XP170X

Preface
SIMATIC HMI
HMI device
TP 170micro, TP 170A, TP 170B,
OP 170B (WinCC flexible)
Operating Instructions
Order number 6AV6691-1DB01-0AB0
Edition 03/2004
A5E00280550-01
Overview
Safety instructions and

general notes
Planning use
Installation and connection
Operator control elements

and displays
Operating system and

configuration
Preparing and backing up a

project
Runtime functionalities of a
project
Operating a project
Operating recipes
10
Maintenance/Service
11
Specifications
12
Appendix
Abbreviations
Glossary
Safety Guidelines
This manual contains notices which you should observe to ensure your own personal safety as well as to avoid
property damage. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring to property damage only have no safety alert symbol.
Danger
indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Warning
indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Caution
used with the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Caution
used without safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
Notice
used without the safety alert symbol indicates a potential situation which, if not avoided, may result in
an undesirable result or state.
When several danger levels apply, the notices of the highest level (lower number) are always displayed. If a
notice refers to personal damages with the safety alert symbol, then another notice may be added warning of
property damage.
Qualified Personnel
The device/system may only be set up and operated in conjunction with this documentation. Only qualified
personnel should be allowed to install and work on the equipment. Qualified persons are defined as persons who
are authorized to commission, to earth, and to tag circuits, equipment and systems in accordance with
established safety practices and standards.
Intended Use
Please note the following:
Warning
This device and its components may only be used for the applications described in the catalog or
technical description, and only in connection with devices or components from other manufacturers
approved or recommended by Siemens.
This product can only function correctly and safely if it is transported, stored, set up and installed
correctly, and operated and maintained as recommended.
Trademarks
All designations marked with are registered trademarks of Siemens AG. Other designations in this
documentation might be trademarks which, if used by third parties for their purposes, might infringe upon the
rights of the proprietors.
Copyright Siemens AG, 2004. All rights reserved

Reproduction, transmission or use of this document or its contents is not permitted without
express written authority. Offenders will be liable for damages. All rights, including rights
created by patent grant or registration of a utility model or design, are reserved.
Disclaimer of Liability
We have checked the contents of this manual for agreement with the hardware and
software described. Since deviations cannot be precluded entirely, we cannot guarantee
full agreement. However, the data in the manual are reviewed regularly, and any
necessary corrections will be included in subsequent editions. Suggestions for
improvement are welcomed.
Siemens AG
Automation and Drives Group
P.O. Box 4848, D-90327 Nuremberg (Germany)
Siemens AG 2004
Technical data subject to change
Siemens Aktiengesellschaft
6AV6691-1DB01-0AB0
Preface
Purpose of this manual
This manual provides information based on the requirements defined by DIN 8418 regarding
mechanical engineering documentation. This information relates to the device, its place of
use, transport, storage, installation, use and maintenance.
This manual is intended for the following target groups:
Users
Commissioning engineers
Service technicians
Maintenance technicians
Please read carefully the section "Safety information and general notes".
The help integrated in WinCC flexible, the WinCC flexible Information System, contains
detailed information. The Information System contains instructions, examples and reference
information in electronic form.
Basic knowledge required

A general knowledge of automation technology and process communication is necessary in
order to understand the manual.
It is assumed users have good basic knowledge on the use of personal computers and MS
Windows operating systems.
Scope of the manual

The manual applies to the SIMATIC TP 170micro, TP 170A, TP 170B and OP 170B used in
connection with the WinCC flexible 2004 software packet.
TP 170micro, TP 170A, TP 170B, OP 170B (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DB01-0AB0
Preface
Placement in the information landscape

This manual is part of the SIMATIC HMI documentation. The information below presents an
overview of the information landscape of SIMATIC HMI.
User manual
WinCC flexible Micro:
Describes basic principles of configuration using the WinCC flexible Micro Engineering
System.
WinCC flexible Compact/Standard/Advanced:
Describes basic principles of configuration using the WinCC flexible Compact
Engineering System/WinCC flexible Standard/WinCC flexible Advanced
WinCC flexible Runtime:
Describes how to commission and operate your Runtime project on a PC.
WinCC flexible Migration:
Describes how to convert an existing ProTool project to WinCC flexible.
Describes how to convert an existing WinCC project to WinCC flexible.
Describes the conversion of ProTool projects together with changing the HMI device
from OP7 to OP 77B.
Describes the conversion of ProTool projects with a change in the HMI device from a
graphics device to a Windows CE device.
Communication:
Communication Part 1 describes the connection of the HMI device to SIMATIC PLCs.
Communication Part 2 describes the connection of the HMI device to third-party PLCs.
Operating instructions
Operating instructions for the SIMATIC OP 77B,
TP 170micro/TP 170A/TP 170B/OP 170B, SIMATIC Mobile Panel 170, SIMATIC
TP 270/OP 270/MP 270B, and SIMATIC MP 370 HMI devices.
Quick reference manuals for the SIMATIC OP 77B and SIMATIC Mobile Panel 170 HMI
devices.
Getting started
WinCC flexible for first time users:
Based on a sample project, this is a step-by-step introduction to the basics of
configuring screens, alarms, and recipes, and screen navigation.
WinCC flexible for advanced users:
configuring logs, project reports, scripts, user management, and multilingual projects,
and integration into STEP 7.
WinCC flexible options:
configuring the WinCC flexible Sm@rtServices, Sm@rtAccess and OPC Server
options.
ii

Preface
Online availability
The following links provide direct access to technical documentation on SIMATIC products
and systems in English, German, French, Italian, and Spanish.
SIMATIC Guide Technische Dokumentation in Deutsch:
http://www.ad.siemens.de/simatic/portal/html_00/techdoku.htm
SIMATIC Guide for Technical Documentation in English:
http://www.ad.siemens.de/simatic/portal/html_76/techdoku.htm
Conventions
The following applies with regard to the designation of the configuration and runtime
software:
"WinCC flexible 2004" refers to the configuration software.
"Runtime" designates the runtime software which can run on the HMI device.
The term "runtime" is also used during operation for projects on MS Windows CE HMI
devices.
"WinCC flexible Runtime" designates the visualization product for use on standard PCs or
panel PCs.
The term "WinCC flexible" is used in the general context. A version name such as
"WinCC flexible 2004" is used whenever it is necessary to distinguish it from other versions.
The following formatting is used to facilitate reading of the manual:
Notation
Scope
"Add screen"
Terminology that occurs in the user interface, e.g., dialog

names, tabs, buttons, menu commands.
Inputs required, e.g., limit values, tag values.
Path information
"File > Edit"
Operational sequences, e.g., menu commands/shortcut menu

commands.
<F1>, <Alt+P>
Keyboard inputs
Please observe notes labeled as follows:
Note
A note contains important information about the product, about the handling off the product,
or about a specific section of the documentation to which particular attention should be paid.

iii
Preface
Registered trademarks
All names designated with an are registered trademarks of Siemens AG.
HMI
SIMATIC
SIMATIC HMI
SIMATIC ProTool
SIMATIC WinCC
SIMATIC WinCC flexible
SIMATIC TP 170micro
SIMATIC TP 170A
SIMATIC TP 170B
SIMATIC OP 170B
The other designations in this manual may be trademarks whose use by third parties for their
own purposes could violate the rights of the owner.
Representatives and offices

If you have any further questions relating to the products described in this manual, please
contact your local representative at the SIEMENS branch nearest you.
You local representative can be found under:
http://www.siemens.com/automation/partner
Training center
To familiarize you with automation systems, we offer a variety of courses. Please contact
your regional training center, or the central training center in D-90327 Nuremberg.
Phone: +49 (911) 895-3200
Internet: http://www.sitrain.com
Service & support in the Internet

Service & Support offers comprehensive information on SIMATIC products online at
"http://www.siemens.com/automation/service&support":
The newsletter keeps you up-to-date with information relating to your products.
Our Service & Support search engine provides you with abundant documentation.
A bulletin board where users and experts exchange their knowledge worldwide.
Current product information, FAQs and downloads.
Your local contact for Automation & Drives.
Information about on-site services, repairs, spare parts and much more is available on
our "Services" pages.
iv

Preface
A&D Technical Support and Authorization

Available 24 hours worldwide:
Nuremberg
Johnson City
Beijing
SIMATIC Hotline
Worldwide (Nuremberg)
Worldwide (Nuremberg)
Technical Support
(Free Contact)
Technical Support
(fee-based, only with Automation Value Card)
Local time:
Mo.Fr. 7:00 to 17:00
Local time:
0:00 to 24:00, 365 days
Telephone:
+49 (0) 180 5050-222
Telephone:
+49 (911) 895 -7777
Fax:
+49 (0) 180 5050-223
Fax:
+49 (911) 895-7001
E-Mail:
[email protected]
E-mail:
GMT: +1:00
GMT: +1:00
Europe/Africa (Nuremberg)
America (Johnson City)
Asia/Pacific (Beijing)
Authorization
Technical Support and Authorization
Technical Support and Authorization
Local time:
Mo.Fr. 7:00 to 17:00
Local time:
Mon.Fri. 8:00 a.m. to 7:00 p.m.
Local time:
Mon.Fri. 8:30 a.m. to 5:30 p.m.
Telephone:
+49 (911) 895-7200
Telephone:
+1 423 461-2522
Telephone:
+86 (10) 64 75 75 75
Fax:
+49 (911) 895-7201
Fax:
+1 423 461-2289
Fax:
+86 (10) 64 74 74 74
E-Mail:
[email protected]
E-Mail:
[email protected]
E-mail:
[email protected]
GMT: +1:00
GMT: 5:00
GMT: +8:00
Information is available in German and English.

Preface
vi

Table of contents
Preface ........................................................................................................................................................i
1
Overview................................................................................................................................................. 1-1
1.1
Design of the TP 170micro HMI device ..................................................................................... 1-1
1.2
Design of the TP 170A HMI device............................................................................................ 1-2
1.3
Design of the TP 170B HMI device............................................................................................ 1-3
1.4
Design of the OP 170B HMI device ........................................................................................... 1-4
1.5
Accessories................................................................................................................................ 1-6
1.6
Miscellaneous ............................................................................................................................ 1-6
1.7
Functional scope of WinCC flexible on TP 170micro and TP 170A .......................................... 1-7
1.8
Functional scope of WinCC flexible on TP 170B and OP 170B ................................................ 1-9
1.9
Communication using TP 170micro ......................................................................................... 1-11
1.10
Communication using the TP 170A, TP 170B and OP 170B .................................................. 1-11
Safety instructions and general notes ..................................................................................................... 2-1

2.1
Safety instructions...................................................................................................................... 2-1
2.2
General notes............................................................................................................................. 2-2
Planning use........................................................................................................................................... 3-1

3.1
Installation notes ........................................................................................................................ 3-1
3.2
Installation position and fixation ................................................................................................. 3-2
3.3
Installation cut-out...................................................................................................................... 3-4
3.4
Transport.................................................................................................................................... 3-8
Installation and connection ..................................................................................................................... 4-1

4.1
Checking the shipment .............................................................................................................. 4-1
4.2
Installation of the HMI device..................................................................................................... 4-1
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
4.3.7
4.3.8
4.3.9
Connecting the HMI device........................................................................................................ 4-3

Interfaces on the TP 170micro, TP 170A and TP 170B ............................................................ 4-4
Interfaces on the OP 170B......................................................................................................... 4-5
Connecting the lines .................................................................................................................. 4-5
Connecting the equipotential bonding ....................................................................................... 4-5
Connecting the PLC................................................................................................................... 4-8
Connecting the configuration computer ................................................................................... 4-12
Connecting a TP 170B or OP 170B to peripheral equipment.................................................. 4-14
Connecting the power supply................................................................................................... 4-15
Switch on and test the HMI device........................................................................................... 4-17

vii
Table of contents
5
viii
Operator control elements and displays.................................................................................................. 5-1

5.1
Operating elements and indicators on the front of the TP 170micro, TP 170A and TP 170B ... 5-1
5.2
5.2.1
5.2.2
5.2.3
Other operator controls on the TP 170A and TP 170B.............................................................. 5-2

Using the memory card with the TP 170B ................................................................................. 5-2
Unplugging the memory card..................................................................................................... 5-3
Setting the DIL switch ................................................................................................................ 5-3
5.3
Front side operating elements and indicators on the OP 170B ................................................. 5-4
5.4
5.4.1
5.4.2
5.4.3
Other operating elements on the OP 170B................................................................................ 5-5

Using the memory card with the OP 170B................................................................................. 5-6
Labeling the OP 170B softkeys.................................................................................................. 5-7
Setting the DIL switch ................................................................................................................ 5-9
Operating system and configuration ....................................................................................................... 6-1

6.1
6.1.1
6.1.2
Configuring the TP 170micro and TP 170A operating system................................................... 6-1

Operating by touch..................................................................................................................... 6-2
"Control Settings" dialog ............................................................................................................ 6-3
6.2
6.2.1
6.2.2
6.2.2.1
6.2.2.2
6.2.3
6.2.4
6.2.5
6.2.6
6.2.7
6.2.8
6.2.9
6.2.10
6.2.11
6.2.12
6.2.13
6.2.14
Configuring the operating system for TP 170B and OP 170B ................................................... 6-5
Operating by touch..................................................................................................................... 6-6
Navigating and operating ........................................................................................................... 6-6
Operating and navigating in Control Panel ................................................................................ 6-7
Operating and navigating in a dialog ....................................................................................... 6-10
Backup/Restore........................................................................................................................ 6-13
Communications Properties ..................................................................................................... 6-14
Date/Time................................................................................................................................. 6-15
InputPanel ................................................................................................................................ 6-16
Keyboard .................................................................................................................................. 6-20
Mouse....................................................................................................................................... 6-21
OP ............................................................................................................................................ 6-23
Password ................................................................................................................................. 6-26
Printer....................................................................................................................................... 6-28
Regional Settings ..................................................................................................................... 6-30
Screen Saver ........................................................................................................................... 6-33
System ..................................................................................................................................... 6-34
6.3
Touchscreen calibration ........................................................................................................... 6-35
6.4
Configuring transfer mode for the TP 170A ............................................................................. 6-37
6.5
6.5.1
6.5.2
Configuring transfer mode for the TP 170B and OP 170B ...................................................... 6-40
S7-Transfer Settings ................................................................................................................ 6-40
Transfer .................................................................................................................................... 6-42
6.6
Runtime .................................................................................................................................... 6-45
Preparing and backing up a project ........................................................................................................ 7-1

7.1
7.1.1
7.1.2
7.1.3
7.1.4
Transferring a project to an HMI device..................................................................................... 7-1

Overview .................................................................................................................................... 7-1
Initial commissioning .................................................................................................................. 7-2
Recommissioning....................................................................................................................... 7-3
Setting the operating mode ........................................................................................................ 7-3
7.2
7.2.1
7.2.2
7.2.3
7.2.4
Transfer ...................................................................................................................................... 7-4

Information and overview ........................................................................................................... 7-4
Start transfer .............................................................................................................................. 7-6
Testing project............................................................................................................................ 7-8
Transferring a project back using the TP 170B and OP 170B................................................. 7-10

Table of contents
7.3
7.3.1
7.3.2
Backup and restore project for TP 170B and OP 170B on memory card................................ 7-12
Overview .................................................................................................................................. 7-12
Backup and restore project ...................................................................................................... 7-13
7.4
7.4.1
7.4.2
7.4.3
7.4.4
ProSave ................................................................................................................................... 7-15

Overview .................................................................................................................................. 7-15
Backup project ......................................................................................................................... 7-16
Restore project......................................................................................................................... 7-18
Updating the operating system ................................................................................................ 7-19
Runtime functionalities of a project ......................................................................................................... 8-1

8.1
Screen objects ........................................................................................................................... 8-1
8.2
Alarms ........................................................................................................................................ 8-2
8.3
Tags ........................................................................................................................................... 8-3
8.4
System functions........................................................................................................................ 8-3
8.5
Safety ......................................................................................................................................... 8-4
8.6
Other operating functions........................................................................................................... 8-7
Operating a project ................................................................................................................................. 9-1

9.1
9.1.1
9.1.2
9.1.2.1
9.1.2.2
9.1.2.3
9.1.2.4
9.1.2.5
9.1.3
9.1.3.1
9.1.3.2
9.1.3.3
9.1.4
Basic principles of operation ...................................................................................................... 9-1

Basics for operation in Runtime ................................................................................................. 9-1
Operating the touch screen device ............................................................................................ 9-3
Operating touch objects ............................................................................................................. 9-3
Input of values............................................................................................................................ 9-4
Inputting numeric values ............................................................................................................ 9-5
Inputting alphanumeric values ................................................................................................... 9-6
Opening an operator note (TP 170B and OP 170B only) .......................................................... 9-7
Operating a keyboard device ..................................................................................................... 9-8
Functions of the system keys..................................................................................................... 9-8
Functions of the key combinations............................................................................................. 9-9
Calling the operator note.......................................................................................................... 9-11
Close the project. ..................................................................................................................... 9-12
9.2
9.2.1
9.2.1.1
9.2.1.2
9.2.1.3
9.2.2
9.2.2.1
9.2.2.2
9.2.2.3
9.2.3
9.2.3.1
9.2.3.2
9.2.3.3
9.2.4
9.2.4.1
9.2.4.2
9.2.4.3
9.2.5
9.2.5.1
9.2.5.2
9.2.5.3
9.2.6
Operating graphic objects ........................................................................................................ 9-12

Button....................................................................................................................................... 9-12
Description ............................................................................................................................... 9-12
Touch control ........................................................................................................................... 9-13
Keyboard control...................................................................................................................... 9-13
Switch....................................................................................................................................... 9-13
Description ............................................................................................................................... 9-13
Touch control ........................................................................................................................... 9-14
IO field...................................................................................................................................... 9-14
Description ............................................................................................................................... 9-14
Touch control ........................................................................................................................... 9-15
Graphic IO field ........................................................................................................................ 9-16
Description ............................................................................................................................... 9-16
Touch control ........................................................................................................................... 9-17
Symbolic IO field ...................................................................................................................... 9-18
Description ............................................................................................................................... 9-18
Touch control ........................................................................................................................... 9-18
Alarm indicator (TP 170B and OP 170B only) ......................................................................... 9-19

ix
Table of contents
9.2.6.1
9.2.6.2
9.2.7
9.2.7.1
9.2.7.2
9.2.7.3
9.2.8
9.2.8.1
9.2.8.2
9.2.8.3
9.2.9
9.2.10
9.2.10.1
9.2.10.2
9.2.10.3
9.2.11
9.2.11.1
9.2.11.2
9.2.11.3
9.2.12
9.2.12.1
9.2.12.2
9.2.12.3
9.2.13
9.2.13.1
9.2.13.2
9.2.13.3
10
Description ............................................................................................................................... 9-19

Touch control ........................................................................................................................... 9-20
Alarm view (TP 170B and OP 170B only)................................................................................ 9-20
Description ............................................................................................................................... 9-20
Touch control ........................................................................................................................... 9-21
Keyboard control ...................................................................................................................... 9-21
Simple alarm view .................................................................................................................... 9-22
Description ............................................................................................................................... 9-22
Touch control ........................................................................................................................... 9-23
Bar............................................................................................................................................ 9-24
Trend view (TP 170B and OP 170B only)................................................................................ 9-25
Description ............................................................................................................................... 9-25
Touch control ........................................................................................................................... 9-26
Date/time field .......................................................................................................................... 9-27
Description ............................................................................................................................... 9-27
Touch control ........................................................................................................................... 9-27
User view (TP 170B and OP 170B only).................................................................................. 9-28
Description ............................................................................................................................... 9-28
Touch control ........................................................................................................................... 9-29
Simple user view (TP 170B and OP 170B only) ...................................................................... 9-30
Description ............................................................................................................................... 9-30
Touch control ........................................................................................................................... 9-31
Operating recipes ................................................................................................................................. 10-1

10.1
Structure of a recipe................................................................................................................. 10-1
10.2
Structure of a recipe data record ............................................................................................. 10-2
10.3
Recipe in the project ................................................................................................................ 10-3
10.4
10.4.1
10.4.2
Display recipes......................................................................................................................... 10-5

Display and edit recipe............................................................................................................. 10-5
Behavior of the recipe view ...................................................................................................... 10-7
10.5
10.5.1
10.5.2
10.5.3
Recipe view (TP 170B and OP 170B only) .............................................................................. 10-7

Description ............................................................................................................................... 10-7
Touch control ........................................................................................................................... 10-8
10.6
10.6.1
10.6.2
10.6.3
Simple recipe view (TP 170B and OP 170B only) ................................................................. 10-10
Description ............................................................................................................................. 10-10
Touch control ......................................................................................................................... 10-11
Keyboard control .................................................................................................................... 10-11
10.7
10.7.1
10.7.2
10.7.3
10.7.4
10.7.5
Operating recipe data record ................................................................................................. 10-12

Recipe data record administration ......................................................................................... 10-12
Synchronizing a recipe data record ....................................................................................... 10-14
Read recipe data record from PLC ........................................................................................ 10-14
Transfer recipe record to PLC................................................................................................ 10-15
Exporting and importing recipe data records ......................................................................... 10-15

Table of contents
11
12
Maintenance/Service ............................................................................................................................ 11-1

11.1
11.1.1
11.1.2
Maintenance and service ......................................................................................................... 11-1

Clean screen ............................................................................................................................ 11-2
Protective foil and protective cover.......................................................................................... 11-2
11.2
Servicing and spare parts ........................................................................................................ 11-6
Specifications ....................................................................................................................................... 12-1

12.1
Dimensioned drawings of the TP 170micro, TP 170A and TP 170B....................................... 12-1
12.2
Dimensioned drawings of the OP 170B................................................................................... 12-2
12.3
Technical data, TP 170micro, TP 170A and TP 170B............................................................. 12-2
12.4
Technical data, OP 170B ......................................................................................................... 12-4
12.5
Ambient conditions................................................................................................................... 12-5
12.6
EMC requirements ................................................................................................................... 12-7
12.7
12.7.1
12.7.2
12.7.3
12.7.4
Description of interfaces .......................................................................................................... 12-8

Power supply............................................................................................................................ 12-8
RS 422/RS 485 (IF 1B) ............................................................................................................ 12-8
RS 232 (IF 1A) ......................................................................................................................... 12-9
RS 232 (IF 2)............................................................................................................................ 12-9
Appendix.................................................................................................................................................A-1
A.1
A.1.1
A.1.2
Certificates and guidelines......................................................................................................... A-1

Approvals ................................................................................................................................... A-1
ESD guidelines .......................................................................................................................... A-2
A.2
System alarms ........................................................................................................................... A-4
Abbreviations..........................................................................................................................................B-1
Glossary .................................................................................................................................................C-1
Index

xi
Table of contents
Tables
Table 1-1
Functional scope of alarms using TP 170micro and TP 170A................................................... 1-7
Table 1-2
Functional scope of tags, values, lists and calculation functions using the TP 170micro and TP
170A ........................................................................................................................................... 1-7
Table 1-3
Functional scope of screens using TP 170micro and TP 170A ................................................. 1-8
Table 1-4
Functional scope of supplementary functions using TP 170micro and TP 170A ...................... 1-8
Table 1-5
Functional scope of alarms using TP 170B and OP 170B......................................................... 1-9
Table 1-6
Functional scope of tags, values, lists and calculation functions using the TP 170B and OP
170B ........................................................................................................................................... 1-9
Table 1-7
Functional scope of screens and recipes using TP 170B and OP 170B ................................. 1-10
Table 1-8
Functional scope of operator notes using TP 170B and OP 170B .......................................... 1-10
Table 1-9
Additional functions using TP 170B and OP 170B .................................................................. 1-10
Table 1-10
Number of connectable PLCs .................................................................................................. 1-11
Table 1-11
Connectable Siemens PLCs and available profiles ................................................................. 1-11
Table 1-12
Number of connectable PLCs .................................................................................................. 1-11
Table 1-13
Connectable Siemens PLCs and available reports or profiles................................................. 1-11
Table 1-14
Connectable PLCs from other manufacturers and protocols for use....................................... 1-12
Table 4-1
DIL switch settings on the TP 170A, TP 170B and OP 170B .................................................. 4-11
Table 6-1
Keys for navigating in the Control Panel at the OP 170B .......................................................... 6-8
Table 6-2
Keys for the navigation in a dialog of the "Control Panel" using the OP 170B ........................ 6-11
Table 12-1
Permissible ambient conditions ............................................................................................... 12-5
Table 12-2
Permissible mechanical ambient conditions ............................................................................ 12-6
Table 12-3
Testing mechanical ambient conditions ................................................................................... 12-6
Table A-1
HMI device approvals.................................................................................................................A-1
xii

Overview
1.1
Design of the TP 170micro HMI device
Figure 1-1
Front view and side view
Construction-related opening not a slot for a memory card
Display / Touchscreen
Installation seal
Recess for spring terminal
Figure 1-2
Bottom view
Connection for the power supply
Data interface

1-1
Overview
1.2 Design of the TP 170A HMI device
1.2
Design of the TP 170A HMI device
Figure 1-3
Construction-related opening not a slot for a memory card
Installation seal
Figure 1-4
1-2
Bottom view
Data interfaces

Overview
1.3 Design of the TP 170B HMI device
1.3
Design of the TP 170B HMI device
Figure 1-5
Memory card slot for a CF card
Installation seal
Figure 1-6
Bottom view
Data interfaces

1-3
Overview
1.4 Design of the OP 170B HMI device
1.4
Design of the OP 170B HMI device
Figure 1-7
1-4
Front view
Display
Membrane keyboard

Overview
1.4 Design of the OP 170B HMI device
Figure 1-8
Side view
Memory card slot for a CF card
Installation seal
1
Figure 1-9
Bottom view
Data interfaces

1-5
Overview
1.5 Accessories
1.5
Accessories
Accessory kit
The accessory kit contains the following:
A terminal block for the power supply
Four spring terminals for installing the TP 170micro, TP 170A and TP 170B
Six spring terminals for installing an OP 170B
Memory card
For the TP 170B and OP 170B:
The memory card is an option.
A commercially available CF memory card (Compact Flash, Type 1) can be used as an
external storage medium. A CF card which has been tested and approved is available from
Siemens AG.
1.6
Miscellaneous
PC-PPI adapter
For TP 170micro:
To enable RS 485/RS 232 switching, the PC-PPI adapter, Order No.: 6ES7 901-3CB300XA0, can be ordered from Siemens AG.
Protective foil and protective cover

A protective foil is available for the HMI devices TP 170micro, TP 170A and TP 170B, order
no.: 6AV6 574-1AD00-4AX0 and a protective cover, order no.: 6AV6 574-1AE00-4AX0
available.
Labeling strips
For the OP 170B:
Labeling strips are available as an optional accessory. They can also be made from a
supplied template. The template is available for use after installing WinCC flexible on the
installation computer and on the "WinCC flexible" installation CD under
...\Documents\slide170b.doc.
See also
Labeling the OP 170B softkeys (Page 5-7)
1-6

Overview
1.7 Functional scope of WinCC flexible on TP 170micro and TP 170A
1.7
Functional scope of WinCC flexible on TP 170micro and TP 170A
General
The following tables show the objects which can be integrated in a project for a TP 170micro
and TP 170A. Each object is categorized according to the maximum number the HMI device
can manage or its method of operation.
Alarms
Table 1-1
Functional scope of alarms using TP 170micro and TP 170A
Object
Specification
Alarm
TP 170micro
Number of discrete alarms
TP 170A
500
1000
Length of alarm text per line
80
Number of tags in an alarm
Display
Alarm view, alarm window
View all pending alarms
Alarm view
Acknowledge single error alarms
Yes
Acknowledge several error alarms simultaneously

(group acknowledgement)
Yes
Edit alarm
Yes
ALARM_S
Display S7 alarms
No
Volatile alarm buffer
Alarm buffer capacity
128 alarm events
Simultaneously queued alarm events
Max.16
View alarm
Yes
Delete alarm
Yes
Tags, values, lists and calculation functions

Table 1-2
Functional scope of tags, values, lists and calculation functions using the TP 170micro and TP 170A
Object
Specification
Tag
Number1)
Limit-value monitoring
Input/output
1)
TP 170micro
TP 170A
250
500
Yes
Maximum total number for PowerTags and internal tags

1-7
Overview
1.7 Functional scope of WinCC flexible on TP 170micro and TP 170A
Screens
Table 1-3
Functional scope of screens using TP 170micro and TP 170A

Object
Specification
Screen
TP 170micro
TP 170A
Number
250
Fields per screen
20
Tags per screen
20
Complex objects per screen (e.g. bars)
Templates
Yes
The functional scope is also restricted by the size of the internal Flash memory.
Additional functions
Table 1-4
Functional scope of supplementary functions using TP 170micro and TP 170A

Object
Display settings
Specification
TP 170micro
Contrast
Yes
Touchscreen calibration
Yes
Language switching
Number of languages
Trend
Number
Graphic object
Number
500
Text object
Number
500
Password protection
Number of passwords
Scheduler
Trigger functions cyclically or once
1-8
TP 170A
5
No
1000
1000
1
No

Overview
1.8 Functional scope of WinCC flexible on TP 170B and OP 170B
1.8
Functional scope of WinCC flexible on TP 170B and OP 170B
General
The following tables contain objects that can be integrated in a project for a TP 170B and OP
170B. Each object is specified according to the maximum number the TP 170B or the OP
170B can manage or its method of operation.
Alarms
Table 1-5
Functional scope of alarms using TP 170B and OP 170B

Object
Specification
Alarm
TP 170B
OP 170B
Number of discrete alarms
2000
Number of analog alarms
50
Length of alarm text per line
80
Number of tags in an alarm

Display
8
Alarm view, alarm window
View all pending alarms
Alarm view
Acknowledge single error alarms

Acknowledge several error alarms simultaneously
(group acknowledgement)
Yes
16 acknowledgment groups
Edit alarm
Yes
ALARM_S
Display S7 alarms
Yes
Alarm reporting
Output to printer
Volatile alarm buffer
Alarm buffer capacity
Yes
256 alarms
Simultaneously queued alarm events
max. 64
View alarm
Yes
Delete alarm
Yes
Print alarm line by line
Yes
Tags, values, lists and calculation functions

Table 1-6
Functional scope of tags, values, lists and calculation functions using the TP 170B and OP 170B
Object
Specification
TP 170B
OP 170B
Tag
Number1)
1000
Limit-value monitoring
Input/output
Yes
Conversion functions
Input/output
Yes
1)
Maximum total number for PowerTags and internal tags

1-9
Overview
1.8 Functional scope of WinCC flexible on TP 170B and OP 170B
Screens and recipes

Table 1-7
Functional scope of screens and recipes using TP 170B and OP 170B

Object
Specification
Screen
TP 170B
Number
500
Fields per screen
50
Tags per screen
50
Complex objects per screen (e.g. bars)
Recipe
OP 170B
Display screen
Yes
Print screen as hard copy
Yes
Templates
Yes
Number
100
Data records per recipe
200
Entries per recipe
200
The functional scope is restricted by the size of the internal Flash memory. In the case of
recipes, the number of data records can be increased by using a memory card.
Operator note
Table 1-8
Functional scope of operator notes using TP 170B and OP 170B

Object
Operator note
Specification
Lines/characters
TP 170B
OP 170B
7/35 using font "Tahoma"
For alarms
Yes
For screens
Yes
For screen objects (e.g. buttons)
Yes
Additional functions
Table 1-9
Additional functions using TP 170B and OP 170B

Object
Display settings
Specification
TP 170B
Contrast
OP 170B
Yes
Yes
No
Language switching
Number of languages
Trend
Number
50
Graphic object
Number
1000
Text object
Number
2500
Password protection
Number of passwords
50
Scheduler
Trigger functions cyclically or once
10
1-10

Overview
1.9 Communication using TP 170micro
1.9
Communication using TP 170micro

A certain number of PLCs can be connected to the HMI device.
Table 1-10
Number of connectable PLCs
Connectable controllers
TP 170micro
Number using a point-to-point connection
The HMI device can be connected to the following PLC families.
1.10
Table 1-11
Connectable Siemens PLCs and available profiles
Controller
Profile
SIMATIC S7-200
PPI
MPI
Communication using the TP 170A, TP 170B and OP 170B

A certain number of PLCs can be connected to the HMI device.
Table 1-12
Number of connectable PLCs
TP 170A
TP 170B
Number using a point-to-point connection
OP 170B
Number using a bus connection
4 on the same bus
The following tables list the PLC families that can be connected to the HMI device.
Table 1-13
Connectable Siemens PLCs and available reports or profiles
Controller
Report/Profile
TP 170A
TP 170B
OP 170B
SIMATIC S5
AS 511 via converter 1)
Yes
Yes
Yes
PROFIBUS DP up to 12 Mbaud
No
Yes
Yes
PROFIBUS DP up to 1,5 Mbaud
No
Yes
Yes
PPI
Yes
Yes
Yes
MPI
Yes
Yes
Yes
PROFIBUS DP CPU 215
Yes
Yes
Yes
PROFIBUS DP standard
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
PROFIBUS DP up to 1,5 Mbaud
Yes
Yes
Yes
NITP
Yes
Yes
Yes
No
Yes
Yes
SIMATIC S7-200
SIMATIC S7-300/400 MPI
SIMATIC 500/505
1)
The converter is optional.

1-11
Overview
1.10 Communication using the TP 170A, TP 170B and OP 170B
Table 1-14
1-12
Connectable PLCs from other manufacturers and protocols for use
Controller
Protocol
Allen-Bradley
PLC series SLC500, SLC501, SLC502, SLC503,
SLC504, SLC505, MicroLogix
DF1
DH+ using DF1-Gateway
DH485 using DF1 Gateway
DH485
Allen-Bradley
PLC series PLC5/20
DF1
DH+ using DF1-Gateway
GE Fanuc Automation
PLC series 90-30, 90-70, 90-Micro
SNP
LG Industrial Systems (Lucky Goldstar)/IMO

PLC series GLOFA-GM/G4, G6, G7M
Dedicated communication
Mitsubishi Electric
PLC series MELSEC FX, MELSEC FX0
FX
Mitsubishi Melsec
PLC series FX, A, Ans, Q, QnAS
Protocol 4
OMRON
PLC series SYSMAC C, SYSMAC CV, SYSMAC CS1,
SYSMAC alpha, CP
Hostlink/Multilink (SYSMAC Way)
Schneider Automation (Modicon)

PLC series Modicon 984, TSX Quantum, TSX Compact
Modicon Modbus

Safety instructions and general notes

2.1
Safety instructions
Work on the cabinet

Warning
Danger, high voltage
Opening the cabinet will expose high voltage parts. Contact with these parts could be fatal.
Switch off the power supply to the cabinet before opening it.
High frequency radiation

Notice
Exceptional operating situations
High frequency emissions, from mobile phones for example, can cause exceptional
operating situations.

2-1
Safety instructions and general notes

2.2 General notes
2.2
General notes
Industrial use
The HMI device is designed for industrial use. The following standards are met:
Requirements for emitted interference in EN 61000-6-4: 2001
Requirements for noise immunity in EN 61000-6-2: 2001
Residential use
If the HMI device is used in a residential area, you must take measures to achieve limit class
B in accordance with EN 55011 for radio interference emissions.
Suitable measures to achieve limit class B for suppression of radio interference include:
Installation of the HMI device in a grounded control cabinet
Use of filters in electrical supply lines
2-2

Planning use
3.1
Installation notes
Electromagnetic compatibility
The HMI device fulfills the requirements stipulated in the EMC law of the Federal Republic of
Germany as well as the EMC guidelines of the European Union.
Installation in grounded metal cabinets, e.g. 8 MC cabinet complying to Siemens catalog
NV21, ensures compliance to EN 61000-4-2.
Further information on EMC requirements can be found under "EMC requirements".
Installing HMI devices conform to EMC requirements

Conditions for error-free operation include a PLC design that conforms to EMC requirements
and the use of interference-proof cables. The "guidelines for interference-free construction of
PLCs" and the "PROFIBUS network" manual apply for the installation of the HMI device.
Conditions for use

The HMI device is intended for installation in weatherproof, permanent locations. The
conditions under which the device can be used exceed the requirements set out in DIN IEC
60721-3-3:
Class 3M3 (mechanical requirements)
Class 3K3 (climatic requirements)

3-1
Planning use
3.2 Installation position and fixation
Use with additional measures

Examples of applications where the use of the HMI device requires additional measures are:
In locations with a high degree of ionizing radiation
In locations with extreme operating conditions resulting from situations such as the
following:
Corrosive vapors or gases
Strong electric or magnetic fields
In systems which require special monitoring facilities - e.g.:
elevator systems
In particularly hazardous locations
The HMI device may be installed in a cabinet as an additional measure.
Note
Protective cover
The protective cover provides protection against dust, splashing water and corrosive vapors.
See also
EMC requirements (Page 12-7)
3.2
Installation position and fixation
Installation position
The HMI device is designed for installation in racks, cabinets, front panels and consoles. In
the following, all the installation options are referred to by the general term "cabinet".
The HMI device is self-ventilated and approved for vertical and inclined installation in
stationary cabinets.
+
Figure 3-1
3-2
Installation locations of the TP 170micro, TP 170A and TP 170B

Planning use
3.2 Installation position and fixation
Figure 3-2
Installation locations of the OP 170B
Installation position
Max. permissible ambient temperature
Max. 35 installation angle
40 C
vertical
50 C
Max. +35 installation angle
40 C
If the device is installed horizontally and the permissible ambient temperature is exceeded,
external ventilation is necessary. In general, ambient temperatures in excess of 50 C are
not permitted.
Caution
If the HMI device is operated above the maximum permissible ambient temperature without
external ventilation, the HMI device could be damaged. All the approvals stipulated in the
"Approvals" section become void and the terms of warranty are annulled.

3-3
Planning use
3.3 Installation cut-out
Type of fixation
Spring terminals are provided for the installation. These must be hooked into the recesses in
the HMI device. The overall HMI device dimensions are not exceeded by this.
1
2
Figure 3-3
3.3
View of a spring terminal
Hook
Recessed head screw
Installation cut-out
Consider the following when selecting the installation location:
The ambient conditions of the installation location must comply to those specified in the
section "Ambient conditions".
The requirements, based on EMC laws and EMC guidelines, must be fulfilled by the
installation location.
Danger
Installation location
Not every installation location can be selected without any additional measures. Some
installation locations will require additional measures be taken during installation.
Notice
If the HMI device will be exposed to vibration and impacts exceeding the ratings in the
specifications, appropriate measures must be taken, for example, installation of shock
absorbers.
3-4

Planning use
Selecting installation location

Caution
The HMI device is only approved for operation in closed enclosures.
Observe the following when selecting the location for the installation cut-out:
Position the HMI device so that the display is not exposed to direct sunlight or other
sources of light.
Position the HMI device so that it is ergonomically favorable for the user. For example,
select a suitable installation height.
Ensure the air vents are not covered following installation.
Ensure sufficient air low around the HMI device.
Observe the permissible installation position when installing the HMI device.
Producing the installation cut-out

Caution
The system's ability to be waterproof and dustproof as per the section "Approvals" is only
guaranteed when the following are met:
Material thickness of installation cut-out: 2 to 6 mm

Deviation of the installation cut-out from the horizontal based on the overall dimensions of the HMI
device: 0.5 mm
Permissible surface roughness in the area of the seal: 120 m (Rz 120)

3-5
Planning use
The required installation cut-out is illustrated in the following diagram:
142 1
198 1
Figure 3-4
Installation cut-out for the TP 170micro, TP 170A and TP 170B
241 1
229 1
Figure 3-5
3-6
Installation cut-out for the OP 170B

Planning use
Space
50
The HMI device must have sufficient space surrounding it:
15
50
15
Space around the TP 170micro and TP 170A
50
Figure 3-6
70
50
15
Figure 3-7
Space around the TP 170B

3-7
50
Planning use
3.4 Transport
70
15
15
Figure 3-8
Space around the OP 170B
At least 10 mm space is required at the back.
Notice
Ensure there is sufficient air circulation in the cabinet for cooling.
3.4
Transport
Notice
Ensure that no condensation develops on or in the HMI device after it has been transported
at low temperatures or it has been exposed to extreme temperature fluctuations.
The HMI device must be at room temperature before it is switched on. When doing so, do
not expose the HMI device to direct radiation from a heater. If condensation should occur,
only switch on the HMI device after waiting approximately 4 hours.
Conditions for problem-free, reliable operation of the HMI device include proper transport
and storage, installation, and assembly as well as careful operation and maintenance.
Failure to meet these requirements voids the rights to claims under the terms of warranty.
3-8


4.1
Checking the shipment

Check the packing contents for visible signs of transport damage and for completeness.
Notice
Do not install parts damaged during shipment. In the case of damaged parts, contact your
Siemens representative.
Keep the documentation supplied. This belongs to the HMI device and may be required
when commissioning in the future.
4.2
Installation of the HMI device
Requirement
To complete the installation, four spring terminals are required from the accessories for the
TP 170micro, TP 170A and TP 170B and six spring terminals are required for the OP 170B.
The installation seal must be mounted on the HMI device. If the installation seal is damaged,
order a replacement.
Installation
Notice
Only install the HMI devices according to the instructions in this manual.
Proceed as follows:
1. Check that the installation seal is fitted on the HMI device.
Do not mount the installation seal turned inside out. This can lead to gaps in the
installation cut-out.
2. Insert the HMI device in the installation cut-out from the front.

4-1

4.2 Installation of the HMI device
3. Insert the spring terminals in the recesses on the side of the HMI device.
Figure 4-1
Inserting the spring terminals in the TP 170micro, TP 170A and TP 170B
Four spring terminals must be installed and secured.
Figure 4-2
Inserting the spring terminals in the OP 170B
Four spring terminals must be installed and secured.

1. Secure the spring terminals by tightening the recessed head screws - 0.4 - 0.45 Nm is the
permissible torque.
Notice
Check the fit of the installation seal on the front side. This must not protrude from the HMI
device.
Otherwise, repeat steps working steps 1 to 4.
4-2


4.3 Connecting the HMI device
4.3
Connecting the HMI device
Requirement
The following condition must be fulfilled before the HMI device is connected electrically:
The HMI device must be installed according to the information provided in these
operating instructions.
Electrical connections
Connect the HMI device in the following sequence:
1. Potential equalization line
2. Controller
3. Configuration computer as necessary
4. Peripheral equipment as necessary
5. Supply voltage
Notice
Connection sequence
Carefully follow the sequence of HMI device connections. Failure to do so may result in
damage to the HMI device.
When disconnecting, it is essential that you follow the sequence in reverse order.

4-3

4.3.1
Interfaces on the TP 170micro, TP 170A and TP 170B

The following interfaces are available on the HMI device:
Figure 4-3
Interfaces on the TP 170micro
Figure 4-4
Interfaces on the TP 170A
Figure 4-5
Interfaces on the TP 170B
Chassis terminal
RS 422/RS 485 interface (IF 1B)

For TP 170micro: RS 485 interface (IF 1B)
4-4
RS 232 interface (IF 1A)
RS 232 interface (IF 2)


4.3.2
Interfaces on the OP 170B

The following interfaces are available on the HMI device:
1
Figure 4-6
4.3.3
Interfaces on the OP 170B
Chassis terminal
RS 422/RS 485 interface (IF 1B)
RS 232 interface (IF 1A)
RS 232 interface (IF 2)
Connecting the lines

When connecting the cables, ensure that the contact pins are not bent. Secure the cable
plugs with screws.
The pin assignment of the interfaces is described in the Technical Data.
4.3.4
Connecting the equipotential bonding
Potential difference
Differences in potential can occur between separated system parts and result in high
equalizing currents. This can happen when line shields are applied on both sides and
grounding occurs on different system parts.
The cause of potential differences can be different supply connections.

4-5

General requirements for equipotential bonding

Potential differences must be reduced by laying sufficient equipotential bonding cables to
ensure problem-free operation of the electronic components concerned. Therefore, the
following must be observed when setting up equipotential bonding:
The effectiveness of the equipotential bonding increases as the the impedance of the
equipotential bonding cables decreases (i.e., or as the cross section of the equipotential
bonding cable increases).
If two system parts are connected to each other via shielded data lines with shielding
connected to the grounding/protective conductor on both sides, the impedance of the
additionally laid equipotential bonding cables must not exceed 10% of the shield
impedance.
The cross-section of an equipotential bonding cable must be selected to accommodate
the maximum equalizing current flow. In practice, equipotential bonding cables between
control cabinets with a minimum cross-section of 16 mm2 have proven sufficient.
Use equipotential bonding cables made of copper or galvanized steel. Connect the
equipotential bonding cables properly to the grounding/protective conductor with the
greatest possible surface area and protect them from corrosion.
Clamp the shielding of the data line on the HMI device flush and as close as possible to
the potential equalization rail using cable clips.
Lay the potential equalization and data lines parallel to each other and within the
minimum distance of each other (refer to following Figure, Point 6).
Notice
Equipotential bonding cable
Cable shields are not suitable for equipotential bonding. Use only the prescribed
equipotential bonding cables. Potential cable, for example, must have a minimum crosssection of 16 mm. When setting up MPI and PROFIBUS DP networks, ensure cables
with a sufficient crosssection are used otherwise the interface modules may be damaged
or even destroyed.
4-6


Connection configurator
1
16
Equipotential bonding
Data cable, shielded
Figure 4-7
Installing equipotential bonding on the TP 170micro, TP 170A, TP 170B or OP 170B
Grounding connection on the HMI device
Control cabinet
Voltage bus
Cable clip
Ground connection
Parallel laying of equipotential bonding cable and data line

4-7

4.3.5
Connecting the PLC
The following diagram illustrates the connection between the HMI device and PLC.
SIMATIC S7-200
RS 485
Figure 4-8
Connecting a PLC to the TP 170micro
SIMATIC S5
RS 232
AS 511
TTY
RS 232
SIMATIC 500/505
PLCs from other

manufacturers
SIMATIC S7/M7
RS 485
SIMATIC 500/505
RS 422
PLCs from other
manufacturers
RS 422/RS 485
PROFIBUS DP-Terminal
Figure 4-9
4-8
Connecting a PLC to the TP 170A


TP 170B
OP 170B
SIMATIC S5
RS 232
AS 511
TTY
RS 232
SIMATIC 500/505
PLCs from other

manufacturers
SIMATIC S7/M7
RS 485
SIMATIC 500/505
RS 422
PLCs from other
manufacturers
RS 422/RS 485
PROFIBUS DP-Terminal
Figure 4-10
Connecting a PLC to the TP 170B or OP 170B
The interfaces are described in the Technical Data.
Note when connecting

Notice
Use only the approved cables for connection to a SIMATIC S7 PLC.
In serial operation, only connect the PLC to one of the two interfaces: RS 232 or RS 422/RS
485.
Standard cables are available for the connection. Refer to SIMATIC HMI Catalog ST80.1.

4-9

Configuring the interface

The RS 422/RS 485 interface can be configured by changing the switch settings on the DIL
switch. In this case, the RS 422 received data and the RTS signal are interchanged.
By default, the DIL switch is set for the SIMATIC S7 PLC.
1
2
3
Figure 4-11
Position of the DIL switch on the TP 170A and TP 170B
2
3
Figure 4-12
Position of the DIL switch on the OP 170B
Rear panel cover
Illustration of the switch positions
DIL switch
Note
Note the diagrams of the DIL switch settings on the back of the HMI device. Also refer to the
above diagram.
The following table describes the DIL switch settings according to the type of communication
to be selected. With RS 485, the transmitting and receiving direction is switched internally
with the RTS signal.
4-10


Table 4-1
DIL switch settings on the TP 170A, TP 170B and OP 170B
Communication
Switch setting
4 3 2 1
PPI
MPI/PROFIBUS DP
RS 485
ON
4 3 2 1
ON
PLC
Meaning
RTS on Pin 4
like controller
RTS on Pin 9
like programming device
No RTS on connector
4 3 2 1
ON
PPI
MPI/PROFIBUS DP
RS 485
PLC
4 3 2 1
ON
RS 422
RS 422
RS 422 interface is
enabled
PLC
PLC
Button
State on delivery
4 3 2 1
ON
ON
Compressing the internal program memory of the SIMATIC S5 controller

Notice
In the case of the SIMATIC S5, compressing the PLC's internal program memory
("Compress" PU function, integrated FB COMPR) is not permitted if an HMI device is
connected. When memory is compressed, the absolute addresses of the blocks in the
program memory change. Since the HMI device only reads the address list during startup, it
does not recognize the address change and accesses the wrong memory areas.
If you cannot avoid compressing memory during operation, turn off the HMI device before
running the compress function.
See also
Technical data, TP 170micro, TP 170A and TP 170B (Page 12-2)
Transfer (Page 6-42)
Configuring transfer mode for the TP 170A (Page 6-37)
4-11

4.3.6
Connecting the configuration computer
The following figure depicts the connection between the HMI device and the configuration
computer for transferring the image, project and other project data.
TP 170micro
RS 485
RS 232
Figure 4-13
Connecting the TP 170micro to the configuration computer
To enable RS 485/RS 232 switching, the PC-PPI adapter, Order No.: 6ES7 901-3CB300XA0, can be ordered from Siemens AG.
Set the DIL switch on the PC-PPI adapter as follows:
1
0
1
1 2 3 4 5 6 7 8
Figure 4-14
Setting PC-PPI adapter
DIL switch 5 to 0 for PPI/Freeport
The DIL switches1 to 4 and 5 to 8 are not important when connecting a configuration
computer.
4-12


TP 170A
TP 170B
OP 170B
PC
COM 1
COM 2
RS 232
PG 7xx
COM 2
RS 232
PC
MPI Card
MPI/PROFIBUS DP
PG 7xx
MPI Card
MPI/PROFIBUS DP
Figure 4-15
Connecting the TP 170A, TP 170B and OP 170B to the configuration computer

Data can be transferred via any interface on the HMI device.
Note
Updating the operating system
If no image or no operable image appears on the HMI device, the operating system must be
updated via the RS 232 interface.

4-13

4.3.7
Connecting a TP 170B or OP 170B to peripheral equipment
The following diagram illustrates the connection between the HMI device and a printer.
TP 170B
OP 170B
RS 232
Figure 4-16
Connecting a printer

Notice
Use only cables with a braided metal shield grounded at both ends for connecting the HMI
device and printer.
Some printers may require that the ASCII character set used in the project is also defined on
the printer.
When printing, the HMI device uses the communication protocol XON/OFF. Configure this
report on the printer. When connecting a printer, the following settings are also required:
DIL switch to RS 232, whereby only the RxD, TxD and GND signals are required,
8 data bits
1 Stop bit
No parity
Baud rate between 9600 and 57600, printer-dependent
The Siemens Catalog ST 80 contains the printers approved by Siemens AG. A current list of
approved printers is available on the Internet under Service & Support.
Note
Documentation on the peripheral equipment
When establishing the connection, always refer to the instruction manuals for the peripheral
equipment.
4-14


See also
Printer (Page 6-28)
4.3.8
Connecting the power supply
The following diagram illustrates the connection between the HMI device and power supply.
TP 170micro
TP 170A
TP 170B
OP 170B
Figure 4-17
Power Supply

The plug-in terminal block for connecting the power supply is contained in the accessory kit
and designed is for cables with a cross-section of 1.5 mm2.

4-15

Connecting the terminal block

Notice
Damage
The pressure on the screwdriver can cause the HMI device's socket for the terminal block to
lift from the circuit board when the terminal block is plugged into the device.
Only connect the wires when the terminal block has been unplugged.
2
GND
DC +24 V
Figure 4-18
Connecting the terminal block
Connect the terminal block to the power supply lines as illustrated in the above diagram.
Ensure that the lines are not crossed. Refer to the label for the pin contact on the back of the
HMI device.
Reverse battery protection

The HMI device is equipped with reverse battery protection.

Caution
Ensure safe electrical insulation of the power supply. Use only power supply units that
conform to IEC 364-4-41 or HD 384.04.41 (VDE 0100, Part 410).
Only use power supply units which comply to SELV (Safety Extra Low Voltage) and PELV
(Protective Extra Low Voltage - potential-free low voltage) standards.
The supply voltage must be within the specified range to avoid malfunctions on the HMI
device.
Potential equalization line
If the power supply for the HMI device is not grounded, the IF1 interface could be destroyed
by the potential difference between the HMI device and CPU.
Therefore, connect the 24 V output of the power supply to the potential equalization.
Refer to the Technical Data section for information on the power supply requirements.
4-16


See also
Technical data, TP 170micro, TP 170A and TP 170B (Page 12-2)
Technical data, OP 170B (Page 12-4)
4.3.9
Switch on and test the HMI device
Switching on and testing the TP 170micro and TP 170A

Proceed as follows:
1. Plug the terminal block in the HMI device.
2. Switch on the power supply to the HMI device.
After the power supply is switched on, there is a delay before the display illuminates. The
following screen then briefly appears:
Figure 4-19
Startup screen
If the HMI device does not start, it is possible the wires on the terminal block have been
crossed. Check the connected wires and change the connections, if necessary.
For TP 170micro:
Loader B 7.0.0.xx
Transfer
Transfer
Start
Figure 4-20
Control
Loader on the TP 170micro

4-17

For the TP 170A:
Loader B 7.0.0.xx
Transfer
Transfer
Config
Start
Control
Figure 4-21
Loader on the TP 170A
When no project is available on the HMI device, the device will automatically switch to
transfer mode for the initial startup after the operating system is loaded. The following
dialog appears:
Transfer ...
Connecting to host ...
Cancel
Figure 4-22
Dialog "Transfer ..."
3. Press "Cancel".
Notice
If a project already exists when the HMI device is restarted, the project is started and the
transfer mode is not initiated.
Exit from the project by pressing the corresponding operating element.
After cancellation of the transfer or closing a project, the loader is displayed.
Switching on and testing the TP 170micro and TP 170B

Proceed as follows:
1. Plug the terminal block in the HMI device.
2. Switch on the power supply to the HMI device.
After the power supply is switched on, there is a delay before the display illuminates. The
following screen then briefly appears:
Figure 4-23
4-18
Startup screen


If the HMI device does not start, it is possible the wires on the terminal block have been
crossed. Check the connected wires and change the connections, if necessary.
Figure 4-24
Loader
When no project is available on the HMI device, the device will automatically switch to
transfer mode for the initial startup after the operating system is loaded. The following
dialog appears:
Figure 4-25
3. Press "Cancel".
Notice
If a project already exists when the HMI device is restarted, the project is started and the
transfer mode is not initiated.
Exit from the project by pressing the corresponding operating element.
After cancellation of the transfer or closing a project, the loader is displayed.
Navigation in the loader using the OP 170B

Key
Effect of pressing
or
After pressing one of these buttons, the next function is selected in the
direction of the cursor key.
On pressing and holding the key combination, the next functions are
selected in succession in the direction of the cursor key.

4-19

Function test
Initiate a function test following commissioning. The HMI device is functional when one of the
following conditions occurs:
The "Transfer" dialog is displayed
The loader is displayed
A project is started
Switch off HMI device

Switch off the HMI device in the following ways:
Switch off the power supply
Unplug the terminal strip from the HMI device
4-20

Operator control elements and displays

5.1
Operating elements and indicators on the front of the TP 170micro, TP

170A and TP 170B
Figure 5-1
Operator controls
Display with touchscreen
A touchscreen is the standard input device on the TP 170micro, TP 170A and TP 170B. All
the buttons required to operate the monitored system are displayed on the touchscreen after
starting the HMI device.
Notice
Touchscreen damage
Operating the touchscreen with hard, sharp or pointed items or in a heavy-handed way can
lead to a considerable reduction in its service life and even to complete failure.
Only press the HMI device's touchscreen with your fingers or a touchscreen pen.
See also
Design of the TP 170micro HMI device (Page 1-1)
Design of the TP 170B HMI device (Page 1-3)
Design of the TP 170A HMI device (Page 1-2)

5-1

5.2 Other operator controls on the TP 170A and TP 170B
5.2
Other operator controls on the TP 170A and TP 170B

Operating elements on the side and at the back of the HMI device include:
Memory card slot (TP 170B only)
DIL switches for the RS 422/RS 485 switch
Operation of these elements is described below.
5.2.1
Using the memory card with the TP 170B
Notice
Insert memory card
When inserting a memory card, ensure that it is parallel to the back of the HMI device. The
memory card in the HMI device may be otherwise pushed past the guides and the memory
card will fall inside the housing.
Procedure - using a memory card

Proceed as follows:
1. Insert a memory card in the memory card slot as illustrated in the following diagram.
1
2
3
Figure 5-2
5-2
Plugging the memory card in the TP 170B
Memory card slot
CF card
Arrow


5.2 Other operator controls on the TP 170A and TP 170B
When inserting the memory card, please note that it can only be inserted into the memory
card slot as illustrated in the diagram. The arrow indicates the front side of the memory card
and the direction for inserting it. When the memory card is inserted correctly in the memory
card slot, it protrudes about 3 mm out of the slot.
5.2.2
Unplugging the memory card
Procedure - unplugging a memory card

Notice
Data loss
If the HMI device accesses the data on the memory card while the card is being removed,
the data on the memory card will be destroyed.
Do not remove the memory card when data is being accessed. Note the corresponding
alarms on the display.
Proceed as follows:
1. Grasp memory card
2. Pull the memory card from the memory card slot.
3. Store the memory card in a protective case.
5.2.3
Setting the DIL switch

The DIL switches are already configured for connecting the HMI device to a SIMATIC S7.

5-3

5.3 Front side operating elements and indicators on the OP 170B
5.3
Front side operating elements and indicators on the OP 170B
3
4
Figure 5-3
Operating elements and indicators
Softkeys with LEDs
Softkeys without LEDs
System keys with digit keypad
Cursor keys
The standard input device for the OP 170B is the keyboard. This is basically composed of
two key groups:
Function keys
F1 to F14 and K1 to K10
The softkeys can only be assigned in a configuration. They have no function in the
loader.
System keys
The numeric keypad and control keys are system keys.
5-4


5.4 Other operating elements on the OP 170B
Notice
Keyboard damage
Operating the keys with hard, pointed or sharp objects or in a heavy-handed way can
lead to a considerable reduction of the service life and even to complete failure.
Only use your fingers to operate the HMI device keys.
Note
Unintentional actions can be triggered by a multiple key operation.
No more than two function keys can be activated simultaneously.
See also
Design of the OP 170B HMI device (Page 1-4)
5.4
Other operating elements on the OP 170B

Operating elements on the side and at the back of the HMI device include:
Guides for the labeling strips
Memory card slot
DIL switches for the RS 422/RS 485 switch
Operation of these elements is described below.
See also
Design of the OP 170B HMI device (Page 1-4)
Connecting the PLC (Page 4-8)

5-5

5.4.1
Using the memory card with the OP 170B
Notice
Insert memory card
When inserting a memory card, ensure that it is parallel to the back of the HMI device. The
memory card in the HMI device may be otherwise pushed past the guides and the memory
card will fall inside the housing.
Procedure - using a memory card

Proceed as follows:
1. Insert a memory card in the memory card slot as illustrated in the following diagram.
1
2
3
Figure 5-4
Plugging the memory card in the OP 170B
Memory card slot
CF card
Arrow
When inserting the memory card, please note that it can only be inserted into the memory
card slot as illustrated in the diagram. The arrow indicates the front side of the memory card
and the direction for inserting it. When the memory card is inserted correctly in the memory
card slot, it protrudes about 3 mm out of the slot.
5-6


Procedure - unplugging a memory card

Notice
Data loss
If the HMI device accesses the data on the memory card while the card is being removed,
the data on the memory card will be destroyed.
Do not remove the memory card when data is being accessed. Note the corresponding
alarms on the display.
Proceed as follows:
1. Grasp memory card
2. Pull the memory card from the memory card slot.
3. Store the memory card in a protective case.
5.4.2
Labeling the OP 170B softkeys
Labeling the function keys

Label the function keys based according to the project. Use labeling strips for this.
The labelling strips can be inserted before or after installation of the HMI device.
Printing the labeling strips

The templates for the labeling strips are in the "Slide170.doc" file on the "WinCC flexible"
installation CD in the "\Support\Documents" folder. The file can be edited with MS Word or
Wordpad, for example.
Pay attention to the information provided in the file.

5-7

3
3,1
8,5
3,6
0
3,1
8,6
3
14,5
21,08
26,58
6
39,06
44,56
14,5
57,04
62,54
73,5
8,5
3,1
94,5
99,6
105,1
119,1
124,6
22,6
28,1
135,5
39
159
62,5
17
Figure 5-5
17
Labeling strip dimensions
Printable foil or paper can be used for labeling strips. Use of transparent foil ensures the
LEDs on the softkeys remain visible. Permissible thickness of the labeling strip: 0.15 mm.
Proceed as follows
Proceed as follows:
1. Edit and print templates
Another option is to print blank templates and label them afterwards.
Notice
Do not write on the keyboard to label the softkeys.
2. Cut out labeling strips

Ensure that the corners are cut according to the above diagram. It simplifies sliding them
in the guide.
5-8


3. Remove the existing labeling strips
Note
Wait for the ink to dry before inserting strips wait until the inscription is dry.
4. Slide the labeling strips in the guide
1
2
3
Figure 5-6
Insert the labeling strips.
Guide
Inserted labeling strips
Inserting labeling strips
5. Slide the labeling strips to the end of the guide.

The labeling strip will protrude approximately 1 cm out of the guide. The template is sized so
that the labeling is correctly placed behind the softkey fields. A stop for the labeling strips is
not necessary.
See also
Connecting the PLC (Page 4-8)
5.4.3
Setting the DIL switch

The DIL switches are already configured for connecting the HMI device to a SIMATIC S7.

5-9

5-10

Operating system and configuration

6.1
Configuring the TP 170micro and TP 170A operating system

The HMI device is ready to operate upon delivery. The Microsoft Windows CE operating
system is installed.
After switching on the HMI device, the loader appears during the start phase for approx. 3
seconds. If a project is already loaded on the HMI device, it is started. The HMI device
otherwise switches to transfer mode.

Loader B 7.0.0.xx
Transfer
Transfer
Start
Figure 6-1
Control
The buttons in the loader trigger the following functions:

"Transfer"
This button switches the HMI device to the transfer mode to enable data transfer.
"Start"
This button starts a project stored on the HMI device.
"Control"
This button opens a configuration menu for the HMI device.
Before a project is transferred and started, configure the HMI device according to the specific
conditions of use. Press the "Control" button to open the "Control Settings" dialog.

6-1

6.1 Configuring the TP 170micro and TP 170A operating system

Loader B 7.0.0.xx
Transfer
Transfer
Config
Start
Control
Figure 6-2

"Transfer"
"Config"
This button opens a configuration menu for data channels of the HMI device.
"Start"
"Control"
This button opens a configuration menu for the HMI device.
conditions of use. Press the "Control" button to open the "Control Settings" dialog.
See also
Switch on and test the HMI device (Page 4-17)
6.1.1
Operating by touch
Operations are carried out exclusively by touching the touchscreen. The pressure-sensitive
mask on the screen detects contact. The position of the point of contact is assigned to a
control object behind it. This enables a control object or a programmed function is triggered.
See also
Touchscreen calibration (Page 6-35)
6-2


6.1.2
"Control Settings" dialog
General procedure - changing settings

Notice
Changing system settings
Changes which affect the transfer only take effect after shutting down and restarting the
operating system.
Proceed as follows:
1. Close the project.
2. Open the "Control Settings" dialog.
3. Change the settings for the respective function.
4. Close the "Control Settings" dialog.
5. Switch off HMI device
6. Switching on the HMI device.
Requirement
The HMI device is switched on.
"Control" was pressed in the loader.
The following dialog appears:
Control Settings
Contrast +
Contrast
1
2
Calibrate
ScreenSaver Settings
Idle Time = 360 min
Down
Up
Language Settings
English
German
OK
Figure 6-3
"Control Settings" dialog
Buttons for contrast control
Buttons for calibration
Buttons for the screensaver
Language selection checkboxes

6-3

The following can be set in the "Control Settings" dialog:
Display contrast
Calibration of the touchscreen
Duration of screensaver display
Operating system language
Note
The entry which is currently active is always displayed in a dialog.
Procedure setting the contrast

The dialog is used to adjust the contrast and thus indirectly controls the brightness of the
HMI device display.
Notice
Screen contrast
The screen contrast can be increased and decreased within a wide range. Note that this can
lead to the screen content becoming unrecognizable in certain lighting conditions.
The "Contrast +" button increases the contrast. The "Contrast " button reduces the contrast.
The procedure is described in the section "Touchscreen calibration".
Procedure setting the screensaver

To set the delay period for of the screensaver, proceed as follows:
1. Press "Up" to increase the value displayed in "IdleTime".
2. Press "Down" to decrease the value displayed in "IdleTime".
The values can be changed in intervals of 5 minutes.
Valid value range: 0 min to 360 min.
The default setting is "0". The screensaver remains deactivated for the period defined by this
value.
6-4


6.2 Configuring the operating system for TP 170B and OP 170B
Procedure setting the operating system language

The operating system supports German and English.
Setting the language controls the format used to display the date, time and corresponding
separators for the selected country. The decimal separator is either a period or a comma
according to the selected language.
Note
If a language used in the project is not supported by the operating system on the HMI
device, the national formats specified by the activated "Language Settings" checkbox are
used.
6.2
Configuring the operating system for TP 170B and OP 170B
The loader for the TP 170B and OP 170B

The HMI device is ready to operate upon delivery. The Microsoft Windows CE operating
system is installed.
After switching on the HMI device, the loader appears during the start phase for approx. 3
seconds. If a project is already loaded on the HMI device, it is started. The HMI device
otherwise switches to transfer mode.
Figure 6-4
Loader, TP 170B and OP 170B

"Transfer"
"Start"
"Control Panel"
The button opens configuration submenus for the HMI device.
conditions of use. Open the Control Panel to do this.

6-5

Navigation in the loader using the OP 170B

Key
TAB
SHIFT
Effect of pressing
Pressing one of these keys selects the next menu command. If pressed
or
and held, the menu runs continuously.
TAB
or
ENTER
Pressing this key selects the previous menu command. If pressed and
held, the menu runs continuously.
The function assigned to the activated button is executed.
See also
Switch on and test the HMI device (Page 4-17)
6.2.1
Operating by touch
Operations are carried out exclusively by touching the touchscreen. The pressure-sensitive
mask on the screen detects contact. The position of the point of contact is assigned to a
control object behind it. This enables a control object or a programmed function is triggered.
See also
6.2.2
Navigating and operating
Introduction
The functions are available in the Control Panel as icons. Clicking on the icon opens the
corresponding dialog. This allows you to adapt the HMI device to the system environment.
Requirement
The HMI device is switched on.
The loader is displayed
6-6


Note
Cancel transfer
The "Transfer ..." mode can be cancelled by pressing "Cancel" on the TP 170B and
<ESC> on the OP 170B.
6.2.2.1
Operating and navigating in Control Panel
Procedure open the Control Panel

Proceed as follows to open the Control Panel:
1. Press the "Control Panel" button in the loader.
2. if a project is running, press the control object which is linked to the function for opening
the loader.
This procedure can only be performed when a corresponding function has been
configured in the project.
The following window opens:
Figure 6-5
Control Panel
Fifteen functions are integrated in the Control Panel. They are described below. The
functions "S7 Transfer" and "Transfer" are described in the section "Configuring data
channels".
Note
The
button has no function.

6-7

Navigation in the Control Panel menu using the OP 170B

The arrangement of the icons in the Control Panel can be changed to faceplate navigation.
For the TP 170B: Click on "View."
For the OP 170B: Open the "View" menu with
ALT
A menu with four commands opens:

Large Icons
The icons are displayed as depicted in the above diagram.
Small Icons
The icons are displayed smaller.
Detail
Smaller icons are displayed and descriptions are also provided.
Arrange Icons
The icons can be sorted according to name and description.
The following keys can be used to navigate within the Control Panel of the OP 170B:
Table 6-1
Keys for navigating in the Control Panel at the OP 170B
Key
Effect of pressing
or
or
After pressing one of these buttons, the next icon is selected in the
If pressed and held, the next icons are selected in succession in the
or
SHIFT
or
On pressing one of these key combinations, several icons are selected.

If pressed and held, the next icons are selected in succession in the
SHIFT
or
SHIFT
or
SHIFT
The list arrow has no function and therefore cannot be selected.
6-8


Procedure closing the Control Panel on the TP 170B

Proceed as follows to close the Control Panel:
1. Press
The Control Panel is closed. The loader is displayed again.

The Control Panel can also be closed via the "File" menu.
1. Click on "File".
The following menu opens:
Figure 6-6
"File" menu
2. Press "Close".
Procedure closing the Control Panel on the OP 170B

Proceed as follows to close the Control Panel:
1. Press
ALT
The following menu opens:
Figure 6-7
"File" menu
2. Select "Close" with
or
The selected menu option is displayed in reversed colors.

3. Press
ENTER
The Control Panel is closed. The loader is displayed again.

6-9

6.2.2.2
Operating and navigating in a dialog
Requirement
An icon is selected in the Control Panel.
Procedure - opening a function dialog

Applies to the TP 170B:
1. Double-click on the icon.
The icon becomes darker and the name of the icon is displayed in reversed colors. The
associated function then opens.
Applies to the OP 170B:
There are two methods of opening a function:
Using system keys
Using the menu bar:
Opening function using system keys
1. Select the icon in the Control Panel.
The icon becomes darker and the name of the icon is displayed in reversed colors.
2. Press
ENTER
The function is opened.

Opening function using the menu bar
1. Select the icon in the Control Panel.
2. Open the menu bar by pressing
ALT
3. Select "Open".
4. Press
ENTER
The function is opened.
6-10


Navigation in a "Control Panel" dialog using the OP 170B.

Table 6-2
Keys for the navigation in a dialog of the "Control Panel" using the OP 170B
Key
Effect of pressing
On pressing this key, the next field is activated according to the
TAB
configured tab order setting.

On pressing and holding the key, the fields are activated in succession
based on the tab order setting.
SHIFT
On pressing this key combination, the next field is activated in the order
TAB
of the tab setting.

On pressing and holding the key, the fields are activated in succession
based on the configured tab order.
SHIFT
SHIFT
or
On pressing one of these key combinations, several functions are

selected.
SHIFT
SHIFT
+
+
or
On pressing one of these key combinations, several functions are

selected.
ESC
ENTER
On pressing <ESC>:
The dialog is closed.
The original values remain valid as long as <ENTER> is not pressed.
On pressing <ENTER>:
The dialog is closed when no the button is activated.
The entered values are valid.
Information is available in the following sections on the content and setting options in the
dialogs. The procedure is described using examples of dialogs from OP 170B. The examples
also apply to the TP 170B.

6-11

Procedure - closing a function dialog

Applies to the TP 170B:
1. Press
in order to discard the entries.
The activation has the same effect as <ESC>.

2. Press
in order to accept the entries
The activation has the same effect as <ENTER>.

Applies to the OP 170B:
1. Press
ESC
The dialog is closed.

If open dialogs cannot be closed, proceed as follows:
1. Open another dialog in the Control Panel.
2. Use
ALT
TAB
to move to another open dialog.
3. Close the dialog with
ESC
or
ENTER
Repeat steps 2 and 3 as necessary until all the dialogs are closed.
General procedure - changing settings

Notice
Changing system settings
Changes which affect the transfer only take effect after shutting down and restarting the
operating system.
Proceed as follows:
1. Close the project.
2. Opening Control Panel
3. Change the settings for the respective function.
4. Close the Control Panel.
5. Switch off HMI device
6-12


6.2.3
Backup/Restore
Requirement
was activated in Control Panel.
For backup:
A memory card with 16 MB is inserted in HMI device.
For restoring:
A memory card containing the image to be transferred is inserted in the HMI device.
"Backup/Restore" dialog
Figure 6-8
Button for data backup
Button for data restore
The "Backup/Restore" dialog contains the "BACKUP" and "RESTORE" buttons. These
buttons are used to transfer project data between the HMI device and the memory card.
Note
After selecting "Backup" or "Restore" and confirming with <ENTER>, the selected action is
immediately executed on the HMI device.
If no memory card is inserted in the memory card slot, an alarm appears. Insert the memory
card and confirm with <ENTER>. If a memory card card is not inserted, the Control Panel
reappears after acknowledging an alarm.
See also
Backup and restore project (Page 7-13)

6-13

6.2.4
Communications Properties
Requirement
was activated in the Control Panel.
"Communications Properties" dialog
1
2
3
Figure 6-9
"Communications Properties" dialog, "Device Name" tab register
The HMI device uses this information to identify itself to other computers.
Name of the HMI device
Description for the HMI device
Network communication has not been approved for TP 170B and OP 170B. Do not change
the settings in this dialog.
6-14


6.2.5
Date/Time
Requirement
"Date/Time Properties" dialog
1
2
3
4
5
Figure 6-10
"Date/Time Properties" dialog
Time zone selection box
Time selection box
Date selection box
"Summertime" checkbox
Button
The "Date/Time Properties" dialog contains the "Date/time" tab.

The "Date/time" tab can be used to:
Set the time zone
Select the date
Correct the set time
Activate the "Daylight savings time ..." checkbox for switching to summertime
The default settings are:
"Pacific Time (US & Canada)" for the USA and Canada time zone
"Not enabled" "Daylight savings time ..." checkbox switching to summertime is not
activated.

6-15

Proceed as follows
Proceed as follows:
1. Select the time zone.
2. Press "Apply".
The selected time zone goes into effect when this buttong is pressed.
3. Correcting date and time
If you activated "Daylight savings ..." and the set date falls within the summertime period,
then an hour is added automatically to the set time.
For the TP 170B:
You can also press
instead of "Apply". The entries are applied and the dialog closed.
For the OP 170B:

You can also press <ENTER> instead of "Apply." The changes are applied.
Synchronizing date and time with the PLC

The date and time of the HMI device can be synchronized with the PLC, if this has been
configured in the project and the PLC program..
Further information on this subject is available in the "WinCC flexible" system manual.
Notice
Synchronize the date and time when time-controlled responses should be triggered in the
PLC by the HMI device.
6.2.6
InputPanel
The "Input Panel" function is used to input alphnumeric and numeric characters in the
Control Panel on the TP 170B.
This keyboard cannot be used in a project.
Requirement
6-16


"Siemens HMI Input Panel Options" dialog
1
2
3
Figure 6-11
"Siemens HMI Input Panel Options" dialog
Button for opening the screen keyboard
Button for saving size and position of the screen keyboard
Button for closing the screen keyboard
The "Siemens HMI Input Panel Options" dialog is used to:

Open the screen keyboard
Enlarge the screen keyboard
Fix the keyboard position on the screen
The screen keyboard is provided for input in Control Panel dialogs.
Proceed as follows to open the screen keyboard, save its position on the screen and close
the "Siemens HMI Input Panel Options" dialog:
Procedure - opening the screen keyboard

1. Press "Start Resize".
The screen keyboard is opened and appears as follows.
Figure 6-12
The screen keyboard is in alphanumeric mode.

6-17

Procedure - moving the screen keyboard and saving position

1. Touch
The screen keyboard can be moved on the screen. Release the icon when the required
position is reached.
2. Press "Save".
Note
To save the new size and position of the keyboard, switch on the alphanumeric keyboard
before saving it.
The size and position of the screen keyboard on the screen are saved. The next time it is
opened, the screen keyboard appears in the same size and position.
The following keys change the display format of the screen keyboard:
Upper case letters appear on the screen keyboard instead of lower case. This format is
useful when upper case are primarily being entered.
Only the numeric keys appear on the screen keyboard. The display is useful for entering
numbers.
Figure 6-13
The screen keyboard as numeric keypad
Clicking on "Num" again expands the screen keyboard.
6-18


The numeric and alphanumeric keys are hidden on the screen keyboard. The display is
useful for input using the cursor keys.
Figure 6-14
Screen keyboard for input using the cursor keys
Clicking on "Ctrl" returns the screen keyboard to full display.
All the keys in the screen keyboard are hidden. This format is useful when the open
screen keyboard is still needed for further input but a dialog is covered by the screen
keyboard.
Figure 6-15
Minimized screen keyboard
Note
This display format is also useful when you want to close the dialog "Siemens HMI Input
Panel Options" using the button "Close Input Panel."
Procedure - closing the "Siemens HMI Input Panel Options" dialog

1. Press
in the "Siemens HMI Input Panel Options" dialog.
The "Siemens HMI Input Panel Options" dialog is closed. The screen keyboard remains
open.

6-19

Procedure - closing the screen keyboard

For the TP 170B:
1. Double-click on
or press "Close Input Panel".
The screen keyboard is closed. The "Siemens HMI Input Panel Options" dialog remains
open.
For the OP 170B:
1. Press
TAB
2. Press
ENTER
to select "Close Input Panel".

.
The "Siemens HMI Input Panel Options" dialog is closed. The Control Panel is
displayed again.
6.2.7
Keyboard
Requirement
"Keyboard Properties" dialog
1
2
3
4
5
Figure 6-16
"Keyboard Properties" dialog
Repeat character checkboxes
Delay until character is repeated
Rate for repeat character
Slider control
Test field
The "Keyboard Properties" dialog contains the "Repeat" tab.
6-20


The "Repeat" tab is used to
Enable repetition of characters
Set delay time until character repetition
Set the rate for character repetition and
Test the set values.
The default setting for enabling the character repetition is "Enabled". When a key is pressed
for a long time, the characters are repeated until the respective button is released.
Note
Changing settings
The settings in the "Keyboard Properties" dialog can be changed either by using the cursor
keys in the dialog or by moving the slider.
Proceed as follows
Proceed as follows to test set values:
1. Select the test field.
For the TP 170B:
The screen keyboard is opened. Move the screen keyboard as needed.
2. Press any character and hold it down.
Check the implementation of the character repetition and the rate of the character
repetition in the test field.
3. Correct the settings if necessary.
6.2.8
Mouse
Requirement
Note
Mouse connection
A mouse connection for the HMI devices TP 170B and OP 170B has not been approved.
The operation of the touchscreen on the TP 170B can be set in the dialog.

6-21

"Mouse Properties" dialog
1
2
3
4
5
Figure 6-17
"Mouse Properties" dialog
Touch the input field 2 two times in succession to set the speed and time between contacts
on the touchscreen.
Input box
No function
Control field
Touch the control field 4 two times in succession to control the entries. If the control field does
not change, change the entry again.
The "Mouse Properties" dialog contains the "Double Click" tab.

The "Double Click" tab is used to:
Set the double-click speed.
The time span between two contacts on the entry field is measured.
Test the double click speed
The time span between two contacts on the control field is measured.
Proceed as follows
To enter the speed and time span between two contacts on the touchscreen, proceed as
follows:
1. Touch the entry field two times in quick succession.
On the second contact, the entry field is displayed in reverse colors, as can be seen in
the following figure:
2. Touch the control field two times in quick succession as you did on the entry field.
When the control field is touched in this way, it is displayed after the second contact as
follows:
If the control field remains unchanged, repeat the setting of the entry field.
6-22


Result
The doubleclick on the touchscreen is now set.
6.2.9
OP
Requirement
"OP Properties" dialog
1
2
3
4
Figure 6-18
"OP Properties" dialog, "Persistent Storage" tab
The current tab entries are saved. When the HMI device is restarted, the tab entries are also
started automatically.
Button for saving tab entries
Button for saving temporary files
Saves all the files currently in the temporary directories in the Flash memory. These files are
written back when the HMI device is started. Files in the \temp directory are not saved.
The "OP Properties" dialog contains the "Persistent Storage", "Display", "Device" and
"Touch" tabs.
The "Persistent Storage" dialog saves the current tab entries and temporary files.
The "Display" tab defines the screen settings.
The "Device" tab displays information about the HMI device.
The "Touch" tab calibrates the touchscreen.

6-23

Procedure saving tab entries and files

The "Persistent Storage" tab contains the "Save Registry" and "Save Files" buttons.
"Save Registry"
On pressing "Save Registry," the current tab entries are saved in the internal Flash
memory. The HMI device uses these saved tab entries the next time it starts.
"Save Files"
On pressing "Save Files," temporary files are saved in the internal Flash memory. These
files are written back during the startup routine. Files in the "Temp" directory are not
saved.
Procedure setting the display
Figure 6-19
"OP Properties" dialog, "Display" tab
Button for increasing the contrast
Button for decreasing the contrast
The "Display" tab contains the "Contrast" group with the "UP" and "DOWN" buttons. Proceed
as follows to change the screen contrast:
1. Press "UP".
The contrast is increased and the screen becomes darker.
2. Press "DOWN".
The contrast is reduced and the screen becomes lighter.
6-24


Procedure displaying HMI device features
1
2
3
4
5
Figure 6-20
"OP Properties" dialog, "Device" tab
HMI device name
Version of the image
Version of the boot loader
Boot loader release date
Size of the internal Flash memory
The "Device" tab is used to display HMI device data. There are no input options. The
following is displayed in this tab:
HMI device name
Version of the boot loader
Boot loader release date
Capacity of the internal Flash memory. This is the memory for saving the image and
project with associated recipes.
Note
The version of the image can also be found by starting the loader. The version
information is shown in the title line.
You will need this information when contacting A&D Technical Support.

6-25

Procedure calibrating the touchscreen
2
Figure 6-21
"OP Properties" dialog, "Touch" tab
If the HMI device does not react precisely, the touchscreen may need to be calibrated.
Buttons for calibrating the touchscreen
See also
6.2.10
Password
Requirement
"Password Properties" dialog
1
2
"Password Properties" dialog

1
Password input field
Input field for entering the password a second time
The "Password Properties" dialog contains the "Password Settings" tab.

The "Password Settings" tab protects the functions in the Control Panel.
6-26


Procedure entering a password

Proceed as follows:
1. Enter a password in the "Password" field.
Notice
Style
Spaces and the special characters * ? are in this entry field. . % / \ ' " are not permitted in
this field.
2. Repeat the password in the "Confirm Password" field.

Note
Coding
Each character entered in the fields is represented by an
Result
If a password has been assigned, access to the Control Panel in the loader is only permitted
after entering the password. The "Enter Password" dialog opens on pressing the "Control
Panel" button.
Note
If the required password is no longer known, the Windows CE image must be reinstalled.
The Control Panel can then be accessed again without restriction.
Procedure deleting a password

Proceed as follows:
1. Open the loader.
2. Press "Control Panel".
3. Enter the password.
4. Select the "Password" function.
5. Enter the password.
The "Password Properties" dialog opens.
6. Delete the entry in "Password:" and "Confirm Password:" deleting
7. Confirm with <ENTER>.
Close the "Password Properties" dialog.
Result
The password protection is canceled.
6-27

6.2.11
Printer
Requirement
"Printer Properties" dialog
1
2
3
4
5
6
Figure 6-22
"Printer Properties" dialog
Printer language selection box
Selection box for the interface to the connected printer
Data network - not approved
Paper size selection box
Option button to define the paper size
Checkboxes for draft and color printing
Use this dialog to select the printer language for the connected printer and to set up the
interface. Settings, such as color or quality of graphic printing, have no effect on the alarm
logging.
Printer language
The following printer languages can be set:
Epson9
PCL Inkjet
PCL Laser
Stylus Color
6-28


In the following selection lists, the available settings depend on the configured printer
language.
Interface
IF 2 with Baudrates 9600, 19200, 38400 and 57600
Data network
Data network
The data network for the HMI devices TP 170B and OP 170B has not been approved.
Paper size
DIN A4
DIN B5
Legal
Letter
Option buttons for the page orientation of the printout:
"Portrait"
"Landscape"
The following settings can be made with the checkboxes:
"Draft Mode"
"Color" for color prints
The following must be set for the printout of hard copies:
Printer language
Interface
See also
Connecting a TP 170B or OP 170B to peripheral equipment (Page 4-14)

6-29

6.2.12
Regional Settings
Requirement
"Regional Settings Properties" dialog
2
Figure 6-23
"Regional Settings Properties" dialog, "Regional" tab
Alteration of regionally dependent settings affects the display and the sequence of numbers
for date, time and values.
Region selection box
The "Regional Settings Properties" dialog contains the "Regional", "Number", "Time" and
"Date" tabs. These tabs are used to
Adapt display to regional standards
Set display format for numerical values
Set display format of time information
Set display format of the date
The default settings are:
"German (Standard)" for the region
The comma as decimal symbol for numbers
"hh:mm:ss" for the time display
"dd.mm.yy" for the abbreviated date format
Procedure setting the region

Select the region where the HMI device is used from the Region selection box.
6-30


Procedure setting the number format and decimal separator
1
2
3
Figure 6-24
"Regional Settings Properties" dialog, "Number" tab
Selection box to select the character for defining decimal places
Selection box to select the number grouping character
Selection box to select the separator character for number sequences
Notice
Displaying a numeric value
A numeric format that differs from the local region can cause the misinterpretation of
displayed numeric values.
Set the display in the tab "Number" according to the region where the HMI device is used.
These selection boxes are used to:

Define the character to separate decimal places
Define a character to separate groups of numbers
Define a character to separate number sequences in lists

6-31

Procedure setting the time format
1
2
3
4
Figure 6-25
"Regional Settings Properties" dialog, "Time" tab
Selection box for defining the time format
Selection box for selecting the separator between hours, minutes and seconds
Selection box for selecting the character indicating the time before noon
Selection box for selecting the character indicating the time after noon

Select the character for the time format
Define the separator between hours, minutes and seconds
Define the characters for indicating morning or afternoon
Procedure setting the date format
1
2
3
Figure 6-26
"Regional Settings Properties" dialog, "Date" tab
Selection box for defining the separator in the date
Selection box for sorting day, month and year
Selection box for the date in long format

Define the separator in the date
Define the order in the date
Set the date to long format
6-32


6.2.13
Screen Saver
Requirement
"Screensaver" dialog
1
2
3
Figure 6-27
"Screensaver" dialog
Activation time for the screensaver
Option buttons for displaying the screensaver
If the value 0 is set, no screensaver is started.
This dialog is used to define the delay period for activating the screensaver. The screen
saver is automatically activated if the HMI device is not operated within the specified period
of time.
Valid value range for TP 170B and OP 170B:
5 to 71582 min
Input can be made using the numeric keypad and the cursor keys. All whole numbers can
be entered in this range.
On entering the value 0, the screensaver is deactivated permanently.
The screensaver display can be toggled between "Standard" and "Blank Screen" using the
option button. If the screensaver is active and the "Standard" option selected, a square
moves diagonally across the screen. In the case of "Blank Screen", nothing appears in the
display.
For touch operation:
The screensaver is deactivated when the screen is touched.
Note
If an operating element is touched when deactivating the screensaver, the function is not
triggered.
For keyboard operation:

The screensaver is deactivated by pressing any key. The function assigned to that key is not
triggered.
6-33

6.2.14
System
Requirement
"System Properties" dialog
Figure 6-28
"System Properties" dialog, "General" tab
Copyright to Microsoft Windows CE
Information about the processor, amount of the internal Flash memory, and capacity of an
inserted memory card
The "System Properties" dialog contains the "General" and "Memory" tabs. These tabs are
used to
Display general information about the HMI device
Define the amount of space for file storage.
The "General" tab contains information on the processor type and memory capacity. In
addition, information appears as to whether a memory card is inserted and its type.
6-34


6.3 Touchscreen calibration
1
2
3
Figure 6-29
"System Properties" dialog, "Memory" tab
The position of the indicator must not be changed
Buffer with information about the total and used capacity
Program memory with information about the total and used capacity
Notice
"Memory" tab
The memory capacity in the "Memory" tab must not be changed.
6.3
Introduction
It may be necessary to recalibrate the screen if operator controls no longer responds.
Environmental influences and natural aging may make a recalibration of the touchscreen
necessary.
Requirement
"Control" was activated in the loader on the TP 170micro and TP 170A.
was activated in the Control Panel on the TP 170B and OP170B.

6-35

6.3 Touchscreen calibration
Procedure calibrating the touchscreen

You can calibrate the touchscreen by pressing the "Calibrate" button in the "Control Settings"
dialog on the TP 170micro and TP 170A. Press "Recalibrate" in the "Touch" tab of the "OP
Properties" dialog to calibrate the touchscreen on the TP 170B and OP 170B. The following
dialog appears for this. Follow the instructions.
Carefully press and breifly hold stylus on the center of
the target. Repeat as the target moves around the screen.
Figure 6-30
"Calibrate touchscreen" dialog
Press carefully and hold the touch pen briefly on the center of the calibration crosshairs.
Repeat the process as long as the calibration crosshairs move on the touchscreen.
Calibration crosshairs
Note
"Calibrate touchscreen" dialog
The opened "Calibrate touchscreen" dialog can only be exited by completing the following
steps.
Proceed as follows:
1. Touch the center of the crosshairs with your finger or touch pen.
Touch the calibration crosshairs for approximately 2 seconds. The calibration crosshairs
will then assume the next position.
If you do not hit the center of the calibration crosshairs, the crosshairs nevertheless
change their position. Repeat the process from the beginning starting with the first
calibration crosshair.
Note
As long as the "Calibrate touchscreen" dialog is open, the screen saver will not be
activated.
6-36


6.4 Configuring transfer mode for the TP 170A
2. Repeat step 1 four times.
The following dialog appears when calibration is completed:
New calibration settings have been measured.
Tape the screen to register saved data.
Wait for 30 seconds to cancel saved data and
keep the current setting.
Time limit: 30 sec
Figure 6-31
"Confirm Calibration" dialog
The new calibration values are measured. Touch the touchscreen to save the calibration
values. The new calibration values will be discarded if you do not touch the touchscreen
within 30 seconds of calibration.
Time remaining until the calibration values are discarded.
3. Save calibration
To save the calibration, press the touchscreen within 30 seconds. Otherwise, the calibration
is discarded and the old settings remain valid.
6.4
Configuring transfer mode for the TP 170A
"Transfer Settings" dialog

The HMI device data channels must be configured to enable data exchange with the PLC or
with the configuration computer.
Select "Transfer > Transfer Settings" in the loader. The following dialog appears:
Transfer Settings
Serial Transfer
Enable
Remote
MPI/DP Transfer
Enable
Remote
Address
Up
Down
Baudrate
187.5 kB
Up
Down
OK
Figure 6-32

6-37

1
Group for the serial transfer settings
Group for the MPI/PROFIBUS DP transfer settings
Buttons for changing the address
Buttons for changing the baud rate
Note
Note the default settings in the "Transfer Settings" menu. The MPI/PROFIBUS DP transfer is
not activated.
Set serial transfer

The "Serial Transfer" group is used to configure the serial interface for the transfer. The
following setting can be made:
"Enable" checkbox
Serial transfer is enabled if this checkbox is activated.
Serial transfer is disabled if this checkbox is deactivated.
Set MPI/PROFIBUS DP transfer

The "MPI/DP Transfer" group is used to configure the MPI/PROFIBUS DP interface for the
transfer. The following setting can be made:
"Enable" checkbox
The MPI/PROFIBUS DP transfer is enabled if this checkbox is activated.
The MPI/PROFIBUS DP transfer is disabled if this checkbox is deactivated.
Setting remote control

During transfer, remote control is used to automatically close a project running on an HMI
device.
The following settings are possible:
"Remote" checkbox
Automatic data transfer is enabled if this checkbox is activated.
In this operating mode, a project is automatically closed when a project transfer is
triggered on the configuration computer.
Automatic data transfer is inhibited if this checkbox is deactivated.
In this operating mode, a project is not automatically closed when a project transfer is
A transferred project is started automatically after the transfer.
The default settings for "Remote" are:
Serial transfer "enabled"
MPI/PROFIBUS DP transfer "disabled"
6-38


Set MPI/PROFIBUS DP address

Use the "Address" input field to enter the value for the MPI/PROFIBUS DP address for the
HMI device. A value in the range from 0 to 126 is permissible. This value range can be
restricted by a project which has already been transferred. Values outside of the range are
rejected, an error message appears and new values can be reentered.
Note
MPI/PROFIBUS DP address
During data transfer via MPI/PROFIBUS DP, note the addresses of the subscribers in the
network. If a project is already loaded on the HMI device, the MPI/PROFIBUS DP address of
the project is used.
The entry can be made using "Up" and "Down".

The default setting is "1".
Set Baudrate
Use the "Baud rate" input field to enter the baud rate value for the MPI/PROFIBUS DP
transfer. The following settings can be made using "Up" and "Down":
19.2 KB
187,5 KB
1.5 MB
3 MB
6 MB
12 MB
If the HMI device subscriber is in an MPI/PROFIBUS DP network, the value to be entered is
determined by the configuration of the MPI/PROFIBUS DP network. Select the
corresponding value.
The default setting is "187.5 KB".
Notice
Address in MPI/PROFIBUS DP network
The value assigned in the "Address" input field may only be used once in a MPI/PROFIBUS
DP network.

6-39

6.5 Configuring transfer mode for the TP 170B and OP 170B
6.5
Configuring transfer mode for the TP 170B and OP 170B
6.5.1
S7-Transfer Settings
"S7-Transfer Settings" dialog
Figure 6-33
"S7-Transfer Settings" dialog
The "S7-Transfer Settings" dialog is use to set the following:

Parameters for the HMI device
Parameters for the MPI/PROFIBUS DP transfer
Bus parameters
The available network connections are listed in the dialog.
Proceed as follows
After selecting one of the network connections listed, the associated parameters can be set.
To view the parameters currently set, press "Properties." One of the following dialogs
appears according to the network connection selected:
1
2
3
4
5
Figure 6-34
6-40
"MPI" dialog
The HMI device is the only master on the bus.
Bus address
Time out
Data transmission rate
Maximum number of subscribers


Activate the "Panel is the only ..." checkbox if no other device is defined as a master in the
MPI/PROFIBUS DP network. Deactivate the checkbox if another device, e.g. a SIMATIC S7400 PLC, is defined as master.
The default settings are displayed in the "MPI" dialog.
1
2
3
4
5
6
7
Figure 6-35
"PROFIBUS" dialog
The HMI device is the only master on the bus.
Bus address
Time out
Data transmission rate
Maximum number of subscribers
Bus profile
Button for opening the "Profile" dialog
Notice
Address in MPI/PROFIBUS DP network
The value assigned in the "Address" input field may only be used once in a MPI/PROFIBUS
DP network.
To view the bus parameters currently set, press "Bus parameters." The following dialog
opens:
Figure 6-36
"Profile" dialog
The contents of the dialog cannot be changed. The values set for the transfer are displayed.

6-41

6.5.2
Transfer
2
3
Figure 6-37
"Transfer Settings" dialog, "Channel" tab
Group for the data channel 1
Group for the data channel 2
Button for the "S7 Transfer Settings" dialog. See section

"S7 Transfer Settings".
The "Transfer Settings" dialog contains the "Channel" and "Directories" tabs.
The "Channel" tab is used to configure data channels 1 and 2.
Set serial transfer

The "Channel 1" group is used to configure the serial interface for the transfer. The following
settings are possible:
"Enable Channel" checkbox
Serial transfer is enabled if this checkbox is activated.
Serial transfer is disabled if this checkbox is deactivated.
Notice
Deactivate the "Enable Channel" checkbox in the "Transfer Settings" dialog if a serial
printer is connected to the IF2 interface of the HMI device.
Set MPI/PROFIBUS DP transfer

The "Channel 2" group is used to configure the interface MPI/PROFIBUS DP and Ethernet
for the transfer. The following settings are possible:
"Enable Channel" checkbox for MPI/PROFIBUS DP transfer and for Ethernet transfer
The channel is enabled if this checkbox is activated.
The channel is disabled if this checkbox is deactivated.
6-42


Setting Ethernet transfer

Ethernet transfer for the HMI devices TP 170B and OP 170B has not been approved.
Setting remote control

"Remote Control" checkbox
Automatic data transfer is enabled if this checkbox is activated.
In this operating mode, a project is automatically closed when a project transfer is
Automatic data transfer is inhibited if this checkbox is deactivated.
In this operating mode, a project is not automatically closed when the project transfer
is triggered on the configuration computer.
A transferred project is started automatically after the transfer.
The default setting for "Enable Channel" and "Remote Control" is "deactivated".
Press the "Advanced" to access the "S7 Transfer Settings" dialog described in the section
"S7 Transfer Settings". Settings can be made in the "S7-Transfer Settings" dialog regardless
of whether data channels 1 and 2 are enabled.
Notice
Settings in "Project File" and "Path"
Do not change the settings in the "Project File" and "Path" fields when working with a
project. The project may not open at the next start of the HMI if changes are made here.
1
2
3
4
Figure 6-38
"Transfer Settings" dialog, "Directories" tab
Storage directory for the project file
Storage directory for the backup of the project file
Autostart directory for the runtime software
Delay period before the project starts
The "Directories" tab can be used to modify the preassigned storage location for a project
file.

6-43

"Project File"
Set the storage location for a project file here. The internal Flash memory and external
memory card are available as storage locations. During the next transfer process, the
project file is stored in the storage location specified.
"Project Backup"
The predefined storage location for your project's source file can be changed here. The
external memory card or the network connection can be defined as the storage location.
During the next backup process, the project's source file is stored in the storage location
specified.
"Autostart application"
Use "Path" to define the storage location in the HMI device for the runtime software.
Use "Wait" to define how long the Start menu should be displayed or whether it should be
displayed continuously before the project is started. Possible selections are 1 s, 3 s, 5 s,
10 s or constant. If no project is available, the unit automatically switches to transfer
mode.
Proceed as follows
Proceed as follows to change the transfer settings:
1. Select the "Directories" tab.
2. Modify the entries
3. Discard or confirm the changes
4. Close the dialog
The Control Panel is displayed.
Note
Change during active transfer mode
If the HMI device is in transfer mode while changes are made to the transfer settings, the
settings only go into effect after the transfer function is restarted. This can occur when the
Control Panel is opened on the HMI device in order to modify the transfer properties.
See also
Runtime (Page 6-45)
6-44


6.6 Runtime
6.6
Runtime
The program parts required to run a project must be present on the HMI device. The transfer
is performed via
the Windows CE Image for TP 170micro and TP 170A
and via the project for TP 170B and OP 170B
Therefore:
No installation is needed on the HMI device.
The HMI device is immediately ready for use.
With a newer WinCC flexible version, it may be necessary to update the operating system.
See also
Updating the operating system (Page 7-19)

6-45

6.6 Runtime
6-46

Preparing and backing up a project

7.1
Transferring a project to an HMI device
7.1.1
Overview
Overview
Three procedures are available to transfer a project to the HMI device:
Transfer
During the transfer, it is possible to specifically select whether to transfer recipes,
passwords and compressed source files in addition to the project.
Restoring on the HMI device
During a restore process, a project stored on a memory card is transferred to the internal
Flash memory of the HMI device. A password list is not restored during the process.
Restoring from PC using ProSave
The backup project is transferred from a PC on line. This transfer includes recipes if any
have been saved. A password list is not restored during the process.
The procedures are the same both for the initial commissioning as well as recommissioning
of a project.

7-1

7.1 Transferring a project to an HMI device
Transfer and back transfer - backup and restore
1
Figure 7-1
Schematic display of transfer and back transfer or backup and restore
Configuration computer with source file *.hmi
Downloading and uploading
HMI device with project file *.fwx
Backup and Restore
Memory card with compressed source file *.pdz
See also
Start transfer (Page 7-6)
Backup and restore project (Page 7-13)
Restore project (Page 7-18)
7.1.2
Initial commissioning
Introduction
When commissioning for the first time, there is no project on the HMI device.
The procedure for transferring a project from the configuration computer to the HMI device,
is described in the sections "Transfer", "Backup and restore project for TP 170B and OP
170B on memory card" and "Restore project".
7-2


7.1 Transferring a project to an HMI device
7.1.3
Recommissioning
Introduction
When recommissioning, you replace an existing project on the HMI device with another. You
can transfer a project from the configuration computer to the HMI device to accomplish this.
The transfer is described in the section "Transfer."
The following options are available for switching the HMI device to transfer mode:
During the startup phase of the HMI device
Manual start of the transfer mode is activated by pressing "Transfer" in the loader.
During operation
Manual start of the transfer mode is activated by pressing an operator control in the
project.
During operation
Transfer mode is started automatically on the configuration computer.
The same project transfer options as those for initial commissioning are available.
See also
7.1.4
Setting the operating mode
Conditions for changing operating modes

In order to switch between the operating modes described below on the HMI device, the
relevant function must be configured and linked to an operating element.
Operating modes
The HMI device is designed for the following operating modes:
Offline mode
Online mode
Transfer mode
An operating element in the project can be used to set "Offline" and "Online" operating
modes on both the configuration computer and the HMI device.
Transfer mode must have been configured as an operating element.

7-3

7.2 Transfer
Offline mode
In this mode, there is no communication connection between the HMI device and PLC. The
HMI device can be operated but data cannot be transmitted to the PLC or received from the
PLC.
Online mode
In this mode, a communication connection between the HMI device and PLC exists. When
using this mode, processes in progress can be operated and visualized without restriction.
Transfer mode
In this mode, you can transfer a project from the configuration computer to the HMI device.
7.2
Transfer
7.2.1
Information and overview
Warning
Inadvertent transfer mode
Inadvertent transfer can trigger unwanted reactions on the system being monitored.
After the commissioning phase, deactivate the "Remote" or "Remote Control" checkbox in
the "Transfer Settings" dialog to prevent an inadvertent transfer on the HMI device.
Warning
Changes to the bus parameters
In the case of PROFIBUS DP, changes to the bus parameters in the loader under "S7Transfer Settings" should only be made for commissioning purposes. After activating
transfer mode on the HMI device, the HMI device only defines a standard bus parameter set.
In unfavorable conditions, this can lead to faults on the PROFIBUS DP bus.
In order to calculate the bus parameters exactly, the entire bus topology must be known.
Correct definition of the bus parameters for the project in the HMI device is automatically
ensured by the integrated operation of WinCC flexible in SIMATIC STEP 7.
7-4


7.2 Transfer
Notice
Transfer mode using MPI/PROFIBUS DP
For MPI/PROFIBUS DP transfer, the bus parameters, such as the MPI/PROFIBUS DP
address and baud rate, are read from the project currently active on the HMI device.
The settings for the MPI/PROFIBUS DP transfer should not be changed. The project must
first be stopped and the settings then changed via menu options "Control Panel > S7Transfer Settings". Then switch back to transfer mode.
When the project is restarted, the bus parameters for the selected profile "MPI" or
"PROFIBUS DP" are overwritten by the values in the project configuration.
Transfer settings
A project can only be transferred from the configuration computer to the HMI device when
the "Enable Channel" checkbox is activated in the "Transfer Settings" dialog.
If an interface is assigned to other programs, transfer cannot take place via this interface.
Transferable data
The following data can be optionally transferred to the HMI device:
the project, whereby a delta transfer is necessary.
Recipe data
the password list
Project source file for the TP 170B and OP 170B
Transferred data is written directly to the HMI device's Flash memory. The project source file
can also be transferred to the HMI device for processing a project later. Due to memory
capacity, the source file is not transferred to the internal Flash memory but to the memory
card.
To save transfer time, a delta transfer option is available for Windows CE HMI devices. In
the case of a delta transfer, only project data that has changed relative to the data on the
HMI device is transferred.

7-5

7.2 Transfer
7.2.2
Start transfer
Introduction
There are two different options for the transfer:
Manual transfer
Manual transfer means that the transfer mode must be started by the operator on the HMI
device. The manual transfer can also be started when the checkbox "Remote" or
"Remote control" is activated in the "Transfer Settings" dialog.
The HMI device can be switched to transfer mode manually while it is running. Manual
start is particularly advantageous when inadvertent activation of automatic transfer must
be ruled out.
Automatic transfer
Automatic transfer means that the transfer mode need not be started by the operator on
the HMI device.
The HMI device can be switched automatically to transfer mode during normal operation
as soon as transfer is started on the configuration computer connected. Automatic startup
is particularly suited for the test phase of a new project since transfer is completed
without interfering with the HMI device.
Note
A project running on the HMI device is always closed before a transfer begins.
Requirement
The HMI device is connected to a configuration computer.
7-6


7.2 Transfer
Proceed as follows
Proceed as follows:
The loader opens when the HMI device starts.
The following applies to manual transfer but not to automatic transfer:
2. Press "Transfer".
The "Transfer ..." dialog is displayed.
Figure 7-2
Proceed as follows on the configuration computer:
Notice
Remote control of the HMI device
When the checkbox "Remote" or "Remote Control" is activated in the "Transfer Settings"
dialog on the HMI device and the transfer is started on the configuration computer, a project
running on the HMI device will be closed.
3. Start transfer
The configuration computer checks the connection to the HMI device. If there is no
connection or the connection is faulty, an alarm appears on the configuration computer. If
the connection is correct, the selected data is transferred to the HMI device.
Warning
Inadvertent transfer mode
Inadvertent transfer can trigger unwanted reactions on the system being monitored.
After the commissioning phase, deactivate the "Remote" or "Remote Control" checkbox
in the "Transfer Settings" dialog to prevent an inadvertent transfer on the HMI device.
Result
When the transfer is successfully completed, the data is on the HMI device. The transferred
project is then started automatically.

7-7

7.2 Transfer
7.2.3
Testing project
Introduction
There are two options on the HMI device for testing a new project:
Test project offline
Testing offline means that communication between the HMI device and PLC is
interrupted while the test is being carried out.
Test project online
Testing online means that the HMI device and PLC communicate with each other during
the test.
It is advisable to perform both tests starting with the "Offline test" followed by the "Online
test."
Note
Testing on a configuration computer
A project can also be tested on a configuration computer using the Simulator. Detailed
information on this is available in the "WinCC flexible" user guide and in the WinCC flexible
online help.
You should always test the project afterwards on the HMI device where the project will be
used.
Check the following:

1. Check that configured screens are displayed correctly
2. Check screen hierarchy
3. Test input objects
4. Test softkeys
5. Tag data can be entered
The test increases the certainty that the project will run error-free on the HMI device.
Requirements for the offline test

The project is on the HMI device.
The project is offline.
To do this, open the project concerned on the configuration computer. Select
"Communication > Connections" and switch to "Online: Off". Transfer the project to the
HMI device.
Alternatively, the operating mode can be changed by means of an operating element in
the project. Use the operating element to switch the project offline.
7-8


7.2 Transfer
Note
During the test phase, it is recommended that the transfer operation be started during
operation.
Procedure
Use "Offline" mode to test the individual project functions on the HMI device without them
being affected by the PLC. PLC tags are, therefore, not updated.
Test the project operating elements and displays to the extent possible without connecting to
the PLC. Procedure:
1. Check configured object are displayed correctly
3. Check input fields
4. Test softkeys
Conditions for the online test

The project is on the HMI device.
The project is online.
To do this, open the project concerned on the configuration computer. Select
"Communication > Connections" and switch to "Online: On". Transfer the project to the
HMI device.
Alternatively, the operating mode can be changed by means of an operating element in
the project. Use the operating element to switch the project online.
Note
During the test phase, it is recommended that the transfer operation be started during
operation.
Procedure
Use "Online" mode to test the individual project functions on the HMI device with influence
being exerted by the PLC. PLC tags are updated in this case.
Test the project operating elements and displays. If offline testing has not yet been
performed, proceed as follows:
1. Check configured object are displayed correctly
3. Check input fields
4. Test softkeys

7-9

7.2 Transfer
Test all of the objects in the loaded project for which communication with the PLC is
necessary:
Alarms
Alarm logging
Recipes
Screen selection by PLC through PLC job
Print functions
See also
S7-Transfer Settings (Page 6-40)
Setting the operating mode (Page 7-3)
7.2.4
Transferring a project back using the TP 170B and OP 170B
Introduction
If the "Enable BackTransfer" checkbox is activated on the configuration computer for
transferring a project, the associated compressed source file is transferred during the
transfer process. The back transfer from the HMI device to the configuration computer can
then be performed.
After transferring a compressed source file back, it can be analyzed and modified when run.
This is of particular importance if
The original configuration computer cannot be accessed.
the project source file is no longer available.
Requirement
The following are requirements for the HMI device in order to transfer a project back:
The compressed source file associated with a project must be available on a memory
card which is inserted in the HMI device.
No project is open in WinCC flexible.
7-10


7.2 Transfer
Back transfer
Following the back transfer onto the configuration computer, the compressed source file is
decompressed by the WinCC flexible configuration software. The project is then available in
*.hmi format on the configuration computer and can be edited.
Notice
Version number
Once transferred back, the compressed source file can only be opened in the configuration
software when the following requirement is met:
The version number of the configuration software currently used is higher than or equal to
the version number of the configuration software used to create the project.
Test source file
There is not text on the HMI device or by WinCC to check if the project file on the HMI
device and the compressed source file on the memory card belong to the same project. If a
transfer is performed when the "Enable BackTransfer" option deactivated, only the project
file is transferred. Any source file on the memory card must therefore be from a previously
transferred project.
Proceed as follows
1. Select the menu options "Project > Transfer > Communication Settings" in WinCC
flexible.
The "Communication Settings" dialog box is opened.
2. Select the required connection type between the HMI device and configuration computer.
3. Define the connection parameters.
4. Select "Restore".
Proceed as follows on the HMI device:
1. Start the transfer mode in the loader.
1. On the configuration computer, use WinCC to start the back transfer using the "Project >
Transfer > Back Transfer" menu options.
This starts the back transfer.
Result
The uploaded project is opened on the configuration computer.

7-11

7.3 Backup and restore project for TP 170B and OP 170B on memory card
7.3
Backup and restore project for TP 170B and OP 170B on memory card
7.3.1
Overview
Introduction
Backup and restore for a project on the TP 170B and OP 170B can be made to a memory
card.
Data located on the HMI device can be saved and restored on the memory card of the HMI
device. Backup and restore can be performed even when there is no online connection to a
configuration computer.
The following data in the internal Flash memory can be saved and restored:
Project
Windows CE image
Password lists and recipe data lists, if these were saved in the internal Flash memory
In order to make a copy of a project or restore a saved project on the HMI device, open the
Control Panel and select the "Backup/Restore" dialog.
General notes
Notice
Power failure
If the restoring process is interrupted by a power failure on the HMI device, its operating
system is deleted. In this case, the operating system must be transferred again. Refer to the
"Update operating system" section.
Compatibility conflict
If a notification of a compatibility conflict appears on the HMI device during the restoring
process, the operating system must be updated.
See also
Loader (Page 6-5)
Configure operating system (Page 6-1)
7-12


7.3.2
Backup and restore project
Introduction
During a backup, the data is copied from the HMI device's Flash memory to a memory card.
The content of the memory card is overwritten following a system prompt.
When data is restored, the HMI device internal Flash card is deleted following a system
prompt. After deletion, the backup content of the memory card is copied onto the internal
Flash memory.
Notice
Password list
The password list is not saved during the backup.
Requirement
A memory card is required with a minimum memory capacity of 16 MB.
Procedure - backup
Proceed as follows:
1. Insert the memory card into the memory card slot.
2. Select "Backup/Restore" in the Control Panel
The "Backup/Restore" dialog opens.
If a memory card card is not insertedto the HMI device, the "No storage card detected"
alarm appears. Begin the procedure again from step 1.
Otherwise, the data backup will be started. If a data backup is already present on the
memory card, the alarm "You may have an old backup on the storage card" Do you want
to delete it?" is displayed..
Select "YES" to overwrite the existing data backup. Selecting "NO" terminates the
procedure.
Following the data backup, the message "Backup successfully completed" appears.
Press OK ...".
4. Press "OK".
5. Remove the memory card, if necessary.
This completes the backup.

7-13

Result
When the backup is successfully completed, a copy of the data on the HMI device is on the
memory card.
Note
Label the memory card (with date and version) and keep the memory card in a safe place.
Procedure - restore
Proceed as follows:
1. Insert the memory card into the memory card slot.
2. Select "Backup/Restore" in the Control Panel
The "Backup/Restore" dialog opens.
If a memory card card is not insertedto the HMI device, the "No storage card detected"
alarm appears. Begin the procedure again from step 1.
Otherwise, a data analysis is performed. In the meantime, the message "Checking data"
is displayed.
Following the data check, the following message appears: "You are starting RESTORE
now. All installed ...". This message warns you that all existing data, including the
registration data on the HMI device, will be deleted.
Selecting "YES" overwrites the data on the HMI device. Selecting "NO" terminates the
procedure.
4. Press "YES".
When the data restore process is completed, the following message appears: "Restore of
CE Image finished. The device ...". This informs you that the restore process is completed
although the memory card cannot yet be removed.
5. Press "OK".
The HMI device starts. Otherwise, another data analysis is performed. Following the data
check, the following message appears "Restore successfully finished. Press OK, remove
..." .
6. Removing the memory card
7. Press "OK".
The HMI device starts.
Result
When the restore is successfully completed, the data of the memory card is available on the
HMI device.
See also
Backup/Restore (Page 6-13)
7-14


7.4 ProSave
7.4
ProSave
7.4.1
Overview
ProSave service tool

The ProSave service tool is supplied on "WinCC flexible" installation CD. ProSave provides
all the functions which are necessary to transfer data between the configuration computer
and HMI device.
The following data can be backed up and restored like during the transfer:
Project
Recipe data
the password list
Project source file for the TP 170B and OP 170B
ProSave can operate integrated in WinCC flexible or as a standalone tool on the
ProSave In WinCC flexible

ProSave is installed on the configuration computer together with WinCC flexible. The entire
range of ProSave functions is then available in WinCC and ProSave dialogs can be opened
in the opened project.
All the necessary specifications, e.g. HMI device and transfer settings, are taken from the
project.
Standalone ProSave
ProSave can also be installed as a standalone application. In this case, information relating
to the HMI device and the transfer must be set in the user interface of ProSave. Ensure that
these settings agree with those in the HMI device.
The advantage of standalone ProSave is that backup and restore can be performed without
WinCC flexible via the following transfer channels:
Serial
MPI/PROFIBUS DP

7-15

7.4 ProSave
General notes
Notice
Power failure
If the restore process is interrupted by a power failure on the HMI device, its operating
system is deleted. In this case, the operating system must be transferred again. Refer to the
"Update operating system" section.
Compatibility conflict
If an alarm appears on the HMI device during the restore process indicating a compatibility
conflict, the operating system needs to be transferred again. Refer to the section "Update
operating system".
7.4.2
Backup project
Introduction
In the case of a backup process, the data to be saved is transferred from the HMI device
Flash memory to a configuration computer. The following procedures are possible using
ProSave:
Backup using standalone ProSave
Backup using WinCC flexible
The procedure for the backup differs in terms of the steps performed on the configuration
computer.
Requirement
ProSave is installed on the configuration computer.
All applications are closed on the configuration computer.
Procedure - backup using standalone ProSave

1. Start ProSave.
2. Use the "General" tab register to select the HMI device and connection type with
connection parameters.
3. Use the "Backup" tab to select the data to be saved:
"Recipes"
"Passwords"
"Complete Backup"
Only "Complete backup" is possible for the TP 170micro and TP 170A.
7-16


7.4 ProSave
4. Select the folder in which the *.psb backup file should be saved.
Define the required transfer channel on the HMI device and switch the HMI device to transfer
mode. Refer to the "Transfer" section.
1. Start the Backup process in ProSave with "Start Backup".
A status display appears indicating the progress of the backup process.
Procedure - backup using ProSave in WinCC flexible

1. Use "Project > Transfer > Transfer Settings" in WinCC flexible window "Select HMI
devices for transfer" to select the corresponding connection type with related connection
parameters.
2. Open the "Backup Settings" window in WinCC flexible using the menu commands
"Project > Transfer > Backup".
3. Select the data to be copied:
"Recipes"
"Passwords"
"Complete Backup"
Only "Complete backup" is possible for the TP 170micro and TP 170A.
4. Select the folder in which the *.psb backup file should be saved.
1. Start the backup process in WinCC flexible with "OK".
A status display appears indicating the progress of the backup process.
Result
When the backup is successfully completed, an alarm appears. The project is copied on the

7-17

7.4 ProSave
7.4.3
Restore project
Introduction
During a restore process, a project data from the configuration computer is transferred to the
internal Flash memory of the HMI device. The following procedures are possible using
ProSave:
Restore using standalone ProSave
Restore using ProSave in WinCC flexible
The procedure for the restore process differs in terms of the steps performed on the
Notice
Data loss
The data in the internal Flash memory of the HMI device is deleted during restore.
Requirement
All applications are closed on the configuration computer.
Procedure - restore using standalone ProSave

1. Start ProSave.
2. Use the "General" tab register to select the HMI device and connection type with
connection parameters.
3. In the the "Restore" tab, select the directory containing the source file to be restored.
"Content" indicates the HMI device is involved and the type of backup data contained in
the selected file.
1. Start the restore process in ProSave with "Start Restore".
A status display appears indicating the progress of the restore process.
7-18


7.4 ProSave
Procedure - restore using ProSave in WinCC flexible

1. In WinCC flexible use the menu command "File > Transfer > Settings" in the "Transfer
Settings" window to select the connection type with corresponding connection
parameters.
2. Open "Restore" in WinCC using the menu command "File > Transfer > Restore".
3. In the the "Restore" tab, select the directory containing the file to be restored.
"Content" indicates the HMI device is involved and the type of backup data contained in
the selected file.
1. Start the restore process in WinCC flexible with "OK".
A status display appears indicating the progress of the restore process.
Result
When the restore is successfully completed, a message appears. The project is restored on
the HMI device.
7.4.4
Introduction
When a new project is transferred to the HMI device, a compatibility conflict can arise due to
the different versions of the configuration software and the image on the HMI device. In such
a case, transfer of the project is stopped by the configuration computer and a message
indicating a compatibility conflict appears. The operating system on the HMI device must
then be updated. For this purpose, a current image must be transferred to the HMI device.
The necessary operating system is transferred together with the image.
The service tool ProSave can be used for the update if the HMI device has no operating
system or no functioning operating system - and even when there is an operating system.
Note
For the TP 170B and OP 170B, refer to the Control Panel "System Properties" dialog to see
the version of the image loaded on the HMI device.

7-19

7.4 ProSave
Requirement
The associated data channel is configured.
Notice
Data loss
When an operating system is updated, all of the data on the HMI device is deleted. Data
on a memory card in the HMI device remains unaffected.
If no image or no operable image appears on the HMI device, the operating system must
be updated via the RS 232 interface.
Procedure update operating system without booting

When the operating system is updated without booting, the configuration computer
communicates with the HMI device using its operating system.
1. Start WinCC flexible via the Windows Start menu and open a project or start ProSave via
the Windows Start menu.
2. In WinCC flexible, select the menu options "Project > Transfer > Transfer Settings" or
select the HMI device available on the "General" tab in ProSave.
3. Select a connection.
4. Enter the connection parameters.
5. In WinCC flexible, select the menu options "Project > Transfer > Update Operating
System" or select the "OS Update" tab in ProSave.
6. Deactivate the "Booting" checkbox if it is already activated.
7. In "Imagepath", select the directory containing the image file, *.img, for the HMI device.
"Drive:\...\Siemens\SIMATIC WinCC flexible\WinCC flexible Images\Mobile_OP_TP170B
8. Select "Open".
When the image file has been opened successfully, various information related to the
version appears in a window.
1. Start the operating system transfer with "Update OS".
This process takes a different length of time, depending on the data channel selected. A
status display monitors the progress of the transfer.
7-20


7.4 ProSave
Procedure update operating system with booting

When updating the operating system with "bootstraping", ProSave communicates with the
boot loader of the HMI device.
Notice
An operating system update with "bootstraping" is only possible via the serial interface.
After starting the operating system transfer, the HMI device must be rebooted for the HMI
device to establish contact via the serial interface.
Switch off the HMI device.
1. In WinCC flexible, select the menu options "Project > Transfer > Transfer Settings" or
select the HMI device available on the "General" tab in ProSave.
2. Select a connection.
3. Enter the connection parameters.
4. In WinCC flexible, select the menu options "Project > Transfer > Update Operating
System" or select the "OS Update" tab in ProSave.
5. Activate the "Booting" checkbox if it is deactivated.
6. In "Imagepath", select the directory containing the image file, *.img, for the HMI device.
"Drive:\...\Siemens\SIMATIC WinCC flexible\WinCC flexible Images\Mobile_OP_TP170B
7. Select "Open".
When the image file has been opened successfully, various information related to the
version appears in a window.
8. Start the operating system transfer with "Update OS".
Switch on the HMI device. This starts the transfer. A status display monitors the progress of
the transfer.
Result
When the operating system update is successfully completed, an message appears. There
is no longer a project on the HMI device.
See also
OP (Page 6-23)
Connecting the configuration computer (Page 4-12)

7-21

7.4 ProSave
7-22

Runtime functionalities of a project

8.1
Screen objects
Overview
Runtime offers the following objects for operator control and display:
Screen object
TP 170micro, TP 170A
TP 170B, OP 170B
Button
Yes
Yes
Switch
Yes
Yes
IO field
Yes
Yes
Graphic IO field
Yes
Yes
Symbolic IO field
Yes
Yes
Alarm indicator
Yes
Alarm view
Yes
Simple alarm view
Yes
Yes
Alarm window
Yes
Yes
Recipes view
Yes
Simple recipe view

Bar
Trend view
Date/time field
Yes
Yes
Yes
Yes
Yes
Yes
User view
Yes
Simple user view
Yes

8-1

8.2 Alarms
8.2
Alarms
Alarm classes
Alarms indicate events and states in the control process on the HMI. WinCC flexible
distinguishes between the following alarm classes:
Operation
Warning alarms indicate a process status, e.g. motor is ON. Warning alarms are
configured.
Error
Error alarms indicate operational malfunctions such as excess motor temperature. Error
alarms are configured. Because of their importance, error alarms must be acknowledged.
System
System alarms are triggered by the HMI device. They are not configured. System alarms
provide information on occurrences such as operator errors or communication faults.
STEP 7 alarm classes
The alarm classes configured in STEP 7 are also available for the HMI device.
Custom alarm classes
It is possible to configure additional alarm classes.
Alarm buffer
All incoming, outgoing, and acknowledged alarm events are stored in an internal volatile
buffer. The size of this alarm buffer depends on the type of HMI device.
Alarm report (TP 170B and OP 170B only)

If alarm reporting is activated, alarm events are sent directly to the connected printer.
It is possible to individually configure each alarm to specify whether it is to be reported (sent
to the printer).
8-2


8.3 Tags
Alarm view
Events stored in the alarm buffer and the alarm log can be displayed in the alarm view in
Runtime.
The alarm view is used to display alarms providing information on events that have occurred
in a process. Whether alarm events have to be acknowledged or not is specified in your
configuration.
Alarm window
If configured, an alarm window shows all pending alarms or alarms awaiting
acknowledgement of a particular alarm class. The alarm window is displayed as soon as a
new alarm occurs.
You can configure the order in which the alarms are displayed. You can choose to display
the alarms in ascending or descending order of their occurrence. The alarm window can also
be set to indicate the exact location of the fault, including the date and time of the alarm
event.
Alarm indicator (TP 170B and OP 170B only)

An alarm indicator is a graphical symbol that is displayed on the screen if at least one error
alarm is still pending on the HMI device.
The alarm indicator flashes as long as unacknowledged alarms are pending. The displayed
number indicates the number of pending alarms.
8.3
Tags
Definition
Tags represent defined memory areas on the HMI device, to which values are written and/or
from which values are read. This action can be initiated on the controller, or by the operator
at the HMI device.
8.4
System functions
Application
System functions are used in Runtime for the following purposes:
To control the process
To utilize the properties of the HMI device
To make system settings on the HMI device online
In WinCC flexible, all system functions and scripts are linked to an object, such as a button,
key, or screen, and an event. As soon as the event occurs, the system function is triggered.

8-3

8.5 Safety
System functions
System functions are predefined functions that are used to implement many tasks in
Runtime, such as:
Calculations, e.g. increase of a tag value by a specific or variable amount
Settings, such as changing the PLC or setting a bit in the PLC.
Alarms, for instance after logon of a different user.
Events
The object and the selected function determine what events can be defined as triggers for
executing a system function.
For example, the events "Change value", "BelowLowerLimit" and "AboveUpperLimit" belong
to the "Tag" object. The "Loaded" and "Cleared" events are associated with the "Screen"
object.
8.5
Safety
Overview
Operation in Runtime is protected by the use of user groups, passwords, and log-off times.
After Runtime starts, you enter the user name and password in the logon dialog.
Figure 8-1
Logon dialog (TP 170B and OP 170B only)
Note
No default logon dialog is available for TP 170micro and for TP 170A.
For these HMI devices, use a screen created by the project engineer for logging on and off.
The system functions "Logon" and "Logoff" are used for this.
8-4


8.5 Safety
User groups
The security concept of WinCC flexible has multiple levels for TP 170B and OP 170B: It is
based on authorizations, user groups, and users.
User groups are created for specific projects by the configuring engineer. The
"Administrators" group is included in all projects by default. User groups are assigned
authorizations. The authorization level required for an operation is specifically defined for
each individual object and function in the project.
User accounts are created by the configuring engineer and in Runtime by the
administrator, or by a user with the same rights, and are always assigned to one group
only.
Users belonging to a user group with "Administration" authorization may create further user
accounts and assign these to a group.
Note
Except for the user "Admin" and the group "Administrators," no other users or user groups
may be used for TP 170micro and for TP 170A.
Passwords
Only registered users may log on to Runtime by entering their user name and password. The
passwords can be assigned by the configuring engineer, by the "Admin" user (or by users
who have "Administration" authorization), or by the user himself.
Which functions a user may execute after he/she logs on depends on his/her user group
assignment.
After the project is transferred, only the administrator is authorized to create user accounts,
make user group assignments, and change passwords. Any other users who are
subsequently assigned to the "Administrator" group by the administrator may also carry out
these tasks.
The list will be encrypted and saved on the HMI device to protect it from loss due to a power
failure.
Note
Depending on the transfer settings, changes to the password list are overwritten when the
project is transferred again.
Logoff times
A logoff time is specified in the system for each user. If the time between any two user
actions, e.g, entering a value or pressing a key, exceeds this logoff time, the user is
automatically logged off. The user must then log on again to continue to operate Runtime.

8-5

8.5 Safety
User view (TP 170B and OP 170B only)

Use the User view to display the users present on the HMI device.
Export and import

All users, passwords, group assignments and logoff times furnished on the HMI device can
be exported and reimported on another HMI device, when the configuration is suitable. This
allows you to avoid entering all of the data again on another HMI device.
Notice
The currently valid passwords are overwritten during an import. The imported passwords are
valid immediately.
8-6


8.6 Other operating functions
8.6
Other operating functions
Printing functions (TP 170B and OP 170B only)

The following print functions are available on the HMI device:
Hardcopy
You can print the content of the currently displayed screen if you utilize the "Print screen"
system function in your configuration.
Alarm report
Each alarm event that occurs (incoming, outgoing, acknowledgment) is also sent to a
printer.
Note
Special, non-European characters
When printing non-West European alarms, some characters are not printed under certain
circumstances. The printing results depend on the character set of the printer used.
LED control
The light-emitting diodes (LED) in the function keys of the SIMATIC HMI devices can be
controlled from the PLC. For example, an illuminated or flashing LED can signal the operator
to press a specific function key on the device.

8-7

8.6 Other operating functions
8-8

Operating a project
9.1
Basic principles of operation
9.1.1
Basics for operation in Runtime
Introduction
The process control features are defined by the project configuration and the options
available on the HMI device. This section contains general information on the settings for
Runtime and for operation of predefined screen objects.
Screen objects provide general system functions. Screen objects can be used and
configured in screens in the project.
Runtime can be controlled with the keys, using the touch screen, or via the keyboard and
mouse, depending on the HMI device used.
Multiple key operation

Unintentional actions can be triggered by a multiple key operation.
When you use a key device, you may not press more than two function keys
simultaneously.
If you are using a touch screen device, you may only operate one touch object at a time.

9-1
Operating a project
9.1 Basic principles of operation
Language switching
WinCC flexible allows a multilingual project configuration. Up to five of these project
languages can be loaded on the HMI device simultaneously.
Runtime allows you to change the languages, provided this function is configured.
Language-specific objects such as texts or formats are localized. The following objects may
contain language-relevant texts, for example:
Alarms
Screens
Text lists
Operator notes
Recipes
Date/time
Static texts
Objects in the template screen

Objects that should be available on each screen are configured in the template by the
configuring engineer, e.g., important process values or date and time.
An operating element that is present in the template is available in every screen. In the case
of touch screen devices, for example, a button in the template screen simulates a globally
effective function key.
Pictograms
In the case of keyboard devices, pictograms can be configured along the bottom and sides
of the screen.
Pictograms highlight the screen-specific functions of the function keys. Activating the
associated function key initiates the function symbolized by the pictogram.
9-2

Operating a project
9.1.2
Operating the touch screen device
9.1.2.1
Operating touch objects
Operation
Touch objects are touch-sensitive operating objects on the HMI screen, e.g. buttons, I/O
fields and alarm windows. The operation of these is basically no different than the operation
of conventional keys. You operate these objects by touching them with the finger.
Caution
Always touch only one object on the screen. Do not touch several touch objects
simultaneously. You may trigger an unintended action.
Caution
Do not use any pointed or sharp objects when operating the touch screen in order to avoid
damaging the plastic surface.
Direct keys
With a PROFIBUS DP connection, it is also possible to configure buttons for operation as
direct keys in order to allow rapid operator inputs using keys. Rapid button operation is
conditional for jog mode, for example.
PROFIBUS-DP direct keys place bits directly from the HMI device in the I/O area of a
SIMATIC S7.
Note
With touch operation, direct keys are triggered independent of any configured password
protection. Therefore, do not use password protection for direct keys.
Notice
Direct keys are still active when the HMI device is in the "offline" mode.
Button action feedback

The HMI device outputs an acoustic and optical signal as soon as it detects the operation of
a touch object. This feedback is always output, irrespective of communication with the PLC.
Therefore, this feedback does not indicate whether the relevant action is actually executed or
not.

9-3
Operating a project
Visual feedback
The type of visual feedback depends on the operated touch object:
Buttons
The HMI outputs different indications of the "Touched" and "Not touched" states, provided
the programmer has configured a 3D effect:
Touched
Untouched
The programmer defines the layout of a selected field (line width and color of the focus.)
Hidden buttons
The focus of hidden buttons is not set after marking (focus width value is 0, default.) In
Runtime, the outline of a touched button is indicated as a line when you modify the focus
with value in the configuration data. This outline remains visible until the focus is set on
another operating object.
I/O fields
After you touch an I/O field, a screen keyboard appears as a feedback signal.
Operating screen objects with buttons

Screen objects with predefined buttons can also be operated with external buttons. The
requires the programmer to have linked the relevant system functions to these buttons.
In WinCC flexible, these system functions are organized in the "Keyboard actions for screen
objects" group.
9.1.2.2
Input of values
On-screen keyboard
The HMI device automatically opens the screen keyboard when you touch an input object
such as an I/O field. This screen keyboard is also displayed to input of passwords for access
to protected functions. The keyboard is automatically hidden again when input is complete.
Based on the configuration of the input object, the HMI device shows a screen keyboard only
for the input of numeric or alphanumeric values.
The screen keyboard is activated by selecting an input object in runtime.
9-4

Operating a project
9.1.2.3
Inputting numeric values
Numeric screen keyboard

The HMI device automatically opens the numeric screen keyboard for the input of numeric
values when you touch an I/O field on the screen. The HMI automatically hides the keyboard
again when input is complete.
Figure 9-1
Example of on-screen keyboard for numeric inputs
The <Help> button is only active if an operator note is configured for the I/O field.
The <BSP> key corresponds to the <Backspace> key; it deletes the character to the left of
the current cursor position.
On the on-screen keyboard, you can only operate the keys shown in the 3D display.
Operability of keys is dependent on the type of value that is to be input.
Procedure
You enter numeric and hexadecimal values character-by-character using the on-screen
keyboard buttons. You confirm the value entered by pressing <Enter> or cancel it by
pressing <ESC>. Both functions will close the screen keyboard.
Note
The numeric input fields may be assigned limits. In this case, the system accepts only the
values which lie within the configured range. The system rejects any values which are out of
these limits and restores the original value. In this case, the HMI outputs a system alarm.
When the on-screen keyboard is displayed, the upper and lower limit values are displayed, if
configured.

9-5
Operating a project
Note
When the on-screen keyboard is open, PLC job 51, "Select Screen" has no function.
9.1.2.4
Inputting alphanumeric values
Alphanumeric screen keyboard

The HMI automatically opens an alphanumeric keyboard for the input of strings and numeric
values in hex format when you touch an input object on the screen. The HMI automatically
hides the keyboard again when input is complete.
Figure 9-2
Screen keyboard for alphanumeric input
The <Help> is only active if an operator note is programmed for the input object.
The <BSP> key corresponds to the <Backspace> key; it deletes the character to the left of
the current cursor position.
Keyboard layers
The alphanumeric keyboard is organized in several layers:
Standard layer (refer to figure)
<Shift> layer
9-6

Operating a project
Procedure
You use the screen keyboard buttons to input the characters of alphanumeric values. You
confirm the value entered by pressing <Enter> or cancel it by pressing <ESC>. Both
functions will close the screen keyboard.
Note
When the on-screen keyboard is open, PLC job "Select Screen" has no function.
9.1.2.5
Opening an operator note (TP 170B and OP 170B only)
Purpose
The operator notes provide additional information and operating instructions with respect to
alarms, screen and operable screen objects to the programmer. A operator note may contain
information about the permissible range of values for an I/O field, or information on the
causes of alarm events and their elimination.
Figure 9-3
Operator note for an I/O field (Example)
Help on messages
Actuate the
button on the alarm screen or in the alarm view
Help on input objects

Touch the <Help> button on the screen keyboard. This button is only available if you
configured an operator note.
Help on the current screen

Call the operator note for the current screen

9-7
Operating a project
Note
To view a new operator note, you first need to close the window showing the current
operator note.
9.1.3
Operating a keyboard device
9.1.3.1
Functions of the system keys
Overview of system key functions

Key
Function
Purpose
Shift (digits/letters)
Toggles the assignment from numbers to letters.

No LED is lit:
A-Z
The number assignment is enabled. One actuation of the button

toggles to letter assignment.
One LED is lit:
The left or right letter assignment is enabled.
Each time the key is pressed, the system toggles between the right
letter assignment and number assignment.
Deleting characters
Deletes the character at the current cursor position.
Cancel
Deletes the input characters of a value and restores the original

value.
Closes the active window.
INS
DEL
ESC
Acknowledge
ACK
Acknowledges the currently displayed error alarm or all alarms of an

acknowledgement group (group acknowledgement.)
The LED is lit as long as unacknowledged error alarms are queued.
Display operator notes
Opens the configured operator note for the selected object (e.g. a
alarm, I/O field.) The LED signals an that an operator note exists for
the selected object.
Enter
Tabulator
Selects the next available screen object in the configured tab

sequence.
Deleting characters
Deletes the character to the left of the current cursor position.
HELP
ENTER
TAB
9-8
Applies and closes the input

Opens a drop-down list for symbolic I/O fields
Triggers buttons

Operating a project
Key
Function
Purpose
Moving the cursor
Selects the next operable screen object on the right or left, above
or below the current screen object.
Navigates in the screen object.
Scrolling back
Scrolls one page down.
Scrolling up
Scrolls one page up.
Shift
(upper/lower case)
Use in key combinations, for example, for switching to uppercase

letters.
General control functions
Used in key combinations, for example, for navigating through trend

views.
General control functions
Used in key combinations, for example, for the "Status force" screen
object.
HOME
END
SHIFT
CTRL
ALT
9.1.3.2
Functions of the key combinations
General operation
Navigation
Shortcut keys
SHIFT
SHIFT
SHIFT
SHIFT
SHIFT
ALT
TAB
Function
Selects the previously available screen object in the configured tab sequence.
Positions the cursor within a screen object, for example, in an I/O field.
Opens a selection list.

9-9
Operating a project
Monitor screen settings

Shortcut keys
A-Z
A-Z
Function
Reduces the screen contrast.
Increases the screen contrast.
In the startup phase

Shortcut keys
Function
Toggles the HMI device to "transfer" mode.
ESC
You can always exit transfer mode provided the unit is currently not transferring
any data.
Dialogs
Shortcut keys
Jumps to the next field.
TAB
SHIFT
Function
TAB
Jumps to the previous field.
Opens the next tab if the focus is set on the name

of this tab.
Opens the previous tab if the focus is set on the
name of this tab.
ESC
Closes the dialog without saving.
Operating screen objects with softkeys

You may also operate screen objects with buttons, e.g. the alarm view, trend view, recipe
view or status force, using softkeys. The programmer must have linked the corresponding
system function to the softkey.
In WinCC flexible, these functions are organized in the "Keyboard actions for screen objects"
group.
9-10

Operating a project
9.1.3.3
Calling the operator note
Purpose
The configuring engineer uses operator notes to provide additional information and operating
instructions with respect to alarms, screens, and operable screen objects. An operator note
may contain information about the permissible range of values for an I/O field (refer to figure
below) or, in the case of an alarm, information on the causes of an alarm event and its
elimination.
Figure 9-4
Operator note for an I/O field (Example)
Procedure
To display the operator note configured for an I/O field:
1. Select the I/O field, e.g.
The I/O field is selected. The LED signal of the

available.
2. Press
HELP
HELP
key indicates that an operator note is
to display the operator note.
The operator note is shown in the language currently set on the HMI device. Any operator
note configured for the current screen is shown when you press the key again.
3. Close the Help window with the
ESC
key or by pressing the
HELP
key again.
Note
To view a new operator note, you first need to close the window showing the current
operator note.

9-11
Operating a project
9.2 Operating graphic objects
9.1.4
Close the project.
Proceed as follows
Notice
Data loss
If a memory card is inserted in the HMI device, close the project before switching off the
power supply for the HMI device.
Proceed as follows:
1. Close the project using the operator control configured for this purpose.
Wait until the loader is displayed after runtime is stopped.
2. Switch off the power supply to the HMI device.
If the HMI device is inadvertently switched off during operation, the memory card is checked
when it restarts. The defect memory areas on the card are repaired during the process.
9.2
Operating graphic objects
9.2.1
Button
9.2.1.1
Description
Purpose
A button is a virtual key on the screen of the HMI device that can have one or more
functions.
You can initiate separate, independent functions with the following button operations:
Press
Release
Activate the button in the tab sequence
Deactivate the button in the tab sequence
9-12

Operating a project
Layout
A button can be labeled, use a graphic symbol or be hidden.
The operation may be followed with a visual feedback. However, note that the optical
feedback only indicates a completed operation and not whether the configured functions
were actually executed.
9.2.1.2
Touch control
Procedure
Touch the button on the touch screen of the HMI device.
9.2.1.3
Keyboard control
Procedure
To operate a button with a keyboard:
Use the cursor to select the button, e.g.
Then press
9.2.2
Switch
9.2.2.1
Description
ENTER
or
Purpose
The switch is an control object and display object with two states: "pressed" and "released."
Switches can signal the state of a system component that cannot be seen from the HMI
device, e.g. a motor. You can also change the status of that system components at the HMI
device.
A switch has two stable states: When you actuate the switch, it changes to the other state.
The switch retains this status until the next operation.

9-13
Operating a project
Layout
A switch can be labeled with a descriptive name, e.g. "Motor 2" and/or the names of its two
states, e.g. "ON" and "OFF". The switch can be positioned vertically or horizontally.
9.2.2.2
Touch control
Procedure
Touch operation of a switch differs depending on the switch type:
If a slider is displayed for the switch:
Move the slider on the touch screen of the HMI device to the new position, or double-click
the slider area.
If only a text or a graphic is displayed for the switch:
Touch the switch on the touch screen of the HMI device.
9.2.2.3
Keyboard control
Procedure
To operate a switch with a keyboard:
Select the switch with a cursor key, e.g.
Then press
9.2.3
IO field
9.2.3.1
Description
ENTER
or
Purpose
You enter numeric or alphanumeric values in an IO field. An example of a numerical value is
the number 80 as setpoint for a temperature. An alphanumeric value is the text "Service" as
user name.
9-14

Operating a project
Layout
The layout of an IO field depends on its configuration in WinCC flexible, e.g.:
Numeric IO field
For input of numbers in decimal, hexadecimal or binary format.
Alphanumeric IO field
For input of character chains
IO field for date and time
For input of calendar dates or time information. The format depends on the language set
on the HMI device.
IO field for password input
For concealed input of a password. The input character string is displayed with
placeholders (*).
Behavior
If limit values are configured for the tag that is linked to the IO field, the input value is only
applied if the value is within the configured limits.
Any input values which are out of range are rejected. The original value is displayed on the
IO field instead, and a system alarm is output on the HMI device.
9.2.3.2
Touch control
Procedure
Press the IO field on the touch screen of the HMI device. The screen keyboard automatically
appears. Enter the desired value using the screen keyboard. Confirm your input with <Enter>
or cancel it with <Esc>. After the input has been confirmed or canceled, the screen keyboard
is automatically closed.
9.2.3.3
Keyboard control
Procedure
Enable the I/O field with one or several
TAB
according to the configured tab sequence. The
selection is signaled by the colored field content.

You now have two options:
Position the cursor with
SHIFT
and a cursor key. The selection of the field content is
cancelled. Type in the relevant value.

9-15
Operating a project
Press
ENTER
. The object changes to the specific editing mode. Now, only one character will
be marked in the field.

You can use the
/
The
cursor keys to scroll the character table.
cursor keys can be used to move to the next or previous input
position.
Confirm your entry with
ENTER
or cancel it with
ESC
Note
To enter the hexadecimal characters "A" to "F" for numerical values, toggle the input keys
using
A-Z
to activate the letter assignment.
9.2.4
Graphic IO field
9.2.4.1
Description
Purpose
In a graphic IO field, select a predefined image from a selection list. The graphic represents
the value of a tag. This can be an internal tag or a tag with a connection to a PLC.
The graphic IO field can also be used merely to output a pure graphic depending on the
value of a tag. In this case, you cannot then operate the graphic IO field.
Layout
If the graphic IO field shows a cactus icon, you have not defined the graphic output of a
specific value in your project.
9-16

Operating a project
9.2.4.2
Touch control
Procedure
Touch the graphic IO field on the touch screen of the HMI device. Selection mode is
activated.
Select the desired graphic using the scroll bar.
Apply the required graphic by touching it, or reject the selection by touching another screen
object.
9.2.4.3
Keyboard control
Procedure
Operating a graphic I/O field on a keyboard device:
Step
Procedure
Select the graphic I/O field
Activate selection mode
Select the entry
Accept the selection
e.g.
ENTER

The selection mode is activated.

Moves the cursor by lines.
ENTER
The selected entry is now valid. The

selection mode is closed.
or
Cancel the selection
The graphic I/O field is marked.
ESC
The function restores the original value.
9-17
Operating a project
9.2.5
Symbolic IO field
9.2.5.1
Description
Purpose
In a symbolic IO field select a predefined entry from a selection list. The entry represents the
value of a tag. This can be an internal tag or a tag with a connection to a PLC.
The symbolic IO field can also be used to merely output an entry depending on the value of
a tag. In this case, the symbolic IO field can no longer be operated.
Layout
If the symbolic IO field contains a blank text line in the drop-down list, you have not defined a
relevant entry in the project.
9.2.5.2
Touch control
Procedure
Touch the symbolic IO field on the touch screen of the HMI device. The predefined entries
are displayed in the selection list.
If the selection list has a scroll bar: Touch the scroll bar on the touch screen of the HMI
device. Touch the touch screen continuously to move the scroll bar in the desired direction.
Select the desired entry and apply the associated tag value by touching the entry on the
touch screen. The selection list is closed and the entry is displayed. The symbolic IO field
continues to have the focus.
9-18

Operating a project
9.2.5.3
Keyboard control
Procedure
To operate a symbolic I/O field with a keyboard:
Step
Procedure
Select the symbolic I/O field
Opens the selection list.
Select the entry
Accept the selection
e.g.
ENTER
The drop-down list opens.
Moves the cursor by lines.
ENTER
The selected entry is now valid. The

drop-down list is closed.
or
Cancel the selection
The symbolic I/O field is marked.
ESC
9.2.6
Alarm indicator (TP 170B and OP 170B only)
9.2.6.1
Description
The function restores the original value.

The drop-down list is closed.
Purpose
The alarm indicator is a configurable graphic icon that is displayed on the screen as long as
at least one alarm belonging to the specified alarm classes is pending on the HMI device.

9-19
Operating a project
Behavior
The alarm indicator flashes as long as unacknowledged alarms are pending. The displayed
number indicates the number of pending alarms.
Note
The icons from the symbol library can only be operated by touch screen.
9.2.6.2
Touch control
Procedure
Touch the alarm indicator. An alarm window opens depending on the configuration.
Use the Close icon to close the Alarm window and be able to operate the screens. The alarm
window can be opened again by touching the alarm indicator.
9.2.7
Alarm view (TP 170B and OP 170B only)
9.2.7.1
Description
Purpose
The Alarm view shows alarms or alarm events selected by the planner from the alarm buffer
or, if supported by the HMI device, from the alarm log.
Layout
To be able to distinguish between different alarms classes, they are identified in the first
column of the Alarm view:
Icon
Alarm class
Error
(empty)
Operation
(depending on configuration)
Custom alarm classes
System
In Runtime you can configure the column order and the sorting order of each column.
9-20

Operating a project
Operator controls
The buttons have the following functions:
Button
Function
Use this button to call the configured operator note for the selected alarm.
This button triggers the function assigned to the "Edit" event for the selected
alarm.
This button is used to acknowledge an unacknowledged alarm.
9.2.7.2
Touch control
Procedure
Touch the desired operating element in the Alarm view on the touch screen of the HMI
device.
Changing column sequence and sorting sequence

In Runtime you can configure the column order and the sorting order of each column.
Change column sequence
To reverse the "Time" and "Date" columns, for example, touch the "Date" header on the
HMI device touchscreen. Continue to press the touchscreen and drag the column
heading to the "Time" heading.
Change sorting order
To change the chronological order of the alarms, touch the column heading, "Time" or
"Date" on the HMI device's touchscreen.
9.2.7.3
Keyboard control
Procedure
There is also a tab order in the alarm view for the list showing displayed alarms and all
configured buttons.
Proceed as follows to acknowledge an alarm using the keys.
1. Activate the alarm view using
TAB
, according to the tab order.
2. Select the alarm to be acknowledged. The
HOME
END
and
keys can be used
for this.

9-21
Operating a project
3. Press and hold the

4. Press the
ENTER
9.2.8
Simple alarm view
9.2.8.1
Description
TAB
key until the button to be acknowledged is selected.
key.
Purpose
On an HMI device with a small display, the simple alarm view is used to display and edit
alarms.
Layout
The display of the simple alarm view depends on the configuration.
The display shows all current, departed or acknowledged alarms of the selected alarm
classes.
The number of lines per alarm and the visible lines.
9-22

Operating a project
Operator controls
Button
Function
This button is used to acknowledge an unacknowledged alarm.
This button triggers the function assigned to the "Edit" event for the selected alarm.
Use this button to call the configured operator note for the selected alarm.
9.2.8.2
Touch control
Procedure
Touch the desired control object in the alarm view on the touch screen of the HMI device.
9.2.8.3
Keyboard control
Procedure
The simple alarm view also has a tab order for the list showing displayed alarms and all
configured buttons.
Proceed as follows to acknowledge an alarm using the keys.
1. Activate the simple alarm view using
TAB
, according to the tab order.
2. Select the alarm to be acknowledged. The

for this.
3. Press and hold the
4. Press the
ENTER
TAB
HOME
END
and
keys can be used
key until the button to be acknowledged is selected.
key.

9-23
Operating a project
9.2.9
Bar
Purpose
The bar is a dynamic display object. The bar displays a value from the PLC as a rectangular
area. The operator at the HMI device can thus see immediately how far the current value is
from the configured limit value or whether a setpoint value has been reached. The bar can
display values such as fill levels or batch counts.
Layout
The layout of the bar is set in the user program. In the bar, for example, lines can identify the
configured limit values. Color changes can signal when a limit value has been exceeded or
not been met.
Operation
The bar is for display only and cannot be controlled by the operator.
9-24

Operating a project
9.2.10
Trend view (TP 170B and OP 170B only)
9.2.10.1
Description
Purpose
The trend view is a dynamic display object. The Trend view can display actual process data
and process data from a log continuously when it is supported by the HMI device.
Layout
The layout of the trend view is based on the configuration. A trend view can show multiple
curves simultaneously to allow the user, for example, to compare different process
sequences. If the displayed process value exceeds or falls below the configured limit values,
the violation of the limit can be displayed by a change of color in the curve.
A ruler can also simplify the reading of the process values from the trend view. The ruler
displays the Y-value that belongs to an X-value.
Operator controls
The trend view is operated by the configured trend display buttons. If no buttons have been
configured for the trend view, you can operate the trend view using the keyboard or the
function keys of the HMI device. Prerequisite is that the project engineer has configured and
documented this type of operation.
Operator control
element
Function
Scrolls back to the beginning of the trend recording. The start values of the trend recording are
displayed there.
Zooms the displayed time section

9-25
Operating a project
Operator control
element
Function
Zooms out of the displayed time section
Moves the ruler backward (to the left).
Moves the ruler forward (to the right).
Scrolls one display width backward (to the left).
Scrolls one display width forward (to the right).
Shows or hides the ruler. The ruler displays the X-value associated with a Y-value.
Stops or continues trend recording
9.2.10.2
Touch control
Procedure
Touch the desired control object in the trend view on the touch screen of the HMI device.
9.2.10.3
Keyboard control
Procedure
Activate the trend view with
TAB
using the tab order configured.
The table below shows the available shortcut keys.

Keys
CTRL
9-26
Function
ENTER
the trend recording are displayed there.

Y
CTRL
CTRL
Scrolls back to the beginning of the trend recording. The start values of
Zooms the displayed time section.
Zooms out of the displayed time section.

Operating a project
Keys
Function
CTRL
ALT
CTRL
ALT
SHIFT
SHIFT
9.2.11
Date/time field
9.2.11.1
Description
Moves the ruler backward (to the left).
Moves the ruler forward (to the right).
Scrolls one display width backward (to the left).
Scrolls one display width forward (to the right).
Purpose
The date / time field indicates the system time and data. In Runtime, you may change the
system time and data in accordance with the configuration.
Layout
The layout in the date/time field depends on the language set in the HMI device.
Behavior
An input values other than the date and system time are rejected. Instead, the original values
(plus the time that has elapsed in the meantime) will appear in the date/time field and a
system alarm will be displayed on the HMI device.
9.2.11.2
Touch control
Procedure
Touch the date/time field on the touch screen of the HMI device. The screen keyboard
automatically appears. Enter the desired value using the screen keyboard. Confirm your
input with <Enter> or cancel it with <Esc>. After the input has been confirmed or canceled,
the screen keyboard is automatically closed.

9-27
Operating a project
9.2.11.3
Keyboard control
Procedure
Enable the date/time field with one or several TAB , according to the configured tab
sequence. The selection is signaled by the colored field content.
You now have two options:
Use the cursor keys to position the cursor and then enter your value.
Press ENTER . The object changes to the specific editing mode. Now, only one character will
be marked in the field.
/
You can use the

/
The
position.
cursor keys to scroll the character table.
cursor keys can be used to move to the next or previous input
Confirm your entry with
ENTER
or cancel it with
9.2.12
User view (TP 170B and OP 170B only)
9.2.12.1
Description
ESC
Purpose
The user view is used by the administrator to manage user accounts, group assignments
and user passwords.
Users can change their passwords and logoff times.
9-28

Operating a project
Layout
The user view contains four columns for the user, password, group and log-off time. The
passwords are encrypted by means of asterisks.
The users in the "Administrators" group can view all existing users in the user view,
change all entries and create new user accounts.
Other users only see a single line in the user view showing their own user name.
If the name or password of a logged on user is entered, a system alarm is output.
Export and import

A user view contains all users, passwords, group assignments and logoff times set up on the
HMI device. To eliminate the necessity of reentering all data again on another HMI device,
you can export the user view, and then import it to another device. However, this is only
possible if this function has been configured.
Note
Do not export the password list immediately after changing it. Exit the "User view" object
after making changes and wait until the changes have been written to the internal Flash
memory before performing the export.
Notice
The currently valid passwords are overwritten during an import. The imported passwords are
valid immediately.
9.2.12.2
Touch control
Procedure
To create a new user, touch an empty line. Then use the screen keyboard to type in the user
name and confirm your entry with <Enter>. Assign a password and a logoff time in the same
way and then select the group.
To change user data, touch the relevant field and make the change.

9-29
Operating a project
9.2.12.3
Keyboard control
Procedure
Select the user view with
TAB
according to the configured tab sequence.
To create a new user, select an empty line using the cursor keys and press
Enter the user name and press
procedure.
ENTER
. Use
ENTER
to go to the next field and repeat the
To change the user data, select the desired line using the cursor keys and press
Make the desired changes and complete the action by pressing
9.2.13
Simple user view (TP 170B and OP 170B only)
9.2.13.1
Description
ENTER
ENTER
Purpose
On HMI devices with a small display, the simple user view is used to display users on the
HMI device.
Layout
Users in the "Administrators" group see all existing users in the user view.
Other users only see a single line in the user view showing their own user name.
9-30

Operating a project
9.2.13.2
Touch control
Procedure
Touch the relevant entry in the simple user view on the touch screen of the HMI device.
Use the screen keyboard to input data.
9.2.13.3
Keyboard control
Entering custom user data

Custom user data (name, password, group, logoff time) is entered sequentially in several
dialogs.
Procedure
Select the simple user view with
TAB
, using the tab order configured. Select one of the
users displayed using the cursor keys and press
ENTER
The following table shows the available key operations for entering custom user data in the
dialogs:
Key
Function
Selects the previous/next user
Selects the next element in the dialog

TAB
Opens the next dialog

ENTER

9-31
Operating a project
9-32

Operating recipes
10.1
10
Structure of a recipe
Introduction
A product often has several variants. For example, product variants can differ with respect to
size or quality. This condition is accurately reflected in a recipe.
Principle
A recipe consists of recipe data records containing values. The structure of a recipe is
explained using the example of a filing cabinet.
Each recipe represents a drawer of the file cabinet shown, and thus precisely one product. If
the fruit juice mixing plant is producing orange, apple, and tropical fruit flavors, you would
then configure one recipe for each flavor.
You define the recipe elements in the recipe. A recipe element consists of the display name
and a tag. The display names are indicated in the recipe data records and on the HMI device
in the recipe view. In Runtime, the appropriate tag value is read from the controller or
transferred to the controller.
10-1
Operating recipes
10.2 Structure of a recipe data record
10.2
Structure of a recipe data record
Introduction
A recipe data record corresponds to a file card in an individual drawer and thus to a single
product variant. If the fruit juice mixing plant is producing juice, nectar, and fruit drinks, you
would then create a recipe data record in the recipe for each product variant. In this case,
the product variants consist of the different mixing ratios for the ingrediants.
A recipe data record is a set of values for the tags defined in the recipe. You enter the values
in the input fields. You can enter the values either during configuration or during runtime on
the HMI device or the machine.
To produce a product, you transfer the appropriate recipe data record from the HMI device to
the connected controller. The values in the recipe data record cannot be changed on the
HMI device unless the configuring engineer has provided for this.
10-2

Operating recipes
10.3 Recipe in the project
Editing recipe data records

You can edit recipe data records during configuration or in runtime on the HMI device.
During configuration, you can define recipes in the "Recipes" editor in the "Elements" tab.
You can enter values in the recipe data records in the "Data records" tab.
During runtime, you have the option of entering recipe data record values directly on the
HMI device or importing them via a CSV file. You can also export the recipe data records
to a CSV file.
10.3
Recipe in the project
Overview
Recipes are a collection of associated data, e.g. machine configuration or production data.
You can transfer these data, for example, from the HMI device to the controller in a single
step in order to change the production variant. If you have programmed directly at the
machine, for example, you can transfer the data to your HMI device and write these to the
recipe.
Operating recipes in Runtime

WinCC flexible offers two options of viewing and editing recipes and the corresponding
recipe data records in Runtime on the HMI device:
Recipe views
Recipe screen

10-3
Operating recipes
10.3 Recipe in the project
Recipe views
The recipe view is a screen object that is configured in the "Screens" editor. For example,
you can specify what operating function the recipe view will have in Runtime:
The recipe view shows recipe data records in tabular form. The Recipe view is particularly
useful if data records are small in size or only a few values are to be modified.
Recipe screen
A recipe screen represents a process screen which you configured as individual input screen
form by means of an individual layout of IO fields and other screen objects in the "Screens"
editor. This makes it possible for you to input parameter data in the context of machine
visualization. The I/O fields for a recipe can be distributed over multiple recipe screens, with
topical organization of recipe elements, for example. The operating functions for the recipe
screens must be configured explicitly in the process screens.
10-4

Operating recipes
10.4 Display recipes
10.4
Display recipes
10.4.1
Display and edit recipe
Introduction
The WinCC flexible ES offers you two configuration options of viewing and editing recipes
and their corresponding data records in Runtime on the HMI device:
Recipe views
Recipe screen
Recipe views
The recipe view is a screen object that is configured in the "Screens" editor. For example,
you can specify what operating function the recipe view will have in Runtime:
The recipe view shows recipe data records in tabular form. The Recipe view is particularly
useful if data records are small in size or only a few values are to be modified.

10-5
Operating recipes
10.4 Display recipes
Simple recipe view

On HMI devices which have a display smaller than 6" (e.g. OP 77B), the simple Recipe view
is used to display and edit recipes.
The simple recipe view consists of three areas:

Recipe selection
Recipe data record selection
Recipe entries
In the simple recipe view, each area is shown separately on the HMI device. The simple
recipe view always begins with the recipe selection.
Recipe screen
A recipe screen is a process screen with a customized input screen form that you create by
setting up input/output fields and other screen objects in the "Screens" editor. This makes it
possible for you to input parameter data in the context of machine visualization. The I/O
fields for a recipe can be distributed over multiple recipe screens, which allows you a topical
organization of recipe elements. The operating functions for the recipe screens must be
configured explicitly in the process screens.
10-6

Operating recipes
10.5 Recipe view (TP 170B and OP 170B only)
10.4.2
Behavior of the recipe view
Screen change
If you change to another screen and have not yet saved changes to the recipe data in the
recipe view, you will be prompted to save the recipe data. The recipe name and the name of
the recipe record are displayed to show which recipe data have not been saved yet.
If you change to a process screen that contains a recipe view with loaded recipe data, the
recipe data will be automatically updated.
Operating the recipe view with softkeys

The Recipe view can be operated with function keys, e.g. when the HMI device does not
have touch functionality. System functions allow you to assign functions such as "Save data
record" to the function keys of the HMI device.
10.5
Recipe view (TP 170B and OP 170B only)
10.5.1
Description
Purpose
The recipe view is a screen object that is used in runtime to display and edit recipe records.
Layout
The functions of the recipe view can be configured. To use the Recipe view on small panels,
a simple view is also available, for example.
Different settings are also possible for whether the recipes available in the recipe view can
only be selected or can also be changed.
Behavior
If you change to another screen and have not yet saved changes to the recipe data in the
recipe view, you will be prompted to save the recipe data. The recipe name and the name of
the recipe record are displayed to show which recipe data have not been saved yet.
When you change to a screen that contains a recipe view loaded with recipe data, the recipe
data is automatically updated.

10-7
Operating recipes
Operator controls
The following operator controls can be configured in the recipe view:
Operator control
element
Function
Displays the configured operator notes of the given recipe view.
Creates a new recipe record in the recipe that is displayed in the specified recipe view. The recipe
record values are preset with the values that were specified as "Default value" when the recipe was
configured.
Saves the recipe data record which is currently displayed in the recipe view. The storage location is
determined during configuration in the properties view for the recipe.
Saves the recipe record currently being displayed in the recipe view under a new name. The storage
location is determined during configuration in the properties view for the recipe.
Deletes the recipe record that is displayed in the recipe view from the data medium of the HMI device.
Synchronizes the values of the recipe record that is currently displayed in the recipe view with the
associated tags.
During synchronization, all values of the recipe record are written to the associated tags. Then the
values are read from the tags and used to update the values in the recipe view.
Transfers the recipe record, which is currently displayed in the recipe view, to the connected PLC.
Transfers the recipe record, which is currently loaded in the PLC, to the HMI device and displays it in
the recipe view.
10.5.2
Touch control
Procedure
Touch the desired operating element in the Recipe view on the touchscreen of the HMI
device.
Use the screen keyboard to enter values.
10-8

Operating recipes
10.5.3
Keyboard control
Procedure
Activate the recipe view using
TAB
, according to the configured Tab order.
The table below shows the shortcut keys used to control the recipe view.
Shortcut keys
CTRL
Function
Creates a new recipe record in the recipe that is displayed in the
specified recipe view. The recipe record values are preset with the
values that were specified as "Default value" when the recipe was
configured.
CTRL
ENTER
Saves the recipe data record which is currently displayed in the recipe
view. The storage location is determined during configuration in the
properties view for the recipe.
CTRL
Saves the recipe record currently being displayed in the recipe view
under a new name. The storage location is determined during
configuration in the properties view for the recipe.
CTRL
CTRL
INS
DEL
Deletes the recipe record that is displayed in the recipe view from the
data medium of the HMI device.
Synchronizes the values of the recipe record that is currently displayed
in the recipe view with the associated tags.
During synchronization, all values of the recipe record are written to the
associated tags. Then the values are read from the tags and used to
update the values in the recipe view.
CTRL
CTRL
Transfers the recipe record, which is currently displayed in the recipe

view, to the connected PLC.
Transfers the recipe record, which is currently loaded in the PLC, to the
HMI device and displays it in the recipe view.

10-9
Operating recipes
10.6 Simple recipe view (TP 170B and OP 170B only)
10.6
Simple recipe view (TP 170B and OP 170B only)
10.6.1
Description
Purpose
On an HMI device with a small display, the simple recipe view is used to display and edit
recipes.
Layout
The simple recipe view consists of three areas:
Recipe selection
Recipe data record selection
Recipe entries
In the simple recipe view, each area is shown separately on the HMI device. The simple
recipe view always begins with the recipe selection.
Behavior
A command option selection can be called in for each display area by pressing the
button. The command selection lists those commands that are available in the current
display area. Each command is assigned a number which you can use to select it directly
from the list (without using the <Enter> key).
10-10

Operating recipes
10.6 Simple recipe view (TP 170B and OP 170B only)
Operator controls
Button
Function
Returns to the previous selection
Calls up the shortcut menu commands.
10.6.2
Touch control
Procedure
Touch the desired control object or list entry in the simple recipe view on the touch screen of
the HMI device.
10.6.3
Keyboard control
Procedure
Each command for processing recipes and recipe records is assigned a number that is
shown in the command selection. You can select the command directly by pressing the
corresponding number key on the HMI device.
The following table lists the key combinations for controlling the simple recipe view:
Shortcut keys
Function
Calls the shortcut menu commands.
Selects the previous/next entry.
+
Scrolls one page up or down and selects the corresponding entry.
HOME
END

10-11
Operating recipes
10.7 Operating recipe data record
Shortcut keys
Function
Selects the first/last entry.
SHIFT
HOME
SHIFT
END
ESC
ENTER
Returns to the previous selection

Displays the recipe data records or recipe elements according to the
selection.
10.7
Operating recipe data record
10.7.1
Recipe data record administration
Recipe data record administration

In Runtime you can, based on the configuration
Create new recipe data records
Copy recipe data records
Edit recipe data records
Delete recipe data records
That is, you can either edit recipe data records in the recipe view or screen, or import recipe
data records from a CSV file.
Creating new recipe records

1. Select the recipe on the HMI device in which you want to create a new recipe data
record.
2. Use the "Add data record" button in the recipe view or the corresponding button on the
HMI device that has this function.
A new data record with the next available number will be created. If you change the new
data record number of an existing data record number, the data record is overwritten.
3. Enter a name for the recipe data records.
4. Enter the values for the recipe data records.
The configuration data may already contain default values for the recipe data record.
5. Use the "Save" button in the recipe view or the corresponding button on the HMI device
that has this function.
10-12

Operating recipes
Result
The new recipe data records will be saved to the selected recipe. If the recipe data records
already exists, a system alarm will be output to the screen.
Copying a recipe data record

You copy a recipe record by saving it under a new name.
1. Select the recipe on the HMI device in which you want to edit an existing recipe data
record.
2. Select the recipe data record that you want to edit on the HMI device.
3. Assign a new name to the recipe data record.
As soon as you close the "Recipe data record" input field, the next free recipe data record
number will be automatically assigned to the recipe data record. You may change the
recipe data record number.
Result
The recipe data record is stored under the new name.
Modify recipe record

1. Select the recipe on the HMI device in which you want to edit an existing recipe data
record.
2. Select the recipe data record that you want to edit on the HMI device.
3. Replace the old values with new ones.
Result
The modified values are applied to the recipe data record.
Delete recipe data record

1. Select the recipe on the HMI device in which you want to delete an existing recipe data
record.
2. Select the recipe data record that you want to delete on the HMI device.
3. On the recipe view, select "Delete data record", or use the relevant HMI device button
which is assigned this function.
Result
The recipe data record is deleted from the data medium of the HMI device.

10-13
Operating recipes
10.7.2
Synchronizing a recipe data record
Introduction
In Runtime, differences between the indicated values and the actual values of the recipe
tags may arise as a result of data input in recipe views or modification of recipe tags.
Depending on the configuration, you can synchronize the values displayed in the recipe view
with the recipe tags and values of the PLC. This synchronization is performed for each one
of the recipe tags contained in the recipe data record.
Requirements
A recipe data record is displayed in the recipe view. The value of recipe tags can be
changed, for example by teach-ins.
Procedure
1. Use the "Synchronization with controller" button in the recipe view or the corresponding
button that has this function.
Result
The system always updates the current value of the recipe view with the up-to-date
recipe tag value.
When the value shown in the recipe view is more recent than the current recipe tag value,
the system writes this value to the recipe tag.
10.7.3
Read recipe data record from PLC
Introduction
You can read values from the PLC and write them to a recipe data record. For example, you
can do this in machine teach-in mode in order to save the positioning data of axes as a
recipe data record.
The read values are written to the recipe record that is currently displayed on the HMI
device.
Procedure
1. Select the recipe on the HMI device.
2. On the HMI device, select the recipe data record of which you want to fetch the values
from the PLC.
3. Use the "Read from PLC" button in the recipe view or the corresponding button on the
HMI device that has this function.
10-14

Operating recipes
Result
The values are read from the PLC, visualized on the HMI device and saved to the recipe
data record.
10.7.4
Transfer recipe record to PLC
Introduction
You can edit recipes offline or online.
Offline: The data are transferred to the PLC after the relevant command is executed.
Online: The data are transferred immediately to the PLC
In the recipe view, data are always edited offline. The configuration of the recipe screen
determines whether the recipe data are edited offline or online.
When you edit data offline, you have to transfer the changed data to the PLC.
Procedure
1. Select the recipe on the HMI device.
2. On the HMI device, select the recipe data record of which you want to transfer the values
to PLC.
3. Use the "Write to PLC" button in the recipe view or the corresponding button on the HMI
device that has this function.
Result
The values of the recipe record are transferred to the PLC.
10.7.5
Exporting and importing recipe data records
Introduction
Based on your configuration, you can either export recipe data records to a CSV file for
editing in MS Excel, for example, or import these from a CSV file. The extent to which you
can influence these processes is determined by the project configuration. Various input
boxes may be configured on the user interface:
Input of the path to the CSV file
Selection of the recipe data records for export
Overwriting an existing CSV file

10-15
Operating recipes
Export recipe data record

Requirements
Export functions are configured.
Procedure
1. Customize the export settings on the user interface of the HMI device, for example, by
setting the path to the CSV file.
2. Press the button or the key on the HMI device configured with the "Export recipe records"
function.
Result
The recipe data record are exported to a CSV file.
Note
New data records created in Runtime can be exported to an external file.
Importing recipe records

Requirements
Import functions are configured.
Procedure
1. Customize the import settings on the user interface of the HMI device, for example, by
setting the path to the CSV file.
2. Use the button or the key on the HMI device which is assigned the "Import recipe
records" function.
Result
The recipe data record are imported. If the structure of the CSV file is different from the
recipe structure, deviations are treated as follows:
Any additional values in the CSV file will be rejected.
If the CSV file contains values of the wrong data type, the configured default value is set
in the recipe record.
Example:
The CSV file contains values that show the tank contents and were input as floating point
numbers. However, the corresponding recipe tag expects an integer value. In this case,
the system discards the imported value and uses the configured default.
The system also applies the configured default value to the recipe data record if the CSV
file contains an insufficient number of values.
10-16

Maintenance/Service
11.1
11
Maintenance and service
Scope of maintenance
The HMI device is designed for maintenance-free operation. However, the touchscreen or
keyboard foil and display should be cleaned at regular intervals.
Preparation
Caution
Inadvertent operation
Only clean the HMI device after it has been switched off. This ensures that functions are not
inadvertently triggered by touching the keys or the touch screen.
Use a cloth dampened with a cleaning agent to clean the equipment. Only use water with a
little liquid soap or a screen cleaning foam as cleaning agents.
Proceed as follows
Never spray the cleaning agent directly onto the HMI device. Apply it to a cloth. Never use
aggressive solvents or scouring powder.
Caution
Do not clean the HMI device with compressed air or steam jet blowers.

11-1
Maintenance/Service
11.1 Maintenance and service
11.1.1
Clean screen
Clean screen
Only applies to HMI devices with a touchscreen.
The HMI device touchscreen can be cleaned when switched on and when operating
normally if touchscreen input has been locked by means of an appropriately configured
operator control (Clean Screen). After the Clean Screen function has been activated, all
input via the touchscreen operating elements is deactivated for a defined period of time. The
time remaining until the end of operating suppression is indicated by a progress bar.
Warning
Suppressing operating elements
During operation, clean the touchscreen only when Clean Screen is activated or switch off
the HMI device!
Pay attention to the end of operating suppression by the Clean Screen. Failure to heed this
instruction can lead to malfunction.
11.1.2
Protective foil and protective cover
Protective membrane
A protective foil is available for the touchscreens on HMI devices. The necessary ordering
information is provided in the Siemens Catalog ST 80. The protective foil is not part of the
material supplied with the HMI device.
The self-adhesive foil prevents the screen being scratched and soiled. The matte surface of
the foil reduces reflections in poor lighting conditions.
The protective foil can be removed as necessary without leaving any adhesive residue on
the screen.
Caution
Remove protective foil
Never use sharp or pointed tools, such as a knife, to remove the protective foil. This may
damage the touchscreen.
11-2

Maintenance/Service
Protective cover
The cover serves to protect the front of the TP 170micro, TP 170A and TP 170B. The cover
protects the screen and the frame of the HMI device from dirt, scratches and chemicals. This
allows the HMI devices to also be used in environments with a higher level of harmful
substances.
When the cover is used, the protective class NEMA4 is achieved.
2
3
Figure 11-1
Components of the cover
Cover frame
Protective cover
Base frame
Figure 11-2
TP 170micro, TP 170A and TP 170B with cover attached
Protective cover
Touchscreen of the HMI device
Eyelet for securing the touchscreen pen

11-3
Maintenance/Service
Requirement
The HMI device is removed.
Procedure - installation
Proceed as follows to perform the installation:
1. Place the HMI device with its front down.
Set the HMI device down in such a way that the touchscreen cannot be damaged during
the work to follow.
2. Remove installation seal on the HMI device.
Do not damage the installation seal.
Installation seal
3. Place base frame onto the HMI device.

Place the frame so that the writing field is visible.
1
2
3
2
11-4
Base frame
Recesses for the cover frame
Writing field on the base frame

Maintenance/Service
4. Insert the installation seal.
Make sure the installation seal is not twisted when inserting.
Installation seal
5. Turn the HMI device over and place it on its back.
Note
Layout of the front
In order to adapt the front of the HMI device to special requirements, a template for a
customized layout, "protective cover_Schutzhaube_TPx70_Word97-2000.doc", is
provided on the installations CD under ...\documents\
6. Put on the cover.

Check to see that the cover and the seal are completely stuck together. Use only a
faultless cover.
Protective cover
7. Place cover on the base frame and press securely.

The base frame has eight recesses. Press the base frame and cover frame together at
these points until they click into place.

11-5
Maintenance/Service
11.2 Servicing and spare parts
8. Insert the HMI device in the installation cut-out.

9. Secure the HMI device as described in these operating instructions
Procedure - dismantling
In order to remove the base frame from the cover frame, insert a suitable screwdriver into a
slit on the base frame. The cover frame can then be pried from the base frame.
11.2
Servicing and spare parts
Service pack
A service pack can be ordered for servicing purposes. It contains the following spare parts:
Installation sealing
Labeling strips: 2 sets for the OP 170B
Spring terminals: 7 pieces
Terminal block: 1 piece
The Service Pack can be ordered from your Siemens representative.
11-6

12
Specifications
12.1
Dimensioned drawings of the TP 170micro, TP 170A and TP 170B

42
6
140
156
44,5
18,1
212
5,2
21,8
196
Figure 12-1
Basic dimensions of the TP 170micro, TP 170A and TP 170B

12-1
Specifications
12.2 Dimensioned drawings of the OP 170B
12.2
Dimensioned drawings of the OP 170B

42
6
43
18,2
240
21,3
239
252
6,2
227
Figure 12-2
12.3
Overall dimensions of the OP 170B
Technical data, TP 170micro, TP 170A and TP 170B
Housing
TP 170micro
Degree of protection
Front panel
Rear panel
Weigh without packing
12-2
TP 170A
TP 170B
IP65 (NEMA 12, NEMA 4x with protective cover)

IP20
Approximately 700 g

Specifications
12.3 Technical data, TP 170micro, TP 170A and TP 170B
Display
TP 170micro
Type
TP 170micro
STN LCD
Screen area, active
116 x 87 mm (5.7")
Resolution
Colors, possible
TP 170A
320 x 240 pixels

4 Blue Mode
Back-lighting
4 Blue Mode
4 Blue Mode or
16 colors
CCFL tubes
Half Brightness Life, typical
50 000 h
Keyboard
TP 170micro
Type
TP 170A
TP 170B
Touch screen
Memory
Working memory
TP 170micro
TP 170A
256 KB
320 KB
768 KB
CF card, Type 1
TP 170micro
TP 170A
TP 170B
Memory card
TP 170B
Supply voltage
Rated voltage
24 V DC
Range, permissible
+20 %/15 %; +28.8 V to +20.4 V
Transients, maximum permissible
35 V (500 msec)
Time between two transients, minimum

Power consumption
Typical
Color
Monochrome
Constant current, maximum
Power on current surge I2t
50 s
Approx. 290 mA
Approx. 240 mA
Approx. 240 mA
Approx. 250 mA
Approx. 900 mA
Approx. 900 mA
Approx. 900 mA
A2s
A2s
Approx. 0.1 A2s
Approx. 0,2
Fuse, internal

Approx. 0,2
Electronic
12-3
Specifications
12.4 Technical data, OP 170B
12.4
Technical data, OP 170B
Housing
Degree of protection
Front panel
Rear panel
IP65
Weigh without packing
Approximately 1 kg
IP20
Display
Type
STN LCD
Screen area, active
116 87 mm
Resolution
320 240 pixels
Colors, possible
4 Blue Mode
Brightness, typical
20 cd/m2
Back-lighting
CCFL tubes
Half Brightness Life, typical
50 000 h
Keyboard
Type
Matrix membrane keyboard
System keys with dedicated functions
35, of which 3 with LED
Softkeys with configurable functions
24, of which 18 with LED
Configurable as softkeys
14
Labeling strips
8 for the keys:

F1 to F14 and K1 to K10
Memory
Working memory
768 KB
Memory card
CF card, Type 1
12-4

Specifications
12.5 Ambient conditions
Supply voltage
Rated voltage
24 V DC
Range, permissible
+20 %/15 %; +28.8 V to +20.4 V
Transients, maximum permissible
35 V (500 msec)
Time between two transients, minimum
50 s
Power consumption
Typical
Constant current, maximum
Power on current surge I2t
Approx. 250 mA
Approx. 900 mA
Approx. 0.1 A2s
Fuse, internal
12.5
Electronic
Ambient conditions
Storage and transport conditions

Table 12-1
Permissible ambient conditions
Test
Test standard
Low temperatures, high temperatures, humidity and temperature

change for storage and transport
IEC 61131, Part 2

DIN EN 60721
Cold
DIN EN 60068-2-1
Test Ab
Dry heat
DIN EN 60068-2-2
Test Bb
Temperature, alternating
DIN EN 60068-2-14
Test Nb
Moist heat, cyclic
DIN EN 60068-2-30
Test Db, Variant 2
Cold, heat, humidity and temperature change during operation
IEC 61131, Part 2

DIN EN 60721
Cold
DIN EN 60068-2-1
Test Ab
Dry heat
DIN EN 60068-2-2
Test Bb
Moist heat
DIN EN 60068-2-3
Test Ca
Temperature change, gradual

(alternative to the three mentioned above)
DIN EN 60068-2-14
Test Nb
Barometric pressure
DIN EN 60068-2-13
Barometric pressure during operation
IEC 68-2-13 (8.85)
Barometric pressure during storage
IEC 68-2-13 (8.85)
Resistance to harmful substances

Gases endangering functionality
DIN IEC 60721-3-3
12-5
Specifications
12.5 Ambient conditions
Test
Test standard
DIN IEC 60068-2-42
DIN IEC 60068-2-43
Dust endangering functionality
DIN IEC 60721-3-3
Table 12-2
Permissible mechanical ambient conditions
Test
Test standard
Vibrations
IEC 60068, Part 2-6

(sinusoidal)
Shock
IEC 60068, Part 2-29
Testing mechanical ambient conditions

The following table contains information on the type and scope of the tests relating to
mechanical ambient conditions.
Table 12-3
Testing mechanical ambient conditions
Test
Test standard
Approval values
Vibrations
IEC 60068, Part 2-6

(sinusoidal)
10 Hz f 58 Hz
constant: 0.0375 mm, constant amplitude
occasional: 0.0375 mm, constant amplitude:
58 Hz f 150 Hz
constant: 0.5 g, constant acceleration
occasional: 1 g, constant acceleration
Vibration type: Frequency cycles with a modification speed of 1 octave/min.

Vibration duration: 10 frequency cycles per axis in each of the three axes vertical to each other
Shock
IEC 60068, Part 2-29
15 g maximum value, 11 ms duration
Shock type Half-sinus

shock direction: 3 shocks in direction of axis in each of the three axes vertical to each other
Reduction of vibrations
If the HMI device will be exposed to vibration and shocks in excess of that specified in the
above table, appropriate measures must be taken to reduce the acceleration and amplitude
of the vibrations.
Use vibration absorbing materials, for example.
12-6

Specifications
12.6 EMC requirements
12.6
EMC requirements
EMC requirements
The electromagnetic compatibility (EMC) is the capacity of an electrical device to operate
satisfactorily in its electromagnetic environment without affecting the environment.
Standards
EMC requirements
EN 61000-6-4
EN 61000-6-2
Radio frequency interference
EN 55011
Interference immunity (bursts)

Interference immunity on power lines
Interference immunity on data and signal lines <30
m
Interference immunity on data and signal lines >30
m (process data lines)
Class A, Group 1
EN 61000-4-4
DC 24 V; 2.0 kV, Interference criterion
B
1,0 kV, interference criterion B
2.0 kV, interference criterion B
Interference immunity immunity (surge)
EN 61000-4-5
on DC 24500 V
1 kV symmetric
2 kV asymmetric with upstream
Dehnrail 24 FML,
Order number: 901 104
Interference immunity against static electricity (ESD)
EN 61000-4-2
8 kV with air discharge

6 kV on contact, direct/indirect
Interference criterion B
Interference immunity against radiated, radio-frequency, EN 61000-4-3

electromagnetic field
801000 MHz: 10 V/m

Modulation: 80% AM with 1 kHz
Interference criterion A
EN 61000-4-3
900 MHz, 5 MHz, 10 V/m test duration

1 Minute
Pulse modulation: 50% pulse-duty
factor 50% at 200 Hz
RF conduction on lines and line shielding
EN 61000-4-6
on DC 24 V
on signal/data lines 150 kHz to 80
MHz: 10 V/m
Modulation: 80% AM with 1 kHz
Interference immunity against magnetic fields
IEC 61000-4-8
50/60 Hz, 30 A/m effective value
Additional measures
If the HMI device is to be connected to the public power supply network, limiting Class B
must be maintained in accordance with EN 55022.

12-7
Specifications
12.7 Description of interfaces
12.7
Description of interfaces
12.7.1
Power supply
Plug connector, 2-pin
1
Figure 12-3
12.7.2
Power supply pin assignment
PIN
Allocation
+24 V DC
GND
RS 422/RS 485 (IF 1B)

Sub-D socket, 9-pin,secured by screws
5
Figure 12-4
PIN
12-8
Pin assignment of interfaces RS 485 and RS 422
Assignment with RS 422
Assignment with RS 485
n. c.
n. c.
TxD+
LTG-B
RxD+
RTS-AS
GND, potential-free
GND, potential-free
DC +5 V, potential-free
DC +5 V, potential-free
DC 24 V in
DC 24 V in
TxD
LTG-A
RxD
RTS-AS

Specifications
12.7.3
RS 232 (IF 1A)

Sub-D plug, 9-pin,secured by screws
5
Figure 12-5
Pin assignment of RS 232 interface (only applies for TP 170micro)
PIN
Allocation
12.7.4
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
n. c.
RS 232 (IF 2)
Sub-D plug, 9-pin,secured by screws
5
Figure 12-6
PIN
1
Pin assignment of RS 232 interface (only applies for TP 170micro and TP 170A)
Allocation
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
n. c.

12-9
Specifications
12-10

Appendix
A.1
Certificates and guidelines
A.1.1
Approvals
The following approvals are available for the HMI device:
Table A-1
HMI device approvals
Approvals
Standards
CE
EMC guidelines
EN 61000-6-4
EN 50082-2
EN 61000-6-2
cULus
General safety and fireproofing USA/Canada
UL 508
Environmental Rating Type 4x/12

System of protection, USA
NEMA PB 250
IP 65 Front
System of protection
EN 60529
C-Tick
EMC interference irradiation, Australia
AS/NSZ 2064
Note
The applicable approvals for the HMI device are indicated on the rear side of the device by
the corresponding symbol. The applicable approvals for the HMI device are also indicated in
the Internet at http://www.siemens.com/automation.

A-1
Appendix
A.1 Certificates and guidelines
A.1.2
ESD guidelines
What does ESD mean?

Virtually all present-day, electronic modules incorporate highly integrated MOS devices or
components. For technological reasons, these electronic components are very sensitive to
overvoltages and, consequently, to electrostatic discharge. Therefore, they are identified as
follows:
ESD Electrostatically Sensitive Devices
ESD Electrostatic Sensitive Devices
The following symbol on plates on cabinets, mounting racks or packages draws attention to
the use of ESD and, thus, to the contact sensitivity of the assemblies concerned:
Figure A-1
Symbol for ESD
ESDs may be destroyed by voltages and energies well below the perception threshold of
persons. Voltages of this kind occur as soon as a device or an assembly is touched by a
person who is not electrostatically discharged ESDs exposed to such overvoltages cannot
immediately be detected as defective in the majority of cases since faulty behavior may
occur only after a long period of operation.
Precautions against electrostatic discharge

Most plastics are capable of carrying high charges and it is therefore imperative that they be
kept away from ESDs.
When working with electrostatically sensitive components, make sure that the person, the
workstation and the packaging are properly grounded.
A-2

Appendix
A.1 Certificates and guidelines
Handling ESD assemblies

A general rule is that ESDs should be touched only when this cannot be avoided owing to
the work that has to performed on them.
Only touch devices if
you are grounded by permanently wearing an ESD wrist strap or
you are wearing ESD shoes or ESD shoe-grounding protection straps in conjunction with
an ESD floor.
Before you touch an electronic assembly, your body must be discharged. The simplest way
of doing this is to touch a conductive, grounded object immediately beforehand, e.g. bare
metal parts of a cabinet, water pipe etc.
ESDs should not be brought into contact with charge-susceptible and highly insulating
materials such as plastic films, insulating table tops and items of clothing etc. containing
synthetic fibers.
Assemblies should be deposited only on conductive surfaces, e.g. tables with an ESD
coating, conductive ESD cellular material, ESD bags, ESD shipping containers.
Do not place ESDs near visual display units, monitors or television sets (minimum distance
to screen > 10 cm).
Never touch ESDs so that contact is made with module connections or conductor rails.
Measuring ESD assemblies

Perform measurements on ESD assemblies only when
the measuring instrument is grounded, e.g. by means of a grounded conductor or
the measuring head has been briefly discharged before measurements are made with a
potential-free measuring instrument, e.g. by touching a bare metal control cabinet.
When soldering, use only grounded soldering irons.
Shipping ESD assemblies

Always store and ship ESD assemblies and devices in conductive packing, e.g. metallized
plastic boxes, metal boxes.
Packing ESD
If packing is not conductive, ESDs must be conductively wrapped before they are packed.
Use conductive foam rubber, ESD bags, domestic aluminum foil or paper, for example;
never use plastic bags or foils.
ESD with fitted battery
With assemblies containing fitted batteries, make sure that the conductive packing does
not come into contact with or short-circuit battery connectors. If necessary, cover the
connectors beforehand with suitable insulating material.

A-3
Appendix
A.2 System alarms
A.2
System alarms
Introduction
System alarms on the HMI device provide information about internal conditions of the HMI
device and controller.
The following is an overview of when system alarms occur, their causes and the remedies
available.
Note
System alarms are only displayed if an alarm window was configured. System alarms are
output in the language currently set on the HMI device.
System alarm parameters

System alarms may contain encrypted parameters which are relevant for error tracking,
because they provide a reference to the source code of the Runtime software. These
parameters are output after the text "Error code:".
Meaning of the system alarms

Number
Effect/cause
Remedy
10000
The print job cannot be started or was canceled

due to an unknown cause. The printer is not
correctly configured. Or: There is no authorization
for a network printer.
The power supply failed during data transfer.
Check the printer settings, cable connections and the

power supply.
Set up the printer once again. Obtain a network printer
authorization.
If the error persists, contact the Hotline!
10001
No printer is installed or a default printer has not

been set up.
Install a printer and/or select it as the default printer.
10002
The graphics buffer for printing is full. Up to two

images are buffered.
Allow sufficient intervals between successive print jobs.
10003
Images can now be buffered again.
10004
Overflow of the buffer for printing lines in text mode

(e.g.alarms). Up to 1000 lines are buffered.
Allow sufficient intervals between successive print jobs.
10005
Text lines can now be buffered again.
10006
The Windows printing system reports an error.

Refer to the output text and the error ID to
determine the possible causes. Nothing is printed
or the print is faulty.
Repeat the action if necessary.
20010
An error has occurred in the specified script line.

The execution of the script was therefore aborted.
Note the system alarm that may have occurred
prior to this.
Select the specified script line in the configuration.

Ensure that the tags used are of the allowed types.
Check system functions for the correct number and types
of parameters.
A-4

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
20011
An error has occurred in a script that was called by

the specified script.
The execution of the script was therefore aborted in
the called script.
Take the system event that may have occurred
prior to this into account.
In the configuration, select the script that has been called

directly or indirectly by the specified script.
Ensure that the tags used are of the allowed types.
Check the system functions for the correct number and
type of parameters.
20012
The configuration data are inconsistent. The script

could therefore not be generated.
Recompile the configuration.
20013
The scripting component of WinCC flexible Runtime Reinstall WinCC flexible Runtime.
is not correctly installed. Therefore, no scripts can
be executed.
20014
The system function returns a value that is not

written in any return tag.
Select the specified script in the configuration.

Check whether the script name has been assigned a
value.
20015
Too many successive scripts have been triggered

in short intervals. When more than 20 scripts are
queued for processing, any subsequent scripts are
rejected. In this case, the script indicated in the
alarm is not executed.
Find what is triggering the scripts. Extend the times, e.g.

the polling time of the tags which trigger the scripts.
30010
The tag could not accept the function result, e.g.

when it has exceeded the value range.
Check the tag type of the system function parameter.
30011
A system function could not be executed because

the function was assigned an invalid value or type
in the parameter.
Check the parameter value and tag type of the invalid

parameter. If a tag is used as a parameter, check its
value.
40010
The system function could not be executed since

the parameters could not be converted to a
common tag type.
Check the parameter types in the configuration.
40011
The system function could not be executed since

the parameters could not be converted to a
common tag type.
Check the parameter types in the configuration.
50000
The HMI device is receiving data faster than it is

capable of processing. Therefore, no further data
are accepted until all current data have been
processed. Data exchange then resumes.
50001
Data exchange has been resumed.
60000
This alarm is generated by the

DisplaySystemEvents function. The text to be
displayed is transferred to the function as a
parameter.
60010
The file could not be copied in the direction defined

because one of the two files is currently open or the
source/target path is not available.
It is possible that the Windows user has no access
rights to one of the two files.
Restart the system function or check the paths of the

source/target files. Using Windows NT/2000/XP: The user
executing WinCC flexible Runtime must be granted
access rights for the files.
60011
An attempt was made to copy a file to itself.

It is possible that the Windows user has no access
rights to one of the two files.
Check the path of the source/target file.

Using Windows NT/2000/XP with NTFS: The user
executing WinCC flexible Runtime must be granted
access rights for the files.

A-5
Appendix
A.2 System alarms
Number
Effect/cause
Remedy
70010
The application could not be started because it

could not be found in the path specified or there is
insufficient memory space.
Check whether the application exists in the specified path

or close other applications.
70011
The system time could not be modified.

The error message only appears in connection with
area pointer "Date/time controller". Possible
causes:
An invalid time was transferred in the job
mailbox.
The Windows user has no right to modify the
system time.
Check the time which is to be set.

Using Windows NT/2000/XP: The user executing WinCC
flexible Runtime must be granted the right to change the
system time of the operating system.
If the first parameter in the system event is

displayed with the value 13, the second parameter
indicates the byte containing the incorrect value.
70012
An error occurred when executing the function

"StopRuntime" with the option "Runtime and
operating system".
Windows and WinCC flexible Runtime are not
closed.
One possible cause is that other programs cannot
be closed.
70013
The system time could not be modified because an Check the time which is to be set.
invalid value was entered. Incorrect separators may
have been used.
70014
The system time could not be modified. Possible

causes:
an invalid time was transferred.
the Windows user has no right to modify the
system time.
Windows rejects the setting request.
Check the time which is to be set.

Using Windows NT/2000/XP: The user executing WinCC
flexible Runtime must be granted the right to change the
system time of the operating system.
70015
The system time could not be read because

Windows rejects the reading function.
70016
An attempt was made to select a screen by means

of a system function or job. This is not possible
because the screen number specified does not
exist.
Or: a screen could not be generated due to
insufficient system memory.
Check the screen number in the function or job with the

screen numbers configured.
Assign the number to a screen, if necessary.
70017
Date/Time is not read from the area pointer

because the address set in the controller is either
not available or has not been set up.
Change the address or set up the address in the

controller.
70018
Acknowledgment that the password list has been

successfully imported.
70019
Acknowledgment that the password list has been

successfully exported.
70020
Acknowledgment for activation of alarm reporting.
70021
Acknowledgment for deactivation of alarm

reporting.
70022
Acknowledgment to starting the Import Password

List action.
A-6
Close all programs currently running.

Then close Windows.

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
70023
Acknowledgment to starting the Export Password

List action.
70024
The value range of the tag has been exceeded in

the system function.
The calculation of the system function will not be
performed.
Check the desired calculation and correct it if necessary.
70025

the system function.
The calculation of the system function will not be
performed.
Check the desired calculation and correct it if necessary.
70026
No other screens are stored in the internal screen

memory.
No other screens can be selected.
70027
The backup of the RAM file system has been

started.
70028
The files from the RAM have been copied in the

Flash memory.
The files from the RAM have been copied in the
Flash memory. Following a restart, these saved
files will be copied back to the RAM file system.
70029
Backup of the RAM file system has failed.

No backup copy of the RAM file system has been
made.
Check the settings in the "Control Panel > OP" dialog and
save the RAM file system using the "Save Files" button in
the "Persistent Storage" tab.
70030
The parameters configured for the system function

are faulty.
The connection to the new controller was not
established.
Compare the parameters configured for the system

function with the parameters configured for the controllers
and correct them as necessary.
70031
The controller configured in the system function is

not an S7 controller.
The connection to the new controller was not
established.
Compare the S7 controller name parameter configured

for the system function with the parameters configured for
the controller and correct them as necessary.
70032
The object configured with this number in the tab

order is not available in the selected screen.
The screen changes but the focus is set to the first
object.
Check the number of the tab order and correct it if

necessary.
70033
An e-mail cannot be sent because a TCP/IP

Check the network connection to the SMTP server and
connection to the SMTP server no longer exists.
re-establish it if necessary.
This system event is generated only at the first
attempt. All subsequent unsuccessful attempts to
send an e-mail will no longer generate a system
event. The event is regenerated when an e-mail
has been successfully sent in the meantime.
The central e-mail component in WinCC flexible
Runtime attempts, in regular intervals (1 minute), to
establish the the connection to the SMTP server
and to send the remaining e-mails.
70034
Following a disruption, the TCP/IP connection to

the SMTP server could be re-established.
The queued e-mails are then sent.

A-7
Appendix
A.2 System alarms
Number
Effect/cause
Remedy
70035
The e-mail queue of the central component in

WinCC flexible Runtime responsible for sending emails is full. The e-mail could therefore not be
entered into the queue and therefore not sent.
The cause may be a broken connection to the
SMTP server or an overload resulting from too
much e-mail traffic.
This system event is generated only at the first
attempt. The next system event is only generated
when at least one e-mail has been successfully
sent to the queue in the meantime.
Check if
the network connection still exists or
the connection is overloaded (for example, due to
reoccurring system events resulting from disruptions).
70036
No SMTP server for sending e-mails is configured.

An attempt to connect to an SMTP server has failed
and it is not possible to send e-mails.
WinCC flexible Runtime generates the system
alarm after the first attempt to send an e-mail.
Configure an SMTP server:
70037
An e-mail cannot be sent for unknown reasons.

The contents of the e-mail are lost.
Check the e-mail parameters (recipient etc.).
70038
The SMTP server has rejected sending or

forwarding an e-mail because the domain of the
recipient is unknown to the server or because the
SMTP server requires authentication.
The contents of the e-mail are lost.
Check the domain of the recipient address or deactivate

the authentication on the SMTP server if possible. SMTP
authentication is currently not used in WinCC flexible
Runtime.
70039
The syntax of the e-mail address is incorrect or

contains illegal characters.
The contents of the e-mail are discarded.
Check the e-mail address of the recipient.
70040
The syntax of the e-mail address is incorrect or

contains illegal characters.
80001
The log specified is filled to the size defined (in

percent) and must be stored elsewhere.
Store the file or table by executing a move or copy

function.
80002
A line is missing in the specified log.
80003
The copying process for logging was not

successful.
In this case, it is advisable to check any
subsequent system events, too.
80006
Since logging is not possible, this causes a

permanent loss of the functionality.
In the case of databases, check whether the

corresponding data source exists and start up the system
again.
80009
A copying action has been completed successfully.
80010
Since the storage location was incorrectly entered

in WinCC flexible, this causes a permanent loss of
the functionality.
Configure the storage location for the respective log

again and restart the system when the full functionality is
required.
80012
Log entries are stored in a buffer. If the values are

read to the buffer faster than they can be physically
written (using a hard disk, for example),
overloading may occur and recording is then
stopped.
Archive fewer values.

Or:
Increase the logging cycle.
80013
The overload status no longer applies. Archiving

resumes the recording of all values.
A-8
In WinCC flexible Engineering System

using "Device settings > Device settings"
In the Windows CE operating system
using "Control Panel > Internet Settings > E-mail > SMTP
Server"

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
80014
The same action was triggered twice in quick

succession. Since the process is already in
operation, the action is only carried out once.
80015
This system event is used to report DOS or

database errors to the user.
80016
The logs are separated by the system function

Reconnect the logs.
"CloseAllLogs" and the incoming entries exceed the
defined buffer size.
All entries in the buffer will be deleted.
80017
The incoming entries exceed the defined buffer

size. his can be caused, for example, by several
copying actions being activated at the same time.
All copy jobs will be deleted.
Stop the copy action.
80018
All connections between WinCC flexible and the

logs have been reestablished, for example, after
executing the system function "OpenAllLogs".
Entries will be written into the logs again.
80019
All connections between WinCC flexible and all

logs have been severed, for example, after
executing the system function "CloseAllLogs".
Entries will be written to the buffer and written into
the logs when a connection is re-established.
There is no connection to the storage location and
the data medium may be being exchanged.
80020
The maximum number of simultaneously activated

copy actions has been exceeded. Copying is not
executed.
Wait until the current copying actions have been

completed and restart the last copy action.
80021
An attempt was made to delete a log which is still

involved with a copy action. Deletion has not been
executed.
Wait until the current copying actions have been

completed and restart the last action
80022
An attempt was made to start a sequence log,

which is not a sequence log, from a log using the
system function "StartSequenceLog". No sequence
log is created.
Check the project for the following:

Was the system function "StartSequenceLog"
configured correctly?
Were the tag parameters being supplied correctly on
the HMI device?
80023
An attempt was made to copy a log to itself.

The log is not copied.
Check the project for the following:

Was the system function "CopyLog" configured
correctly?
Were the tag parameters being supplied correctly on
the HMI device?
80024
The system function "CopyLog" is configured not to Modify the system function "CopyLog" in the project, if
permit copying when the target log already contains necessary. Before initiating the system function, delete
data (Parameter: "Mode"). The log is not copied.
the target log.
80025
You have interrupted the copy process.

Data written up to this point is retained. Deletion of
the target log (if configured) is not executed.
The cancellation is documented by an error entry
$RT_ERR$ at the end of the target log.

A-9
Appendix
A.2 System alarms
Number
Effect/cause
Remedy
80026
This notification is issued after all the logs have

been successfully initialized. Values are written to
the logs from this moment on. Prior to this, no
entries are written to the logs even though WinCC
flexible Runtime is running.
80027
The internal Flash memory has been specified as

the storage location for a log. This is not
permissible.
No values will be logged for this log and the log will
not be created.
Configure "Storage Card" or a network path as the

storage location.
80028
The event serves as a status acknowledgment that

initialization of the logs is currently running. No
values are logged until system event 80026 is
issued.
80029
The number of logs specified in the event could not

be initialized. Initialization of the logs has been
completed.
The faulty logs are not available for logging jobs.
Evaluate the additional system event, related to this

alarm which is also generated.
Check the configuration, the ODBC (Open Database
Connectivity) and the specified drive.
80030
The structure of existing log does not match the

expected log structure.
The logging process is stopped for this log.
Delete the existing log data manually, in advance.
80031
The log in CSV format is corrupted.

The log cannot be used.
Delete the corrupt file.
80032
Logs can be configured with events. These are

triggered as soon as the log is full. If WinCC flexible
Runtime is started and the log is already full, the
event will not be triggered.
The log specified no longer logs data because it is
full.
Stop the WinCC flexible Runtime, delete the log and

restart the WinCC flexible Runtime again.
Or:
Configure a button which contains the same actions as
the event and press it.
80033
"System Defined" is selected in the data log as the

data source name. This results in an error. No
logging is made to the database log whereas the
logging to the CSV logs works.
Install MSDE again.
80034
An error has occurred in the initialization of the

No action is necessary. However, it is recommended to
logs. An attempt has been made to create tables as save the backups or delete them to free up memory.
a backup. This did not work. A backup has been
made of the tables of the corrupt log and the log
has been newly started (empty)
80035
An error has occurred in the initialization of the

logs. An attempt has been made to create backups
of the tables and this has failed. No logging or
backup has been performed.
It is recommended to save the backups or delete them to

free up memory.
110000
The operating mode has been changed. The

operating mode is now 'offline'.
110001
The operating mode has been changed. The

operating mode is now "online".
110002
The operating mode cannot be changed.
Check the connection to the controllers.

Check whether the address area for the area pointer 88
Coordination" in the controller is available.
A-10

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
110003
The operating mode of the specified controller has

been changed by the system function
"SetConnectionMode".
The operating mode is now "offline".
110004
The operating mode of the specified controller has

been changed by the system function
"SetConnectionMode".
The operating mode is now "online".
110005
An attempt was made to use the system function

Switch the complete system to operating mode "online"
SetConnectionMode to switch the specified
and execute the system function again.
controller to the online operating mode although the
entire system is in the offline mode. This switchover is not permissible. The controller remains in
operating mode "offline".
110006
The content of the area pointer "User version" does Check:

not match the user version configured in WinCC
the user version entered on the controller
flexible. WinCC flexible Runtime is therefore
the user version entered in WinCC flexible
closed.
120000
The trend is not displayed because an incorrect

axis to the trend, or incorrect trend, has been
configured.
Change the configuration.
120001
The trend is not displayed because an incorrect

axis to the trend, or incorrect trend, has been
configured.
120002
The trend is not displayed because the tag

assigned tries to access an invalid controller
address.
Check whether the data area for the tag exists in the
controller, the configured address is correct or the value
range for the tag is correct.
130000
The action was not executed.
Close the other programs.

Delete files no longer required from the hard disk.
130001
130002
Close the other programs.

130003
No data medium is inserted. The process is

stopped.
Check, for example, if

the correct data medium is being accessed
the data medium is inserted
130004
The data medium is write-protected. The process is Check whether access has been made to the correct data
stopped.
carrier. Remove any write protection.
130005
The file is write-protected. The process is stopped.
Check whether access has been made to the correct file.

Modify the file attributes, if necessary.
130006
No access to file is possible. The process is

stopped.

the correct file is being accessed
the file exists
another action is preventing simultaneous access to
the file
130007
The network connection is interrupted.

Data records cannot be saved or read over the
network connection.
Check the network connection and correct the reason for

the disruption.
130008
The storage card is not available.

Data records cannot be saved or read to the
storage card.
Insert the storage card.

A-11
Appendix
A.2 System alarms
Number
Effect/cause
Remedy
130009
The specified directory is not on the storage card.

The files that are saved in this directory are not
saved when the HMI device is switched off.
Insert the storage card.
130010
The maximum nesting depth can be exhausted

when, for example, a value change in a script
results in the call of another script and the second
script in turn has a value change that results in the
call of another script etc.
The configured functionality is not provided.
Check the configuration.
140000
Online connection to the controller has been

successfully established.
140001
Online connection to the controller has been

disconnected.
140003
No tag updating or writing is executed.
Check the connection and whether the controller is

switched on.
Check the parameter definitions in the Control Panel
using "Set PG/PC interface".
Restart the system.
140004
No tag updating or writing is executed because the

access point or the module configuration is faulty.
Verify the connection and check whether the controller is

switched on.
Check the access point or the module configuration (MPI,
PPI, PROFIBUS) in the Control Panel with "Set PG/PC
interface".
Restart the system.
140005

address of the HMI device is incorrect (possibly too
high).
Use a different HMI device address.

Verify the connection and check whether the controller is
switched on.
Restart the system.
140006

baud rate is incorrect.
Select a different baud rate in WinCC flexible (according

to module, profile, communication peer, etc.).
140007
Tag are not updated or written because the bus

profile is incorrect (see %1).
The following parameters cannot be entered in the
registry:
1: Tslot
2: Tqui
3: Tset
4: MinTsdr
5: MaxTsdr
6: Trdy
7: Tid1
8: Tid2
9: Gap Factor
10: Retry Limit
Check the user-defined bus profile.

switched on.
Restart the system.
A-12

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
140008
No tag updating or writing is executed because

baud rate is incorrect. The following parameters
cannot be entered in the registry:
0: General error
1: Incorrect version
2: Profile cannot be entered in the registry.
3: Subnet type cannot be entered in the registry.
4: Target rotation time cannot be entered in the
registry.
5: Highest address (HSA) incorrect.

switched on.
Restart the system.
140009

module for the S7 communication was not found.
Reinstall the module in the Control Panel using "Set

PG/PC interface".
140010
No S7 communication peer could be found

because the controller is switched off.
DP/T:
The option Is not active as the only master is set
in the Control Panel under Set PG/PC interface.
Switch the controller on.

DP/T:
If only one master is connected to the network, deactivate
the option "Is not active as the only master" in "Set
PG/PC interface".
If there is more than one master connected to the
network, activate them. Do not change any settings
otherwise the bus will be disrupted.
140011

communication is interrupted.
Check the connection and that the communication peer is

switched on.
140012
There is an initialization problem (e.g. when WinCC

flexible Runtime has been terminated in the Task
Manager).
Or:
another application (e.g.STEP7) is active with
different bus parameters and the driver cannot be
started with the new bus parameters (e.g.baud
rate).
Restart the HMI device.

Or:
Start WinCC flexible Runtime first and then the other
applications.
140013
The MPI cable is not plugged in and, thus, there is

no power supply.
Check the connections.
140014
"Configured bus address already assigned."
Modify the HMI device address in the configuration in

controller.
140015
Incorrect baud rate

Or:
incorrect bus parameter (e.g.HSA)
Or:
OP address > HSA or: incorrect interrupt vector
(interrupt does not arrive at the driver)
Correct the incorrect parameters.
140016
Configured interrupt is not supported by the

hardware.
Change the interrupt number.
140017
Configured interrupt in use by another driver.
Change the interrupt number.
140018
The consistency check was deactivated by

SIMOTION Scout. Only one appropriate note
appears.
Activate the consistency check with SIMOTION Scout

again and load the configuration in the project once more.
140019
SIMOTION Scout downloads a new project to the

controller. Connection to the controller is
interrupted.
Wait until the end of the reconfiguration.

A-13
Appendix
A.2 System alarms
Number
140020
Effect/cause
Remedy
The version in the PLC and that in the configuration The following remedies are available:
(FWX file) do not match.
Download the current version to the controller using
Connection to the PLC is interrupted.
SIMOTION Scout.
Regenerate the project using WinCC flexible ES, close
WinCC flexible Runtime and restart with a new
configuration.
150000
No more data are read or written. Possible causes:

The cable is defective.
The controller does not respond, is defective,
etc.
The connection is established via the wrong
interface.
The system is overloaded.
Check that the cable is plugged in, the controller is

operational, the correct interface is being used.
Restart the system if the system event is displayed
persistently.
150001
Connection is reestablished because the cause of

the interruption has been eliminated.
160000

etc.
Connection has been established via the wrong
interface.

persistently.
160001

160010
There is no connection to the server because the

server identification (CLS-ID) cannot be
established.
Values cannot be read or written.
Check the access rights.
160011

established.

the server name is correct
the computer name is correct
the server is registered
160012

established.

the server name is correct
the computer name is correct
the server is registered
Note for experienced users:
Interpret the value from HRESULT.
160013
A-14
The specified server was started as InProc Server.

This has not been released and may possibly lead
to incorrect behavior because the server is running
in the same process area as the WinCC flexible
Runtime software.
Configure the server as OutProc Server or Local Server.

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
160014
Only one OPC server project can be started on a

Do not start a second project with OPC server
PC/MP. An error message appears when an
functionality on the computer.
attempt is made to start a second project.
The second project has no OPC server functionality
and cannot be located as an OPC server from
external sources.
170000
S7 diagnostics events are not displayed because it

is not possible to log on to the S7 diagnostics with
this unit. The service program is not supported.
170001
The S7 diagnostics buffer cannot be displayed

because communication with the controller has
been switched off.
Switch the controller online.
170002
The S7 diagnostics buffer cannot be displayed

because reading in the diagnostics buffer (SSL)
was terminated due to an error.
170003
The display of an S7 diagnostics event is not

possible. An internal error %2 has been reported.
170004
The display of an S7 diagnostics event is not

possible. An internal error with error class %2, error
number %3 has been reported.
170007
It is not possible to read in the S7 diagnostics buffer (SSL) because it was terminated with an internal
error class %2 and error code %3.
180000
A component/OCX receives configuration data with

a version identification which is not supported.
Install a newer component.
180001
The system is overloaded because too many

actions have been activated simultaneously. Not all
the actions can be executed, some are rejected.
Several remedies are available:

Increase the configured cycle times or basic clock.
Generate the alarms slower (polling).
Trigger the scripts and functions at greater intervals.
If the alarm appears more frequently:
Restart the HMI device.
180002
The on-screen keyboard could not be activated.

Possible cause:
Reinstall WinCC flexible Runtime.
The file TouchInputPC.exe was not registered due

to an incorrectly executed Setup.
190000
It is possible that the tag will not be updated.
190001
The tag is updated following an error status after

the cause of the last error state has been
eliminated (return to normal operation).
190002
The tag is not updated because communication

with the controller has been terminated.
Switch on communication via the system function

"SetOnline".
190004
The tag is not updated because the configured

address is not available for this tag.
190005
The tag is not updated because the configured

controller type does not exist for this tag.
190006
The tag is not updated because it is not possible to

map the controller type in the data type of the tag.

A-15
Appendix
A.2 System alarms
Number
Effect/cause
Remedy
190007
The tag values are not modified because the

connection to the controller has been terminated or
the tag is offline.
Switch to online mode or ! e-establish connection to the

controller.
190008
The threshold values configured for the tag have

been violated, e.g. by
an entered value
a system function
a script
Observe the configured or current threshold value of the

tag.
190009
An attempt has been made to assign a value to a

tag which is outside the value range permitted for
this data type.
E.g., a value of 260 entered for a byte tag or a
value of -3 for a word tag without a sign.
Observe the value range for the data type of the tags.
190010
The tag is described with values too often (e.g.in a

loop triggered by a script).
Values are lost because the maximum of 100
actions have been stored in the buffer.
Increase the time interval between the multi-writing tasks.
190011
Possible cause 1:
The value entered could not be written to the
configured controller tag because it was either
above or below the value range.
Make sure that the value entered is within the value

range of the controller tags.
The input is rejected and the original value is reset.

Possible cause 2:
The connection to the controller has been
terminated.
190012
It is not possible to convert a value from a source

format to a target format, e.g.:
Check the connection to the controller.

Check the value range or the data type of the tags.
An attempt is being made to assign a value to a

counter that is outside the valid, controllerdependent value range.
A tag of the type Integer should be assigned a
value of the type String.
190100
The area pointer is not updated because the

configured address for this area pointer is not
available.
Type
1 System events
2 Alarms
3 Controller acknowledgment
4 HMI device acknowledgment
5 LED mapping
6 Trend request
7 Trend transfer 1
8 Trend transfer 2
No.:
is the consecutive number displayed in WinCC
flexible ES.
190101
The area pointer is not updated because it is not

possible to map the controller type in the area
pointer type.
Parameter type and no.:
see alarm 190100
A-16

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
190102
The area pointer is updated following an error

status after the cause of the last error state has
been eliminated (return to normal operation).
Parameter type and no.: See alarm 190100.
200000
Coordination is not executed because the address

configured in the controller does not exist/has not
been set up.

controller.
200001

been written.

controller in an area which can be written.
200002
Coordination is not carried out at the moment

because the address format of the area pointer
does not match the internal storage format.
Internal error
200003
Coordination can be executed again because the

last error status has been eliminated (return to
normal operation).
200004
The coordination may not be executed.
200005

etc.
Check that the cable is plugged in and the controller is

operational.
continuously.
200100

been set up.

controller.
200101

been written.

controller in an area which can be written.
200102
Coordination is not carried out at the moment

because the address format of the area pointer
does not match the internal storage format.
Internal error
200103
Coordination can be executed again because the

normal operation).
200104
The coordination may not be executed.
200105

etc.
Check that the cable is plugged in and the controller is

operational.
continuously.
210000
Jobs are not processed because the address

been set up.

controller.
210001
Jobs are not processed because the address

configured in the controller cannot be written
to/read from.

controller in an area that can be written to/read from.
210002
Commands are not executed because the address

format of the area pointer does not match the
internal storage format.
Internal error

A-17
Appendix
A.2 System alarms
Number
Effect/cause
Remedy
210003
The job mailbox is processed again because the

normal operation).
210004
It is possible that the job mailbox is not processed.
210005
A job mailbox with an illegal number was triggered.
Check the controller program.
210006
An error occurred while attempting to execute the

job mailbox. As a result, the job mailbox will not be
executed. Observe the subsequent/previous
system event, if appropriate.
Check the parameters in the job mailbox. Recompile the

configuration.
220001
The tag is not downloaded because the associated

communication driver / HMI device does not
support downloading the data type ! oolean/bit.
220002
The tag is not downloaded because the associated

communication driver / HMI device does not
support the data type byte when writing.
220003
The communication driver cannot be loaded. The

driver may not be installed.
Install the driver by reinstalling WinCC flexible Runtime.
220004
Communication is terminated and no update is

executed because the cable is not connected or is
defective etc.
Check the connection.
220005
Communication is running.
220006
The connection is established to the specified

controller on the specified interface.
220007
The connection to the specified controller on the

specified interface is disrupted.
Check if
the cable is plugged in
the controller is OK
the correct interface is used
the configuration is OK (interface parameters, protocol
settings, controller address).
Reboot the system if the system event is displayed
persistently.
220008
The communication driver cannot access the

Close all the programs which access the interface and
specified interface or open it. It is possible that
restart the computer.
another program is using this interface or an
Use another interface available in the system.
interface is being used which is not available on the
target device.
There is no communication with the controller.
230000
The value entered could not be accepted. The

entered value is rejected and the previous value is
restored.
Either the value range has been exceeded or
impermissible characters were entered.
Enter a permissible value.
230002
Since the user currently logged on does not have

the proper authorization, the input is rejected and
the previous value is restored.
Log on as a user with sufficient rights.
230003
Changeover to the specified screen is not executed Configure the screen and check the selection function.
because the screen is not available/configured. The
current screen remains selected.
A-18

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
230005

the I/O field.
The original value of the tag is retained.
Take the value range of the tag into consideration when

entering value.
230100
During navigation in the web browser, a message

which may be of interest to the user is issued.
The web browser continues to run, but may not
(fully) display the new page but it.
Navigate to another page.
230200
The connection to the HTTP channel was

interrupted due to an error. This error is explained
by another system event.
Data are no longer exchanged.
Check the network connection.

Check the configuration of the server.
230201
The connection to HTTP channel has been

reestablished.
Data are exchanged.
230202
WININET.DLL has detected an error. This error

usually occurs when it is not possible to make a
connection to the server or the server rejects the
attempt to make a connection because the client
lacks the authorization.
An unknown server certificate can also be the
cause when the connection is encoded through
SSL.
The text of the error message provides more
information.
This text is always in the language of the Windows
installation since it originates from Windows.
Process values are no longer exchanged.
Depending on the cause:

When a connection cannot be made or a timeout occurs:
Check the network connection and the network.
Check the server address.
Check if the web server is actually running on the
target computer.
In the absence of an authorization:
Configured user name and/or password do not match
those on the server. Match them.
When the server certificate is rejected:
Certificate signed by an unknown CA ( ):
Either set the configuration to ignore this point or
install a certificate that has been signed with a root
certificate known to the client computer.
If the date of the certificate is invalid:
Install a certificate with a valid date on the server.
If there is an invalid CN (Common Name or Computer
Name):
Install a certificate with a name that corresponds to
that of the server address.
230203
Although a connection can be made to the server,

the HTTP server rejects the connection because
WinCC flexible Runtime is not running on the
server or
The HTTP channel is not supported (503
Service unavailable).
For error 503 Service unavailable: Check if:

WinCC flexible Runtime is running on the server
The HTTP channel is supported.
Other errors may occur if the web server does not

support the HTTP channel. The language of the
error text depends on the web server.
Data are not exchanged.

A-19
Appendix
A.2 System alarms
Number
Effect/cause
Remedy
230301
An internal error has occurred. An English text

explains the error somewhat more specific. One
possible cause is insufficient memory, for example.
OCX does not work.
230302
The name of the remote server cannot be

determined.
No connection can be established.
Check the configured server address.

Check if the DNS service of the network is activated.
230303
The remote server is not running on the addressed

computer.
The server address is incorrect.
Check the configured server address.

Check if the remote server is running on the target
computer.
230304
The remote server on the addressed computer is

incompatible to VNCOCX.
Use a compatible remote server.
230305
The authentication has failed because the

password is incorrect.
Configure the correct password.
230306
The connection to the remote server has been

interrupted. This may occur during network
problems.
Check if
there are network problems.
230307
The connection to the remote server was ended

because
the remote server was shut down or
the user instructed the server to close all
connections.
The connection is closed.

230308
This notification informs you about the

establishment of the connection.
A connection has just been established.
240000
WinCC flexible Runtime is operating in demo mode. Load the authorization.

You have no authorization or your authorization is
corrupt.
240001
WinCC flexible Runtime is operating in demo mode. Load an adequate authorization / powerpack.
Too many tags are configured for the installed
version.
240002
WinCC flexible Runtime is operating with a timelimited standby authorization.
Restore the full authorization.
240003
Authorization cannot be executed.

Without authorization, WinCC will run in demo
mode.
Restart WinCC flexible Runtime or reinstall it.
240004
Error while reading the standby authorization.

Restart WinCC flexible Runtime, install the authorization
WinCC flexible Runtime is operating in demo mode. or repair the authorization (see Commissioning
Instructions Software Protection).
250000
The tag in the specified line in "Status/Control" is

not updated because the address configured for
this tag is not available.
Check the set address and then check that the address
has been set up in the controller.
250001

not updated because the controller type configured
for this tag does not exist.
Check the set address.
A-20

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
250002

not updated because it is not possible to map the
controller type in the tag type.
Check the set address.
250003
No connection could be established to the

controller. The tags will not be updated.
Check the connection to the controller. Check that the

controller is switched on and is online.
260000
An unknown user or an unknown password has

been entered in the system.
The current user is logged off from the system.
Log on to the system as a user with a valid password.
260001
The logged on user does not have sufficient

authorization to perform the protected functions on
the system.
Log on to the system as a user with sufficient

authorization.
260002
This notification is triggered by the system function

"TrackUserChange".
260003
The user has logged off from the system.
260004
The user name entered into the user display

already exists in the user administration.
Select another user name because user names have to

be unique in the user administration.
260005
The entry is rejected.
Use a shorter user name.
260006
Use a shorter or longer password.
260007
The log-off time you entered is outside the valid

Enter a value between 0 and 60 minutes for the log-off
range of 0 to 60 minutes.
time.
The entered value will be discarded and the original
value is retained.
260008
An attempt was made to read a PTProRun.pwl file

created with ProTool V 6.0 in WinCC flexible.
Reading the file was interrupted due to
incompatibility of the format.
270000
A tag is not displayed in the alarm because it

attempts to access an invalid address in the
controller.
Check whether the data area for the tag in the controller
exists, whether the configured address is correct and
whether the value range for the tag is correct.
270001
There is a unit-dependent limit as to how many

alarms may be queued simultaneously in order to
be displayed (see GHB). This limit has been
exceeded.
The display no longer contains all the alarms.
However, all the alarms are recorded in the alarm
buffer.
270002
Alarms are displayed from a log, for which there is

no data in the current project.
Placeholders are issued for the alarms.
Delete older log data, if necessary.
270003
The service cannot be set up because too many

devices want to set up this service.
A maximum of four devices may execute this
action.
Connect fewer HMI devices which want to use the

service.
280000


A-21
Appendix
A.2 System alarms
Number
Effect/cause
Remedy

etc.
Connection has been established via the wrong
interface.
Check if
the correct interface is used.
280002
A connection is being used that requires a function

module in the controller.
The function block has replied. Communication can
now proceed.
280003
A connection is used that requires a function

module in the controller.
The function block has not replied.
Check if:
the correct interface is used.
280001
Reboot the system if the system event is displayed

persistently.

persistently.
Remedy depends on the error code:
1: The function block must set the COM bit in the
response container.
2: The function block must not set the ERROR bit in the
response container.
3: The function block must respond within the specified
time (timeout).
4: Establish an online connection to the controller.
280004
The connection to the controller is interrupted.

There is no data exchange at present.
Check the connection parameters in WinCC flexible.

persistently.
290000
The recipe tag could not be read or written. It is

assigned the start value.
The alarm can be entered in the alarm buffer for up
to four more failed tags, if necessary. After that, the
alarm number 290003 is issued.
Check in the configuration that the address has been set

up in the controller.
290001
An attempt has been made to assign a value to a

recipe tag which is outside the value range
permitted for this type.
to four more failed tags, if necessary. After that, the
alarm number 290004 is issued.
Observe the value range for the tag type.
290002
It is not possible to convert a value from a source

format to a target format.
to four more failed recipe tags, if necessary. After
that, the alarm number 290005 is issued.
Check the value range or type of the tag.
290003
This alarm is issued when alarm number 290000 is

triggered more than five times.
In this case, no further individual alarms are
generated.
Check in the configuration that the tag addresses have

been set up in the controller.
A-22

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
290004

generated.
Observe the value range for the tag type.
290005

generated.
Check the value range or type of the tag.
290006
The threshold values configured for the tag have

been violated by values entered.
Observe the configured or current threshold value of the

tag.
290007
There is a difference between the source and target Insert the specified data recipe tag in the source
structure of the recipe currently being processed.
structure.
The target structure contains an additional data
recipe tag which is not available in the source
structure.
The data recipe tag specified is assigned its start
value.
290008
There is a difference between the source and target Remove the specified data recipe tag in the specified
structure of the recipe currently being processed.
recipe from the project.
The source structure contains an additional data
recipe tag which is not available in the target
structure and therefore cannot be assigned.
The value is rejected.
290010
The storage location configured for the recipe is not Check the configured storage location.
permitted.
Possible causes:
Impermissible characters, write protected, data
medium full or does not exist.
290011
The data record with the specified number does not Check the source for the number (constant or tag value).
exist.
290012
The recipe with the specified number does not

exist.
Check the source for the number (constant or tag value).
290013
An attempt was made to save a data record under

a data record number which already exists.
The action is not executed.
The following remedies are available:

Check the source for the number (constant or tag
value).
First, delete the data record.
Change the "Overwrite" function parameter.
290014
The file specified to be imported could not be

found.
Check the following:

Check the file name.
Ensure that the file is in the specified directory.
290020
Acknowledgment that downloading of data records

from HMI device to controller has started.
290021

from HMI device to controller was completed
without errors.
290022

from HMI device to controller was aborted due to
an error.
Check in the configuration whether:

The tag addresses are configured in the controller
The recipe number exists
The data record number exist?
The "Overwrite" function parameter is set

A-23
Appendix
A.2 System alarms
Number
Effect/cause
Remedy
290023

from the controller to the HMI device has started.
290024
Acknowledgment that downloading data records

from the controller to the HMI device was
completed without errors.
290025

from the controller to the HMI device was aborted
due to an error.
Check in the configuration whether:

The tag addresses are configured in the controller
The recipe number exists
The data record number exist?
The "Overwrite" function parameter is set
290026
An attempt has been made to read/write a data

record although the data record is not free at
present.
This error may occur in the case of recipes for
which downloading with synchronization has been
configured.
Set the data record status to zero.
290027
No connection to the controller can be established

at present. As a result, the data record can neither
be read nor written.
Possible causes:
No physical connection to the controller (no cable
plugged in, cable is defect) or the controller is
switched off.
Check the connection to the controller.
290030
This alarm is issued after reselecting a screen that

contains a recipe display in which a data record is
already selected.
Reload the data record from the storage location or retain

the current values.
290031
While saving, it was detected that a data record

with the specified number already exists.
Overwrite the data record or cancel the action.
290032
While exporting data records it was detected that a

file with the specified name already exists.
Overwrite the file or cancel the process.
290033
Confirmation request before deleting data records.
290040
A data record error with error code %1 that cannot

be described in more detail occurred.
The action is canceled.
It is possible that the data record was not installed
correctly on the controller.
Check that the storage location, the data record, the

"Data record" area pointer and, if necessary, the
connection to the controller.
Start the action again after waiting a short period.
If the error persists, contact Customer Support. Provide
them with the error code that occurs.
290041
A data record or file cannot be saved because the

storage location is full.
Delete files no longer required.
290042
An attempt was made to execute several recipe

actions simultaneously. The last action was not
executed.
Trigger the action again after waiting a short period.
290043
Confirmation request before storing data records.
290044
The data store for the recipe has been destroyed

and will be deleted.
290050
Acknowledgment that the export of data records

has started.
290051

was completed successfully.
A-24

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
290052

was aborted due to errors.
Ensure that the structure of the data records at the

storage location and the current recipe structure on the
HMI device are identical.
290053
Acknowledgment that the import of data records

has started.
290054

was completed successfully.
290055

was aborted due to errors.
Ensure that the structure of the data records at the

storage location and the current recipe structure on the
HMI device are identical.
290056
The value in the specified line/column could not be

read/written without errors.
The action was ! ancelled.
Check the specified line/column.
290057
The tags of the recipe specified were switched from operating mode "offline" to "online".
Each modification of a tag in this recipe is now
immediately transferred to the controller.
290058
The tags of the recipe specified were switched from operating mode "online" to "offline".
Modifications to tags in this recipe are no longer
immediately transferred to the controller but must
be transferred there explicitly if necessary, by
downloading a data record.
290059
Acknowledgment that the specified data record was stored successfully.
290060
Acknowledgment that the data record memory was

cleared successfully.
290061
Acknowledgment that clearing the data record

memory was aborted due to errors.
290062
The data record number is above the maximum of

65536.
This data record cannot be created.
Select another number.
290063
This occurs with the system function

"ExportDataRecords" when the parameter
"Overwrite" is set to No.
An attempt has been made to save a recipe with a
file name that already exists.
The export is ! ancelled.
Check the system function "ExportDataRecords".
290068
Request to confirm whether all data records in the

recipe should be deleted.
290069
Request to confirm whether all data records of all

recipes should really be deleted.
290070
The data record specified is not in the import file.
Check the source of the data record number or data

record name (constant or tag value).
290071
During the editing of data record values, a value

was entered that was below the lower limit of the
recipe tag.
Enter a value within the limits of the recipe tag.

A-25
Appendix
A.2 System alarms
Number
Effect/cause
Remedy
290072
During the editing of data record values, a value

was entered that was above the upper limit of the
recipe tag.
Enter a value within the limits of the recipe tag.
290073
An action (e.g. saving a data record) was not

possible due to an unknown reason.
The error corresponds to the status alarm
IDS_OUT_CMD_EXE_ERR in the large recipe
view.
290074
While saving, it was detected that a data record

with the specified number already exists but under
another name.
Overwrite the data record, change the data record

number, or cancel the action.
290075
A data record with this name already exists.

The data record will not be saved.
Please select a different data record name.
300000
Process monitoring (e.g. using PDiag or S7-Graph) Change the controller configuration.
has been incorrectly programmed: More alarms are
queued than specified in the technical data of the
CPU. No further ALARM_S alarms can be
managed by the controller and reported to HMI
devices.
300001
The registration for ALARM_S will not be made on

this controller.
Select a controller that supports the ALARM_S service.
310000
An attempt is being made to print too many reports

simultaneously.
Since only one report can be printed at a time, the
print job is rejected.
Wait until the printout of the previous active report has

finished.
Repeat the print job if necessary.
310001
An error occurred on triggering the printer. The

report is either not printed or printed with errors.
Evaluate the additional system event, related to this

alarm which is also generated.
Repeat the print job if necessary.
320000
The movements have already been indicated by

another device.
The movements can no longer be controlled.
Select the movements on the other display units and

select the movement screen on the required display unit.
320001
The network is too complex.

The defective operands cannot be displayed.
Display the network in STL.
320002
No diagnostics-capable alarm have been selected.

The units related to the alarm could not be
selected.
Select a diagnostics-capable alarm in the screen

ZP_ALARM.
320003
No alarms exist in respect of the selected unit. No

network can be displayed in the detail view.
Select the defective unit in the general view screen.
320004
The required signal statuses could not be read by

the controller. The defective operands cannot be
determined.
Check the consistency between the configuration on the

display unit and the controller program loaded.
320005
The project contains ProAgent partitions which are

not installed. No ProAgent diagnostics can be
performed.
In order to run the project, install the ProAgent option

packet.
320006
You have attempted to execute a function that is

not possible with the current configuration.
Check the type of the selected unit.
320007
No operands causing a fault have been found in the Switch the Detail Screen to STL display mode and check
networks.
the status of the operands and exclusion operands.
ProAgent cannot display any blocked operands.
A-26

Appendix
A.2 System alarms
Number
Effect/cause
Remedy
320008
The diagnostic data saved in the configuration is

not synchronized with that in the controller.
ProAgent can only display the diagnostic units.
Recompile the project and download it to the HMI device

again.
320009
The diagnostic data saved in the configuration is

not fully synchronized with that in the controller.
The diagnostic screens can be operated normally.
ProAgent may be unable to display all diagnostic
texts.

again.
320010
The diagnostic texts saved in the configuration are

not synchronized with that in the STEP7.
The ProAgent diagnostics data are not up-to-date.

again.
320011
There is no unit with the DB number and FB

number concerned.
The function cannot be executed.
Check the parameters of function "SelectUnit" and the

units selected in the project.
320012
The "Step sequence mode" dialog box is no longer

supported.
Use Step Sequence Screen ZP_STEP from the

appropriate standard project for your project. Instead of
calling function Overview_Step_Sequence_Mode, call the
function "FixedScreenSelection" using ZP_STEP as the
screen name.
320014
The selected controller cannot be evaluated for

ProAgent.
The alarm display configured with the system
function "EvaluateAlarmDisplayFault" could not be
found.
Check the parameters of the system function

"EvaluateAlarmDisplayFault".

A-27
Appendix
A.2 System alarms
A-28

Abbreviations
CPU
Central Processing Unit
CSV
Comma Separated Values
CTS
Clear To Send
DC
Direct Current
DCD
Data Carrier Detect
DIL
Dual-in-Line (electronic chip housing design)
DP
Distributed I/Os
DSN
Data Source Name
DSR
Data Set Ready
DTR
Data Terminal Ready
EMC
Electromagnetic Compatibility
EN
European standard
ES
Engineering System
ESD
Electrostatic Discharge, the components and modules endangered by such.
ESD
Electrostatic Sensitive Device
GND
Ground
HF
High Frequency
HMI
Human Machine Interface
IEC
International Electronic Commission
IF
Interface
LED
Light Emitting Diode
MMC
Multi-Media Card
MOS
Metal Oxide Semiconductor
MPI
Multipoint Interface (SIMATIC S7)
MS
Microsoft
MTBF
Mean Time Between Failures
n. c.
Not connected
OP
Operator Panel
PC
Personal Computer
PG
Programming device
PLC
Programmable Logic Controller
PPI
Point to Point Interface (SIMATIC S7)
RAM
Random Access Memory
RTS
Request To Send
RxD
Receive Data
SELV
Safety Extra Low Voltage
SP
Service pack

B-1
Abbreviations
STN
B-2
Super Twisted Nematic
Sub-D
Subminiature D (plug)
TAB
Tabulator
TCP/IP
Transmission Control Protocol/Internet Protocol
TFT
Thin Film Transistor
TxD
Transmit Data
UL
Underwriters Laboratory

Glossary
Acknowledge
Acknowledgement of an alarm confirms that it has been noted.
AG
Is a PLC in the SIMATIC S5 series, the AG S5-115U for example
Alarm, acknowledging
Acknowledgement of an alarm confirms that it has been noted.
Alarm, arriving
Moment at which an alarm is triggered by the PLC or HMI device.
Alarm, departing
Moment at which the triggering of an alarm by the PLC is reset.
Alarm logging
Is the printout of user-defined alarms parallel to output on the HMI device screen.
Alarm, user-defined
A user defined alarm can be assigned to one of the following alarm classes:
Error
Operation
User-defined alarm classes
A user-defined alarm makes reference to a certain operating status of the system being
monitors which is connected to the HMI device via the PLC.
AS
Is a PLC in the SIMATIC S7 series, the SIMATIC S7-300 for example

C-1
Glossary
AS 511
Is the protocol of the programming unit interface to the PLC SIMATIC S5
Booting
Also refer to Starting
Bootloader
Used to start up the operating systems and is automatically started when the HMI device is
switched on. A start graphic is displayed during startup. Once the operating system is
loaded, the loader or the Control Panel is displayed, depending on the HMI device.
Bootstrapping
An option for updating the operating system. When a functional operating system is
available, updating can be carried out without booting. Otherwise, updating with booting is
necessary. In this case, the configuration computer communicates with the HMI device via
the bootloader.
Configuration computer
Is the general term for programming units and PCs on which projects are created, using a
configuration software, for use monitoring a system.
Configuration software
Is a software to create projects which serves for process visualization also refer to project,
process visualization and runtime software.
Controller
Is a general term for devices and systems with which the HMI device communicates, e.g.
SIMATIC S7.
Display duration
Defines whether and how long a system event is displayed on the HMI device.
Event
Functions are triggered by the arrival of defined events. Events can be configured. Events
which can be configured for a button include 'press button' and 'release button'.
Fault time
This relates to the time interval between the arrival and departure of an alarm.
C-2

Glossary
Field
Is an area reserved in configured screens for entering input and output values.
Flash memory
Is a memory with non-volatile memory chips which is used as a mobile storage medium in
the form of a memory card or installed permanently on the main board. The mobile storage
medium market is determined by Flash memories: CompactFlash and SmartMedia are
predominant.
CompactFlash and SmartMedia differ in their basic, inner design. In the case of CF cards,
the control electronics is in the card whereby, with SM cards, the control electronics is
installed in the associated device.
Function
A function is linked to an icon in the Control Panel or an operating element in the project.
Function key / Softkey

Is a key on the HMI device which can be configured as required. A function is assigned to
the key during the configuration. The assignment of the function keys may be dependent on
the screen being displayed or independent of the screen displayed.
Half brightness life

Time period after which the brightness of the lighting tube only achieves 50% of its original
value, for example. The specified value is dependent on the operating temperature.
Hardcopy
Represents a printout of the current screen content on a connected printer.
Image
Is a file which can be transferred from the configuration computer to the HMI device. The
Image contains the operating system for the HMI device and parts of WinCC flexible runtime
required to run a project.
IO field
The I/O field enables values to be entered or output on the HMI device which are then
transferred to the PLC.
Job mailbox
This triggers a function via the PLC.

C-3
Glossary
Notation
Is a system of characters, symbols and rules - particularly used in data processing when
defining how the programming language should be written.
Object
Is a component part of a project, e.g. a screen or alarm. Objects serve to display or enter
texts and values on the HMI device.
Operating element
Is a component part of a project to enter values and trigger functions. A button, for example,
is an operating element.
Operator note
Configurable information on objects in a project. The operator note concerning an alarm can,
for example, contain information on the cause of the fault and methods of elimination.
Process visualization
Is the representation of processes from the areas of production, logistics and services using
texts and graphics. Configured elements enable the data to be read from and written to
processes running on systems being monitored and, thus, to actively intervene in them.
Project
Is the result of a configuration using a configuration software. The project contains systemspecific objects, basic settings and alarms in the form of screens. The project is saved in the
project file with the file name extension *.hmi if it has been configured with WinCC flexible.
It is necessary to distinguish between the project on the configuration computer and that on
an HMI device. A project on the configuration computer can be available in more several
languages than can be managed on the HMI device. The project on the configuration
computer can be set up for different HMI devices. Only the project set up for a particular HMI
device can be transferred to that HMI device.
Project file
Is the compiled file which is created after the configuration from a source file for a specific
HMI device. The project file is transferred to the associated HMI device and serves for
operating and monitoring the system to be monitored. Refer to Source file.
Recipe
A combination of tags to a fixed data structure. The data structure configured can be
assigned data on the HMI device and is then referred to as a data record. The use of recipes
ensures that when a data record is downloaded, all the assigned data is transferred to the
PLC together and synchronously.
C-4

Glossary
Remote on/off
Is an option in the "Loader" menu which enables and disables remote control of the HMI
device from the PLC.
Runtime
Instantiation for a project on an HMI device. Refer to project file.
Runtime software
Is a software for process visualization with which a project on a configuration computer can
be tested also refer to project and configuration software.
Screen
A screen displays all the logically related process data on the HMI device. The display of the
process data can be supported by graphic objects.
Screen object
Is a configured object for displaying or operating the system being monitored, e.g. a
rectangle, an I/O field or Recipe View.
Source file
Is the file from which various project files can be created, depending on the configuration.
The source file is not transferred and remains on the configuration computer.
The file extension of a source file is *.hmi. Refer to Source file, compressed and Project file.
Source file, compressed

Is the compressed form of the source file. It can be transferred, in addition to the project file,
to the associated HMI device. "Enable BackTransfer" must be activated in the project on the
configuration computer. The file extension of a compressed source file is *.pdz. The standard
memory location for a compressed source file is the external memory card. Refer to Source
file.
To restore a source file, it is necessary to use the same WinCC flexible version which was
used to configure the project.
Start
A project can be called in by means of a button in the Loader. This procedure is referred to
as "starting".
STEP 7
Programming software for SIMATIC S7, SIMATIC C7 and SIMATIC WinAC.

C-5
Glossary
Symbolic IO field
Is a field for the input/output of a parameter. I.e. it contains a list of predefined entries from
which one can be selected.
System alarms
Is assigned to the "System" alarm class. A system event makes reference to internal states
in the HMI device and the PLC.
System, to be monitored
Is a general term for machines, processing centers, systems and plants as well as processes
which are to be operated and observed by an HMI device.
Tab order
Is defined during the configuration to set the sequence in which objects are focused on
pressing the <TAB> key.
Transfer
The transfer of a run-capable project to the HMI device.
Transfer mode
Is an operating mode on the HMI device used for transferring a run-capable project from the
configuration computer to the HMI device. Refer to Transfer mode.
Activates Transfer mode. Setting the HMI device to Transfer mode is a condition for
transferring data from the configuration computer to the HMI device and vice versa. A logical
connection via the data line does not exist. Refer to Transfer mode.
Tag
Is a defined memory location in which values can be written to and read from. This can be
done from the PLC or via the HMI device. Depending on whether the tags have a connection
to the PLC or not determines the difference between "external" tags (process tags) and
"internal" tags.
C-6

Index
A
Accessories
Accessory kit, 1-6
Memory card, 1-6
Accessory kit, 1-6
ACK
Key, 9-9
Acknowledge
Key, 9-9
Alarm, 1-7, 1-8
Alarm buffer
In Runtime, 8-2
Alarm indicator
Behavior, 9-19
In Runtime, 8-2
Purpose, 9-19
Alarm report, 8-2, 8-6
Alarm view
In Runtime, 8-2
Layout, 9-20
Operator controls, 9-20
Purpose, 9-20
Alarm window
In Runtime, 8-2
Alarms
In Runtime, 8-1
Alphanumeric key assignment, 9-9
Alphanumeric screen keyboard, 9-6
ALT
Key, 9-10
Ambient conditions
Ambient, 12-5
Mechanical, 12-5
application
In industrial sector, 2-1
In residential areas, 2-2
Approvals, A-1
Authorization, vi
In Runtime, 8-4
Automatic transfer, 7-6
Back transfer, 7-9

Execute, 7-10
Requirement, 7-10
Back up..., 7-12
Backspace
Key, 9-9
Backup, 6-12, 7-11, 7-12, 7-15, 7-17
Bar
Layout, 9-24
Operation, 9-24
Purpose, 9-23
Barometric pressure, 12-5
Basic dimensions of the TP 170micro, 12-1
Behavior
Alarm indicator, 9-19
IO field, 9-15
Recipe view with screen change, 10-6
Simple recipe view, 10-9
Brightness
Setting, 9-10
TP 170A, 6-4
TP 170B, 6-4
TP 170micro, 6-4
bus parameter
modify, 7-4
Button
Layout, 9-13
Purpose, 9-13
Button action feedback, 9-3

C
Cable cross-section, 4-14
Cables
Connecting, 4-5
Calculation functions, 1-7, 1-9
Calibrating
Touch screen, 6-23, 6-32
Index-1
Index
Calling
Operator note:keyboard device, 9-11
Operator note:System function, 9-7
Operator note:touch panel, 9-7
Cancel
Key, 9-9
Transfer, 6-6
Certificates
ESD, A-1
Clean screen, 11-1
Cleaning agents, 11-1
Close
Dialog, 9-11
Closing
Control Panel, 6-8
Function, 6-10
On-screen keyboard, 6-17
Combo box
open, 9-10
Communications Properties, 6-13
Compatibility conflict, 7-11
Compressing the program memory, 4-10
Configuring the interface, 4-9
Connectable controller
other manufacturers, 1-11
SIMATIC, 1-10, 1-11
Connecting
Cables, 4-5
Configuration computer, 4-11
Controller, 4-7
HMI device, 4-3
Periphery, 4-12
Plug-in terminal block, 4-14
Potential equalization line, 4-5
Power supply, 4-15
Connecting peripheral equipment
Connection configurator, 4-12
Connecting the configuration computer
Connecting the PLC
Configuring the interface, 4-9
Connecting the terminal block, 4-14
Connection
Cable cross-section, 4-14
Electrical, 4-3, 4-4
Order, 4-3
Configuration computer, 4-11
Controller, 4-7
Periphery, 4-12
Potential equalization line, 4-6
Power supply, 4-14
Index-2
Contrast
TP 170A, 6-4
TP 170B, 6-4
TP 170micro, 6-4
Control Panel
Closing, 6-8
Navigation, 6-7
open, 6-7
Control Settings
Dialog, 6-4
Controller
Number of connectable, 1-10
Number of connectible, 1-11
Copy
Recipe data record in Runtime, 10-11
create
Recipe record on the HMI device, 10-11
Cross-section
Connection cables, 4-14
CSV file, 10-2
CTRL
Key, 9-9
Cursor
Key, 9-9
D
Data loss, 5-3, 5-6, 7-17
Data record
exporting, 10-14
importing, 10-14
reading, 10-13
Transfer, 10-13
Date / time field
Behavior, 9-27
Layout, 9-26
Purpose, 9-26
Touch control, 9-27
Date and time
synchronizing, 6-14
Date/time field
Keyboard control, 9-27
Date/time properties, 6-13
Delete
Key, 9-9
deleting

Index
Dialog
Backup/Restore, 6-12
Closing, 9-11
Closing function, 6-10
Communications Properties, 6-13
Control Settings, 6-4
Date/time properties, 6-13
Keyboard properties, 6-18
Mouse properties, 6-19
OP properties, 6-21
Opening a function, 6-9
Password properties, 6-24
Printer properties, 6-26
Regional Settings properties, 6-27
S7-Transfer Settings, 6-37
Screen Saver, 6-30
Setting Ethernet transfer, 6-40
Siemens HMI Input Panel Options, 6-15
System properties, 6-31
Transfer Settings, 6-34, 6-39
DIL switch, 5-2, 5-5
Position on OP 170B, 4-9
Position on TP 170A, 4-9
Position on TP 170B, 4-9
Setting on the OP 170B, 4-10
Setting on the TP 170A, 4-10
Setting on the TP 170B, 4-10
Setting on the TP 170micro, 4-10
DirectKey, 9-3
Display, 12-2, 12-4
Setting, 6-22
Displaying
HMI device features, 6-22
E
Editing, 10-2
Recipe data record in WinCC flexible, 10-3
Recipe record, 10-2
Electrostatic charge
Precautions, A-2
EMC
Correct installation, 3-1
Guidelines, 3-1
Requirements, 12-6
Standards, 12-6
Enabling
TP 170B and OP 170B, 4-17
TP 170micro and TP 170A, 4-16
END
Key, 9-9
Enter
Key, 9-9

ENTER
Key, 9-9
ESC
Key, 9-9
ESD, A-1
Handling, A-2
Measuring, A-3
Shipping, A-3
exporting
Recipe, 10-14
Recipe record, 10-14
User data, 8-5
F
Feedback
visual, 9-3
with touch control, 9-3
File:
Saving, 6-21
Function
Additional, 1-8, 1-10
Function keys, 5-4
Labeling, 5-7
Function test, 4-18
Functional scope
TP 170B, OP 170B, 1-8
TP 170micro, TP 170A, 1-7
G
General operation
Keyboard unit, 9-8
Touch panel, 9-2
Graphic IO field
Purpose, 9-17
Group acknowledgement, 9-9
Guidelines
ESD, A-1
Index-3
Index
H
High frequency radiation, 2-1
HMI device
Connecting, 4-3
Enabling, 4-16, 4-17
Initial commissioning, 7-2
installation, 3-2
Recommissioning, 7-3
Securing, 3-3
Set parameters, 6-34
Switch off, 4-19
Transfer mode, 7-3
HMI device features
Displaying, 6-22
HOME
Key, 9-9
Housing, 12-2, 12-3
I
IF 1A, 12-8
IF 1B, 12-8
IF 2, 12-9
Image, 6-42
Version, 6-23, 7-18
Immunity to interference
EMC Guidelines, 3-1
importing
Recipe, 10-14
User data, 8-5
Initial commissioning
HMI device, 7-2
Input
Alphanumeric values, 9-6
Input of alphanumeric values, 9-6
Input panel - options, 6-15
installation
HMI device, 3-2
Installation cut-out
Dimensions, 3-5
Making, 3-5
OP 170B, 3-6
Selecting, 3-4
Space, 3-6
TP 170micro, TP 170A,TP 170B, 3-5
Installation of the HMI device
Installation position, 3-2
Type of fixation, 3-2
Installation position, 3-2
Index-4
Interfaces
OP 170B, 4-4
TP 170A, 4-4
TP 170B, 4-4
TP 170micro, 4-4
Interference immunity, 12-6
IO field
Behavior, 9-15
Keyboard control, 9-16
Layout, 9-15
Purpose, 9-15
Touch control, 9-16
K
Keyboard, 12-3, 12-4
Setting, 6-18
Keyboard control
Date/time field, 9-27
IO field, 9-16
Keyboard damage, 5-1
Keyboard layers, 9-6
Keyboard properties, 6-18
L
Labeling strips, 1-6, 5-5
Inserting, 5-8
Printing, 5-7
Template file, 5-7
Language settings, 6-4
Language switching, 9-1
Layout
Alarm view, 9-20
Bar, 9-24
Button, 9-13
IO field, 9-15
Recipe views, 10-6
Simple alarm view, 9-22
Simple user view, 9-29
Switch, 9-14
Trend view, 9-25
User view, 9-28
LED control, 8-6
Light emitting diode
Acknowledge, 9-9
Operator note, 9-9
Toggle, 9-9
List, 1-7, 1-9

Index
Load
Loader, 4-16, 4-18
Menu, 6-5
OP 170B, 6-5
TP 170A, 6-1
TP 170B, 6-5
TP 170micro, 6-1
Locking
Operating element, 11-2
Logoff time
Exporting/importing, 8-5
In Runtime, 8-5
M
Maintenance, 11-1
Making
Installation cut-out, 3-5
Manual
Range of validity, iii
Manual transfer, 7-5
Memory, 12-3, 12-4
Memory card, 1-6
Insert, 5-2, 5-6
Restoring, 7-13
Saving, 7-12
Using, 5-2, 5-6
Memory card slot, 5-5
Menu
Navigation, 6-5, 6-7, 6-10
modify
Settings in the dialog, 6-11
Mouse properties, 6-19
Moving
MPI/PROFIBUS DP address
Setting, 6-36
Multiple key operation, 9-1
N
Navigating
In Control Panel, 6-7, 6-10
in the loader, 6-5
Note
General, 2-1
Safety, 2-1
Transfer mode, 7-4
Numeric keyboard assignment, 9-9

O
Object
Alarms, 1-7, 1-8
Operator note, 1-10
Screens, 1-8
Screens, recipes, 1-9
Tags, values, lists and calculation functions, 1-7, 19
Objects in Runtime
Overview, 8-1
Offices, vi
Offline test, 7-8
Online test, 7-8
On-screen keyboard
Saving the position, 6-16
Closing, 6-17
Moving, 6-16
open, 6-15
OP 170B
Functions, 1-8
OP properties, 6-21
open
Control Panel, 6-7
Function, 6-9
Open
Combo box, 9-10
Tab, 9-11
Operating a keyboard device, 9-8
Operating element
Locking, 11-2
Operating elements and indicators
Front side, 5-1, 5-4
Operating mode
Changing, 7-3
Offline mode, 7-4
Online mode, 7-4
Transfer mode, 7-4
Operating mode switchover, 7-8
Operating recipes
Copying a recipe data record, 10-11
Creating recipe records, 10-11
Data record transfer, 10-13
Delete recipe data record, 10-12
Exporting data records, 10-14
Import a data record, 10-14
Load recipe data record, 10-11
Modify recipe record, 10-11
Read recipe data record, 10-13
Synchronizing recipe tags, 10-12
Index-5
Index
Operating system, 6-42
Configuring, 6-1, 6-5
Load, 4-16, 4-18
Updating, 7-19
Operating the touch panel (TP), 9-2
Operation
Bar, 9-24
Keyboard unit, 9-8
Touch objects, 9-2
Touch panel, 9-2
Operator controls, 5-2, 5-5
Alarm view, 9-20
DIL switch, 5-2, 5-5
Labeling strips, 5-5
Memory card slot, 5-3, 5-5, 5-6
Recipe views, 10-6
Trend view, 9-25
Operator note, 1-10
Calling:keyboard device, 9-11
Calling:system function, 9-7
Calling:Touch panel, 9-7
viewing (key), 9-9
Order
The connections, 4-3
Overall dimensions of the OP 170B, 12-2
Overall dimensions of the TP 170A, 12-1
Overall dimensions of the TP 170B, 12-1
P
Password
In Runtime, 8-5
Password properties, 6-24
PC-PPI adapter, 1-6
Pin assignment
Power supply, 12-7
RS 485, 12-8
RS-232, 12-8, 12-9
RS-422, 12-8
PLCs from other manufacturers
Reports, 1-11
Potential difference, 4-5
Potential equalization cable, 4-6
Potential equalization line
Connecting, 4-5
Potential difference, 4-5
Potential equalization cable, 4-6
Requirements, 4-5
Setting up, 4-6
Index-6
Power supply
Connecting, 4-15
Connecting the terminal block, 4-14
Reverse battery protection, 4-15
Power supply network, 12-7
Printing
Runtime, 8-6
Screen, 8-6
Project
Back transfer, 7-9
Replacing, 7-3
Stop, 9-12
Test, 7-8
Test offline, 7-8
Test online, 7-9
Transfer, 7-1
ProSave, 7-14
In WinCC flexible, 7-14
Restoring, 7-17
Saving, 7-15
Standalone, 7-14
Protective cover, 1-6, 11-2
Protective membrane, 1-6, 11-2
Purpose
Alarm indicator, 9-19
Alarm view, 9-20
Bar, 9-23
Button, 9-13
IO field, 9-15
Recipe views, 10-6
Simple user view, 9-29
Switch, 9-14
Trend view, 9-24
R
Radio frequency interference, 12-6
Recess, 3-3
Recipe, 1-9, 10-1, 10-2
Basic principles, 10-1
Data record, 10-2
Design, 10-1
Display in Runtime, 10-3, 10-4
exporting, 10-14
importing, 10-14

Index
Recipe record, 10-2
Copy, 10-11
Create on the HMI device, 10-11
deleting, 10-12
Design, 10-1
Editing in WinCC flexible, 10-3
exporting, 10-14
importing, 10-14
Load, 10-11
modify, 10-11
synchronizing, 10-12
Recipe screen, 10-5
Overview, 10-5
Recipe views, 10-4
Behavior with screen change, 10-6
Layout, 10-6
Operation with function keys, 10-6
Overview, 10-4
Purpose, 10-6
Recommissioning
HMI device, 7-3
Regional Settings properties, 6-27
Remote control
HMI device, 7-6
Setting, 6-35
Removing
Protective membrane, 11-2
Representatives, vi
Requirements
EMC, 12-6
Resistance
Harmful substances, 12-5
Restore, 6-12, 7-11, 7-12
Restore..., 7-12
Restoring
Memory card, 7-13
ProSave, 7-17
Reverse battery protection, 4-15
RF conduction, 12-7
RS 232 (IF 1A), 12-8
RS 232 (IF 2), 12-9
RS 422 (IF 1B), 12-8
RS 485 (IF 1B), 12-8
Runtime, 6-42
Language switching, 9-1
Multiple key operation, 9-1
Operation, 9-1
Pictograms, 9-2

S
S7-Transfer Settings, 6-37
Safety
In Runtime, 8-4
Safety instructions
High frequency radiation, 2-1
Work on the cabinet, 2-1
saving
Screen keyboard position, 6-16
Saving
File:, 6-21
Memory card, 7-12
ProSave, 7-15
Tab entry, 6-21
Schematic diagram
Back transfer, 7-2
Backup, 7-2
Recovery, 7-2
Transfer, 7-2
Scope of maintenance, 11-1
Screen, 1-8, 1-9
Printing, 8-6
Set brightness, 9-10
Templates, 9-2
Screen keyboard
Alphanumeric, 9-6
Screen objects
In Runtime, overview, 8-1
Screen saver, 6-30
Screen Saver, 6-30
ScreenSaver settings, 6-4
Scrolling back
Key, 9-9
Scrolling up
Key, 9-9
Securing
HMI device, 3-3
Serial transfer
Setting, 6-35
Service
In the Internet, vi
Service pack, 11-6
Servicing, 11-6
Set Baudrate, 6-36
Set region, 6-28
Set time format, 6-29
Index-7
Index
Setting
Baud rate, 6-36
Date, 6-13
Date format, 6-29
Digit separation, 6-28
Display, 6-22
Ethernet transfer, 6-40
Keyboard, 6-18
MPI/PROFIBUS DP address, 6-36
Number format, 6-28
Region, 6-28
Remote control, 6-35, 6-40
Screen saver, 6-30
Serial transfer, 6-35
Time, 6-13
Time format, 6-29
Setting digit separation, 6-28
Setting number format, 6-28
Setting remote control, 6-40
Setting the date, 6-13
Setting the date format, 6-29
Setting the time, 6-13
Settings
Brightness, 9-10
Settings in the dialog, 6-11
SHIFT
Key, 9-9
SIMATIC PLC
Profile, 1-10
Reports, 1-11
SIMATIC S5
Compressing the program memory, 4-10
Simple alarm view
Layout, 9-22
Purpose, 9-22
Simple recipe view
Behavior, 10-9
Layout, 10-8
Purpose, 10-8
Simple user view
Layout, 9-29
Purpose, 9-29
Source file
Testing, 7-10
Space
OP 170B, 3-7
TP 170B, 3-7
TP 170micro, TP 170A, 3-6
Special characters, 6-24
Spring terminal, 3-3
Standards
EMC, 12-6
Index-8
Startup screen, 4-16, 4-17

Stop
Project, 9-12
Storage conditions, 12-5
Style, 6-24
Supply voltage, 12-3, 12-4
Support
In the Internet, vi
Switch
Layout, 9-14
Purpose, 9-14
Switch off
HMI device, 4-19
Symbolic IO field
Purpose, 9-18
synchronizing, 6-14
Synchronizing
Synchronizing recipe tags, 10-12
System alarms, A-3
Meaning, A-4
Parameter, A-3
System keys, 5-4
System properties, 6-31
T
TAB
Key, 9-9
Tab entry
Saving, 6-21
Tabulator
Key, 9-9
Tag, 1-7, 1-9
Tags
in Runtime, 8-3
Technical specifications
Display, 12-2, 12-4
Housing, 12-2, 12-3
Keyboard, 12-3, 12-4
Memory, 12-3, 12-4
Power supply, 12-7
RS 485, 12-8
RS-232, 12-8, 12-9
RS-422, 12-8
Storage and transport conditions, 12-5
Supply voltage, 12-3, 12-4
Technical Support, vi, 6-23
Test
Project, 7-8
Testing
TP 170B and OP 170B, 4-17
TP 170micro and TP 170A, 4-16

Index
Toggle
Key, 9-9
Touch control
Date / time field, 9-27
IO field, 9-16
Touch objects
operating, 9-2
Touch screen
Calibrating, 6-23
Touchscreen calibration, 6-32
TP 170A
Functions, 1-7
TP 170A front view, 1-2
TP 170A side view, 1-2
TP 170B
Functions, 1-8
TP 170B front view, 1-3
TP 170B side view, 1-3
TP 170micro
Functions, 1-7
TP 170micro front view, 1-1
TP 170micro side view, 1-1
TP 170micro view from below, 1-1
Trademarks, registered, v
Training center, vi
Transfer
Cancel, 6-6
inadvertent, 7-4
Proceed as follows, 7-6
Start automatically, 7-6
Starting manually, 7-5
Transfer mode, 9-10
modify, 6-41
MPI/PROFIBUS DP, 7-5
Transfer settings, 7-5
Transfer Settings
Dialog, 6-34, 6-39
Transferring the project
Overview, 7-1
Transport conditions, 12-5
Trend view
Layout, 9-25
Purpose, 9-24
Type of fixation, 3-3
Updating
Operating system, 4-12
With booting, 7-19
Without booting, 7-19
Updating the operating system, 4-12
Upkeep, 11-1
Use
Conditions, 3-1
with additional measures, 3-1
User data
User group
In Runtime, 8-4
User view, 9-27
Export, 9-28
Import, 9-28
Layout, 9-28
Purpose, 9-27
Users
In Runtime, 8-4
V
Value, 1-7, 1-9
Version
Image, 6-23, 7-18
Version number, 7-10
Vibrations
Reduction of, 12-6
View
OP 170B front view, 1-4
OP 170B side view, 1-5
OP 170B view from below, 1-5
TP 170A front view, 1-2
TP 170A side view, 1-2
TP 170A view from below, 1-2
TP 170B front view, 1-3
TP 170B side view, 1-3
TP 170B view from below, 1-3
TP 170micro front view, 1-1
TP 170micro side view, 1-1
TP 170micro view from below, 1-1
Visual feedback, 9-3
W
U
Unplug
Memory card, 5-3, 5-6
Unplugging the memory card, 5-3, 5-6

Windows
Transfer, 4-17, 4-18
With booting
Updating, 7-19
Without booting
Updating, 7-19
Work on the cabinet, 2-1
Index-9
Index
Index-10


XP170X

Uploaded by

Copyright:

Available Formats

XP170X

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

XP170X

Uploaded by

Copyright:

Available Formats

Preface

Order number 6AV6691-1DB01-0AB0

Safety instructions and

Installation and connection

Operator control elements

Operating system and

Preparing and backing up a

Copyright Siemens AG, 2004. All rights reserved

Basic knowledge required

Scope of the manual

TP 170micro, TP 170A, TP 170B, OP 170B (WinCC flexible)

Placement in the information landscape

TP 170micro, TP 170A, TP 170B, OP 170B (WinCC flexible)

Terminology that occurs in the user interface, e.g., dialog

"File > Edit"

Operational sequences, e.g., menu commands/shortcut menu

Please observe notes labeled as follows:

TP 170micro, TP 170A, TP 170B, OP 170B (WinCC flexible)

Representatives and offices

Service & support in the Internet

TP 170micro, TP 170A, TP 170B, OP 170B (WinCC flexible)

A&D Technical Support and Authorization

America (Johnson City)

Technical Support and Authorization

Technical Support and Authorization

Information is available in German and English.

TP 170micro, TP 170A, TP 170B, OP 170B (WinCC flexible)

TP 170micro, TP 170A, TP 170B, OP 170B (WinCC flexible)

Design of the TP 170micro HMI device ..................................................................................... 1-1

Design of the TP 170A HMI device............................................................................................ 1-2

Design of the TP 170B HMI device............................................................................................ 1-3

Design of the OP 170B HMI device ........................................................................................... 1-4

Miscellaneous ............................................................................................................................ 1-6

Functional scope of WinCC flexible on TP 170micro and TP 170A .......................................... 1-7

Functional scope of WinCC flexible on TP 170B and OP 170B ................................................ 1-9

Communication using TP 170micro ......................................................................................... 1-11

Communication using the TP 170A, TP 170B and OP 170B .................................................. 1-11

Safety instructions and general notes ..................................................................................................... 2-1

Safety instructions...................................................................................................................... 2-1

General notes............................................................................................................................. 2-2

Planning use........................................................................................................................................... 3-1

Installation notes ........................................................................................................................ 3-1

Installation position and fixation ................................................................................................. 3-2

Installation cut-out...................................................................................................................... 3-4

Installation and connection ..................................................................................................................... 4-1

Checking the shipment .............................................................................................................. 4-1

Installation of the HMI device..................................................................................................... 4-1

Connecting the HMI device........................................................................................................ 4-3

TP 170micro, TP 170A, TP 170B, OP 170B (WinCC flexible)

Operator control elements and displays.................................................................................................. 5-1

Other operator controls on the TP 170A and TP 170B.............................................................. 5-2

Other operating elements on the OP 170B................................................................................ 5-5

Operating system and configuration ....................................................................................................... 6-1

Configuring the TP 170micro and TP 170A operating system................................................... 6-1

Touchscreen calibration ........................................................................................................... 6-35

Configuring transfer mode for the TP 170A ............................................................................. 6-37

Runtime .................................................................................................................................... 6-45

Preparing and backing up a project ........................................................................................................ 7-1

Transferring a project to an HMI device..................................................................................... 7-1

Transfer ...................................................................................................................................... 7-4