.5 26 185 61 135
115 135 68
R.65/70-Z 75/..-Z 75/..
75/90
17.70
0.068
28
73
30
75
75
90
85 40
135 160 80
R.75/90-Z 85/..-Z 85/..
22 160 52 120
30 210 69 160
Medium temperature: -- 10 C up to + 80 C (intermittent temperature peaks up to + 120 C are permissible)

Weights and mass inertial torque are related to max. finished bore without groove
Finished bore based on ISO alignment H7; Keyway according to DIN 6885 Sheet 1
Motor with Pump KP 5 / . C.0. Z00 0DE .
Size
Motor 4-pole
Power
Speed
kW
1/min
Motor 6-pole
Power
Speed
kW
1/min
Bell housing
Coupling
160 M
160 L
11
15
1465
1465
7.5
11
960
960
PK 350 /10 /19
RA 38/45 Z45/38 Z45/42
180 M
180 L
18.5
22
1470
1470
15
970
PK 350 /10 /19
RA 42/55 Z50/38 Z50/48
200 LK
30
1470
18.5 / 22
975 / 975
PK 400 / 5 /7
RA 42/55 Z50/38 Z50/55
225 S
225 M
37
45
1480
1480
30
980
PK 450 / 3 / 23
RA 48/60 Z56/38 Z56/60
250 M
280 S
55
75
1480
1485
37
45
980
985
PL 550 / 1 / 9
PK 550 / 3 / 9
RG 55/70 Z65/38 Z65/65

RG 65/75 Z75/38 Z75/75
All motor dimensions and information refer to the ADDA motor make, other motor makes on request. Motor mounting IMB 35
Size
160
L1
200
L1
250
L1
300
L1
a1
160 - 300
f
g
160 MT
913
918
931
943
228
350
250
254
18
210
292
160 L
993
998
1011
1023
228
350
332
254
20
254
180 M
1033
1038
1051
1063
228
350
320
279
22
180 L
1033
1038
1051
1063
228
350
320
279
200 L
1093
1098
1111
1123
228
400
365
225 S
1177
1182
1195
1221
262
450
225 M
1177
1182
1195
1221
262
250 M
1255
1260
1273
1285
280 S
1390
1395
1408
1420
L2
w1
290
160
460
375
14
108
315
325
160
540
405
14
108
241
350
340
180
580
425
14
121
22
279
350
340
180
580
425
14
121
318
24
305
395
380
200
640
475
18
133
370
356
30
286
436
420
225
690
515
18
149
450
370
356
30
311
436
420
225
690
515
18
149
265
550
410
406
32
349
476
480
250
765
580
22
168
275
550
480
457
35
368
534
535
280
890
680
22
190
All pump and motor sizes can be combined with each other
10
Note
11
Product Portfolio
Transfer Pumps
Flow Measurement
Transfer pumps for lubricating oil

supply equipment, low pressure
filling and feed systems, dosing and
mixing systems.
Gear and turbine flow meters and

electronics for volume and flow metering
technology in hydraulics,
processing and laquering technology.
Mobile Hydraulics
Industrial Hydraulics /
Test Bench Construction
Single and multistage high pressure

gear pumps, hydraulic motors and
valves for construction machinery,
vehicle-mounted machines.
Cetop directional control and proportional

valves, hydraulic cylinders, pressure, quantity
and stop valves for pipe and slab construction,
hydraulic accessories for industrial hydraulics
(mobile and stationary use).
Technology Test benches / Fluid Test benches.
KP 5 / GB / 09.08
KRACHT GmbH Gewerbestr. 20 58791 Werdohl, Germany fon +49 (0) 23 92 / 935-0 fax +49 (0) 23 92 / 935 209
mail [email protected] web www.kracht.eu

Bomba de Engranajes Kracht KP5 - GB - 09-08

Uploaded by

Copyright:

Available Formats

Bomba de Engranajes Kracht KP5 - GB - 09-08

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bomba de Engranajes Kracht KP5 - GB - 09-08

Uploaded by

Copyright:

Available Formats

High Pressure Gear Pumps

High Pressure Gear Pumps KP 5

KP series high pressure gear pumps are mainly used

The housing components are made from high-grade

The shafts are supported in multi-layer bearings that

Shaft rotation clockwise: direction of conveyance

The use of fine-meshed filters significantly increases

High Pressure Gear Pumps KP 5

Calculation Formulas for Hydropumps

Characteristics, formula signs, units

1 Discharge / displacement flow

2 geom. discharge / displ. flow

Ambient temperature u min

9 hydr./ mech. efficiency

pe min = -- 0.4 bar (underpressure)

p max = Table, page 5

+ 120 C for FKM-

Lip-type shaft seal

Return line filter

Mineral oil based on

Products and media on request

Recommended values for KRACHT products

High Pressure Gear Pumps KP 5

Displacement / Nominal Size

High Pressure Gear Pumps KP 5

Discharge Flow and Required Input Power

Required input power P in kW at n = 950 1/min

Discharge flow at n = 1450 1/min

Required input power P in kW at n = 1450 1/min

Tolerance zone of the discharge flow: -- 5 % of table value Q.

High Pressure Gear Pumps KP 5

1 NBR lip-type shaft seal

Code for materials

Mounting equipment / Outboard bearing

High Pressure Gear Pumps KP 5

SAE-C-4 hole flange E,

High Pressure Gear Pumps KP 5

Housing side ports

High Pressure Gear Pumps KP 5

Gear rim off

Coupling hub length

Coupling hub length

R.38 -Z 45/..-Z 45/..

R.42 -Z 50/..-Z 50/..

56 28 3,5 21 140 45 105 85 85

R.48 -Z 56/..-Z 56/..

R.38/45-Z 45/..-Z 45/..

R.42/55-Z 50/..-Z 50/..

56 28 3.5 21 140 45 105 85 85 102 51

R.48/60-Z 56/..-Z 56/..

R.55/70-Z 65/..-Z 65/..

75 35 4.5 26 185 61 135

R.65/70-Z 75/..-Z 75/..

R.75/90-Z 85/..-Z 85/..

Medium temperature: -- 10 C up to + 80 C (intermittent temperature peaks up to + 120 C are permissible)

High Pressure Gear Pumps KP 5

Motor with Pump KP 5 / . C.0. Z00 0DE .

PK 350 /10 /19