Meet with mega satisfaction

SPECIFICATION FOR APPROVAL

Part No. M IP260B-1
Description: LCD Power Supply And Inverter (2 In 1)Specification
Revision: 1.3
Customer.
Customer Approval No. :



Please return to us one original of SPECIFICATION FOR APPROVAL with your approved signatures.


APPROVED SIGNATURES

APPROVED BY DATE

CHOP & SIGNATURES:


SHENZHEN MEGMEET ELECTRICAL TECHNOLOGY CO.,LTD
Add: 6F Tower 2, Zhongjian Industrial Building
18 Yanshan Road , Shekou, Shenzhen, P.R.China
ZIP CODE:518067
TEL: (0755)26693042 26693442
FAX: (0755)26693047
MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
1 OF 12
E-mail [email protected]:

Spec.
Rev.
Sample
Rev.
Date Description Safety
by
Mechanical
by
Electrical
by
1.1 1.1 07.06.28
1.2 1.2 07.11.10 1.1,1.4.2,1.5.1,8.1
,9

1.3 1.3 08.05.29 1.2.1
















MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
2 OF 12


MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
3 OF 12
Section
1. Power supply overview
1.1 Input Electrical Characteristics Overview
1.2 Output Electrical Characteristics Overview
1.2.1 Output Voltage ,Current & Regulation.
1.2.2 DC Output Ripple & Noise.
1.2.3 Output Transient Response.
1.2.4 DC Output Hold-Up Time.
1.2.4 DC Output Overshoot At Turn On & Turn Off.
1.2.6 DC output voltage rise time
1.3 Remote On/Off Control
1.4 Protection:
1.4.1 DC output Over Voltage Protection.
1.4.2 DC Output Over current Protection.
1.4.3 DC Output Short Circuit Protection.
1.4.4 Over Temperature Protection.
1.4.5 Reset After Shutdown.
1.5 Inverter Specification
1.5.1 Spec.
1.5.2 Sequence
2. Isolation
3. Safety
4. EMC
4.1 EMI
4.2 EMS
5. Environmental Requirement
5.1 Temperature
5.2 Humidity
5.3 Altitude
5.4 Cooling Method
5.5 Vibration
5.6 Impact
6. Dimension
7. Weight
8. Pin Connection ()
9. Power Supply mounting
10. Package ()





MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
4 OF 12
1. Power Supply Overview :
1.1 Table 1 Input Electrical Characteristics Overview
Input voltage range 90Vac to 264Vac
Normal voltage range 100Vac to 240Vac
Frequency range 50Hz/60Hz
Max input ac current

1.8Amax at full load condition
Inrush current (cold start)

50Atyp peak, 120Vac; 100Atyp peak, 220Vac
Efficiency(full load) 80%min at 90Vac
Harmonic current Meet GB17625.1-1998/IEC61000-3-2 class D
Leakage Current Less Than 0.7mA, 240Vac input(class )
Standby Power Loss 1W @240Vac input ,output 30mA

1.2 Output Electrical Characteristics Overview
1.2.1 Table 2 Output Voltage ,Current & Regulation.
Output Voltage

Regulation

Min. current

Rated current

Peak current

+12V 10.8V-13.2V 0.1A 3A* 4A**
+5V 5.05V-5.45V 0.05A 3.5A*
+VS 5.05V-5.45V 0.02A 2A*
4A**
Note:*total output power100w,+5V and +VS Output current 4A(BK action).
* *pulse width within 100ms 100
1.2.2 Table 3 DC Output Ripple & Noise.
Output Voltage Ripple & Noise (Max.)
+12V 700mVp-p-typ@25;
+5V 100mVp-p@25; Io 0.5A
+VS 150mVp-p@25; Io 0.5A
Note: 1) Measurements shall be made with an oscilloscope with 20MHz bandwidth.
20
2) Outputs shall be bypassed at the connector with a 0.1uF ceramic capacitor and a
10uF electrolytic capacitor to simulate system loading.
0.1uF 10uF



MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
5 OF 12
1.2.3 Output Transient Response.
Table 4. Test condition.
Voltage Tolerance Limit Slew Rate Load Change
+5V,+VS 5V-5.5V 0.2A/uS 50% to Max load
+12V 10.8V-13.2V 0.2A/uS 50% to Max load
Note: Transient response measurements shall be made with a load changing repetition
rate of 50Hz to 1kHz. 50~1KHz

1.2.4 Table 5 DC Output Hold-Up Time.
Output Voltage 110Vac input 220Vac input
+12V 10 mStyp 10 mStyp
+5V 20 mS 20 mS
+VS 20 mS 20 mS
Note: All of dc output at full load.

1.2.5 Table 6 DC Output Overshoot At Turn On & Turn Off.
Over shoot voltage(V) Output(V)
Turn on Turn off
+12V 10% 10%
+5V 5% 5%
+VS 5% 5%
Note: All of dc output current from Min. to Max.

1.2.6 Table 7 DC output voltage rise time
Output Voltage 110Vac input &Full Load 230Vac input &Full Load
+12V 30 mS 30 mS
+5V 30 mS 30 mS
+VS 30 mS 30 mS
Note: The output voltages shall rise from10% to 90% of their output voltage.
10%90%
1.3 Remote On/Off Control
The power supply DC outputs shall be enable with an active-high TTL(
2.5V/2.0mA)-compatible signal(SB). The +VS is on whenever the AC power is present.
+VS TTL SB2.5V/2.0mA,
+VS

MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
6 OF 12
* When SB is pulled to high, the 5V and 12V outputs are to be enabled.
SB 5V 12V
* When SB is pulled to TTL low or open circuit, the DC outputs are to be disabled.
SB
* CCFL-VOL. Output shall be enable with BK signal ( 4.5V-5.5V).
* BK
Table 8.
Ps-on Signal Comments Outputs
SB- high 2.5V&2.0mA ( source) Output
SB- low 0.8V X
SB-open -- X

1.4 Protection:
1.4.1 Table 9 DC output Over Voltage Protection.
Output Voltage Max. Over Voltage Comments
+12V 15Vtyp Power supply latch into shutdown state

+5V 7Vtyp --
+VS 7Vtyp --
Note: The power supply shall be test at max AC voltage (270Vac) and min load or no load.
270
1.4.2 Table 10 DC Output Over current Protection.
Output Voltage Over Current Comments
+5V 4A Hiccup
+VS 4A Hiccup
Note: +VS and +5V total output current4A.

1.4.3 Table 11 DC Output Short Circuit Protection.
Output Voltage Comments
+12V Shutdown
+5V Hiccup
+VS Hiccup

1.4.4 Reset After Shutdown.

MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
7 OF 12
1. Recycle the SB signal or restart AC input, the power supply will restart after the fault
removed.
SB
1.5 Inverter Electrical Specification
1.5.1 Table 1
Parameter Symbol Min. Max. Note
Backlight Control Section
Backlight On 2.5V 5.5V
Backlight Off
BK
0V 0.8V
Lamp Operating Section
Lamp Frequency FL 45KHz 75KHz
Lamp RMS current IL 7.0mA 8.0mA
Lamp Operating Voltage Vw 1920Vrms typ
3180Vrms 3800Vrms Ta=0 Lamp Starting Voltage Vs
-- --
Protection Section
Lamp OCP IM 10mA 14mA
CCFL-Vol. Short -- -- -- yes

Note: Ta=25,And after 30 minutes warm up unless otherwise specified.
1.5.2 Timing Seqence ()
2. Isolation
2.1 Table 12
Input To Output DC500V 50Mmin (at room temperature)
Input To FG DC500V 50Mmin (at room temperature)
Output To FG Non Isolated
Note:

2.2 Table 13
Input To Output 3000Vac 50Hz 1minute 10mA
Input To GND 1500Vac 50Hz 1minute 10mA
Note:


MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
8 OF 12
3. Safety
The power supply shall compliance with the following Criterion:

1) UL60065
2) EN60065
3) GB8898

4. EMC
4.1 EMI
The power supply shall compliance with the following Criterion:

1) Conduction Emission :
*EN55022, CLASS B
*GB9254, CLASS B
*FCC PART15 CLASS B
2) Radiated Emission :
*EN55022, CLASS B
*GB9254, CLASS B
*FCC PART15 CLASS B


4.2 EMS
The power supply shall compliance with the following Criterion:

1) ESD
*GB17626.2-1998/IEC61000-4-2
2) EFT
*GB17626.4-1998/IEC61000-4-4 3KV
3) Surge
*GB17626.5-1998/IEC61000-4-5 1.5KV / 3KV

5. Environmental Requirement
5.1 Temperature
* Operating: 0 to +50.
* Store: -20 to +80.

MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
9 OF 12
5.2 Humidity
* Operating: From 10%to90% relative humidity (non-condensing).
* Store: From 5 to 95% relative humidity (non-condensing).
5.3 Altitude
* Operating: to10,000 ft.
* Store: to 20,000ft.
5.4 Cooling Method
* Ventilation cooling .
5.5 Vibration
* 10-55Hz, 19.6m/s(2G), 3minutes period, 60minutes each along X, Y and Z axis.
5.6 Impact
* 49m/s(5G),11ms, once each X, Y and Z axis.
6. Dimension
* 300mm X 115mm X 21mm (L *W * H ).
7. Weight
400g
8. Pin Connection ()
Table 15 Pin-CN3 Connection And Function
NO. Pin Connection Function
1 +5VSB STANDBY OUTPUT
2.3 +12V +12V OUTPUT
4.5 GND GND RETURN
6.7 5V +5V OUTPUT
8.9 GND GND RETURN
10 SB SMPS ON/OFF CONTROL(ON = HIGH)
11 BK BACKLIGHT ON
12 DM INTERNAL PWM DIMMING
Note: CN3 -- J ST VA CONNEETION, TYPE : pitch2.5mm









MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
10 OF 12
Table 16 Pin-CN10 Connection And Function
NO. Pin Connection Function
1 GND +5V RETURN
2 GND +5V RETURN
3.4.7.8 +5V +5V OUTPUT
5 SB SMPS ON/OFF CONTROL(ON = HIGH)
6 +VS STANDBY OUTPUT
9.10.11 GND +VS. +12V RETURN
12.13 +12V +12V OUTPUT
Note: CN10 -- J ST VA CONNEETION, TYPE : pitch2.5mm

Table 17 Pin-CN11 Connection And Function
NO. Pin Connection Function
1 GD GND
2 SB SMPS ON/OFF CONTROL(ON = HIGH)
3 DM INTERNAL PWM DIMMING
4 BK BACKLIGHT ON
5 PM EXTERNAL PWM DIMMING DUTY
Note: CN11 -- J ST VA CONNEETION, TYPE : pitch2.0mm
Table 18 Pin-CN4CN5CN6CN7 Connection And Function
NO. Pin Connection Function
12 CCFL CCFL-VOL. Output
Note:
Table 19 Pin-CN2 Connection And Function
NO. Pin Connection Function
1 AC-N2OO9 AC INPUT NUTURE FROM SW
2 NC NC
3 AC-L2 AC INPUT LINE FROM SW
4 NC NC
5 AC- N1 AC INPUT LINE TO SW
6 NC NC
7 AC- L1 AC INPUT NUTURE TO SW
Note: CN2 -- J ST VA CONNEETION, TYPE : pitch3.96mm


Table 20 Pin-CN1 Connection And Function
NO. Pin Connection Function
AC-N AC INPUT NUTURE
NC NC
AC-L AC INPUT LINE
Note: CN1 -- J ST VA CONNEETION, TYPE : pitch3.96mm

Table 21 Pin-CN8 Connection And Function
Pin Connection Function
PIN AND PIN SHORT EXTERNAL PWM DIMMING DUTY ENABLE
PINAND PIN OPEN INTERNAL PWM DIMMING
Note: CN8 -- J ST VA CONNEETION, TYPE : pitch2.54mm

Fig.8.1 Pin Connection (Top View)





MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
11 OF 12


9. Power Supply Mounting
:Fig.8.1
Mount Method( )
,,












10. Package


MEGMEET
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
()
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MIP260B-1
DATE PREPARED CHECKED APPROVED
REV:
2008/05/29
ZUZHILI GUICHENGCAI
ZHANGZHI
Document No.:
MSPS-MIP260B-1
1.3
12 OF 12