Scribd Logo
Upload

Welcome to Scribd!

  • 143 views

    4G LTE Integration Training

    Uploaded by

    Abdirahman
    The document describes the process and steps for integrating a 4G LTE site including connecting the site via GPON, microwave or dark fiber and configuring the necessary network and system settings on the eNodeB equipment using the WEBLMT tool.

    Copyright:

    © All Rights Reserved
    Download as PPT, PDF, TXT or read online from Scribd

    4G LTE Integration Training

    Uploaded by

    Abdirahman
    143 views21 pages
    The document describes the process and steps for integrating a 4G LTE site including connecting the site via GPON, microwave or dark fiber and configuring the necessary network and system settings on the eNodeB equipment using the WEBLMT tool.

    Copyright

    © © All Rights Reserved

    Available Formats

    PPT, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes the process and steps for integrating a 4G LTE site including connecting the site via GPON, microwave or dark fiber and configuring the necessary network and system settings on the eNodeB equipment using the WEBLMT tool.

    Copyright:

    © All Rights Reserved
    Download as PPT, PDF, TXT or read online from Scribd
    Download as ppt, pdf, or txt
    143 views21 pages

    4G LTE Integration Training

    Uploaded by

    Abdirahman
    The document describes the process and steps for integrating a 4G LTE site including connecting the site via GPON, microwave or dark fiber and configuring the necessary network and system settings on the eNodeB equipment using the WEBLMT tool.

    Copyright:

    © All Rights Reserved
    Download as PPT, PDF, TXT or read online from Scribd
    Download as ppt, pdf, or txt
    of 21

    Security Level:

    4G LTE
    Integration
    www.huawei.com

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Types of site connectivity:


    1- GPON site.

    GE/FE Cable

    eNodeB

    2- Microwave site.

    GPON MDU (SmartAx)

    Fiber Cable

    eNodeB
    MW RTN900

    3- Dark Fiber site.

    Fiber Cable

    eNodeB
    Exchange OLT

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 2

    GPON connection

    GPON MDU (SmartAx)

    4G

    3G

    2G

    For 4G , 3G and 2G use FE/GE cable.

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 3

    Microwave Connection
    MW RTN950

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 4

    Microwave Connection
    EM6F Card of RTN950

    4G

    3G

    2G

    For 4G and 3G use LC to LC Fiber cable


    For 2G use FE/GE cable

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 5

    DF Connection
    Connect Fiber cable to ODF in
    Exchange site to the
    assigned Port ( you can know
    which port from JISOW
    sheet ).

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 6

    LTE BBU connection


    For MW and DF use SFP0 port , For GPON use FE0/GE0 Port

    or DF

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 7

    LTE 4G Integration
    Main Job on site:

    Use WEBLMT to login the eNodeB

    Add the OM link and check the link status

    Steps Of Job:

    Use WEBLMT to login the eNodeB

    Use the Ethernet cable to connect to ETH port of LMPT board.

    Configure the IP 192.168.0.2 on laptop.

    Use IE Browser and visit the website:

    http://192.168.0.49/

    Username admin

    Password admin123

    You must have JISOW sheet for IPs and VLAN

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 8

    1. SET DHCPSW: SWITCH=DISABLE;

    2. SET ETHPORT to modify as the picture below:

    GPON : Port Attribute =


    Copper
    MW : Port Attribute =
    Fiber

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 9

    3. DSP ETHPORT: SN=7, SBT=BASE_BOARD;

    To check port

    status
    DSP ETHPORT Result
    -----------------Cabinet No. = 0
    Subrack No. = 0
    Slot No. = 7
    Subboard Type = Base Board
    Port No. = 0
    Port Attribute = Copper
    Port Status = Up
    Physical Layer Status = Up
    Maximum Transmission Unit(byte) = 1500
    ARP Proxy = Enable
    Flow Control = Open
    MAC Address = 707B-E8C5-8B9A
    Loopback Status = No Loop
    In Loopback Mode or Not = No
    Ethernet OAM 3AH Flag = Disable
    Number of RX Packets(packet) = 444334
    Number of RX Bytes(byte) = 79380405
    Number of RX CRC Error Packets(packet) = 4
    RX Traffic(byte/s) = 257
    Number of TX Packets(packet) = 215850
    Number of TX Bytes(byte) = 40290597
    TX Traffic(byte/s) = 146
    Local Configuration Negotiation Mode = Automatic Negotiation
    Local Actual Negotiation Mode = Automatic Negotiation
    Local Speed = 1000M
    Local Duplex = Full Duplex
    Peer Actual Negotiation Mode = Unknown
    Peer Speed = 1000M
    Peer Duplex = Unknown
    Number of IPs = 2
    IP Address List = 10.226.5.193 255.255.255.252
    = 10.140.10.193 255.255.255.252
    (Number of results = 1)

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 10

    4. ADD DEVIP:;
    As picture below:

    0
    O&M Host IP in JISOW

    From JISOW

    5. ADD VLANMAP:;

    O&M DGW in JISOW

    From JISOW
    VLAN ID (OaM) in JISOW

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 11

    6. ADD OMCH:;

    O&M Host IP in JISOW


    From JISOW

    O&M DGW in JISOW

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 12

    7. Ping:;
    Tow destination:

    PING from Local IP to GW IP

    PING from Local IP to destination IP


    (172.20.110.127)

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 13

    Ping Result must be as follow:

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 14

    8. Copy the Script Below To Batch section and press


    GO and wait till finish.

    Script.txt

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 15

    9. ADD GPS: SN=7, CABLETYPE=COAXIAL,


    CABLE_LEN=45, PRI=1;

    10. SET CLKSYNCMODE: CLKSYNCMODE=TIME;

    Select Time

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 16

    11. DSP GPS: GN=0;


    * Make sure the GPS Card State is Normal; And the GPS
    Satellites Traced is larger than 8.

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 17

    12. STR VSWRTEST:;


    Be sure all VSWR values below 140

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 18

    At Last when every things Ok Call integration Team


    to make complete integration remotely after
    confirm to you status is ok you can leave site.

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 19

    Some Cases

    Ethernet Port wrong configured.

    Only can ping to GW but you cannot ping to Peer IP


    (M2000).

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 20

    Thanks

    HUAWEI TECHNOLOGIES CO., LTD.

    Huawei Confidential

    Page 21

    You might also like