17

Refrigeration Cycle
UNIT 2 REFRIGERATION CYCLE
Structure
2.1 Introduction
Objectives
2.2 Vapour Compression Cycle
2.2.1 Simple Vapour Compression Refrigeration Cycle
2.2.2 Theoretical Vapour Compression Cycle with Saturated Vapour after Compression
2.2.2 Conditions for Highest COP
2.2.3 Carnot Refrigeration Cycle
2.2.4 Temperature Limitations
2.2.5 Difference between Refrigeration and Heat Pump Cycles
2.3 Vapour Absorption System
2.4 Illustrative Problems
2.5 Summary
2.6 Answers to SAQs
2.1 INTRODUCTION
The term refrigeration may be defined as the process of removing heat from a
substance under controlled conditions. It also includes the process of reducing and
maintaining the temperature of a body below the general temperature of its surroundings.
In other words, the refrigeration means a continued extraction of heat from a body whose
temperature is already below temperature of its surroundings. In a refrigerator, heat is
virtually pumped from a lower temperature to a higher temperature. According to Second
Law of Thermodynamics, this process can only be performed with the aid of some
external work. It is thus obvious that supply of power is regularly required to drive a
refrigerator. Theoretically, a refrigerator is a reversed heat engine or a heat pump which
pumps heat from a cold body and delivers it to a hot body. The substance which works in
a pump to extract heat from a cold body and to deliver it to a hot body is known as
refrigerant.
Objectives
After studying this unit, you should be able to
- know what is refrigeration cycle,
- understand about the vapour compression cycle,
- describe the vapour compression refrigeration cycle, and
- solve the problem on refrigeration system.
Refrigeration cycle is the basis of all refrigeration systems. So refrigeration cycle should
be known to understand the refrigeration system. Some basic refrigeration cycles are
discussed here through different diagrams.
2.2 VAPOUR COMPRESSION CYCLE
Vapour compression cycle is an improved type of air refrigeration cycle in which a
suitable working substance, termed as refrigerant, is used. The refrigerants generally used
for this purpose are ammonia (NH
3
), carbon dioxide (CO
2
) and sulphur-dioxide (SO
2
).
The refrigerant used, does not leave the system, but is circulated throughout the system
alternately condensing and evaporating. In evaporating, the refrigerant absorbs its latent
heat from the solution which is used for circulating it around the cold chamber and in
condensing; it gives out its latent heat to the circulating water of the cooler.

18
Refrigeration and Air
Conditioning
The vapour compression cycle which is used in vapour compression refrigeration system
is now-a-days used for all purpose refrigeration. It is used for all industrial purposes from
a small domestic refrigerator to a big air conditioning plant.
2.2.1 Simple Vapour Compression Refrigeration System
It consists of the following essential parts:
Compressor
The low pressure and temperature vapour refrigerant from evaporator is drawn into
the compressor through the inlet or suction valve A, where it is compressed to a
high pressure and temperature. This high pressure and temperature vapour
refrigerant is discharged into the condenser through the delivery or discharge
valve B.
Condenser
The condenser or cooler consists of coils of pipe in which the high pressure and
temperature vapour refrigerant is cooled and condensed.

Figure 2.1 : Simple Vapour Compression Refrigeration System
The refrigerant, while passing through the condenser, gives up its latent heat to the
surrounding condensing medium which is normally air or water.
Receiver
The condensed liquid refrigerant from the condenser is stored in a vessel known as
receiver from where it is supplied to the evaporator through the expansion valve or
refrigerant control valve.
Expansion Valve
It is also called throttle valve or refrigerant control valve. The function of the
expansion valve is to allow the liquid refrigerant under high pressure and
temperature to pass at a controlled rate after reducing its pressure and temperature.
Some of the liquid refrigerant evaporates as it passes through the expansion valve,
but the greater portion is vaporized in the evaporator at the low pressure and
temperature
Evaporator
An evaporator consists of coils of pipe in which the liquid-vapour. refrigerant at
low pressure and temperature is evaporated and changed into vapour refrigerant at
low pressure and temperature. In evaporating, the liquid vapour refrigerant absorbs
its latent heat of vaporization from the medium (air, water or brine) which is to be
cooled.

19
Refrigeration Cycle 2.2.2 Theoretical Vapour Compression Cycle with Dry Saturated
Vapour after Compression
A vapour compression cycle with dry saturated vapour after compression is shown on T-s
diagrams in Figures 2.2(a) and (b) respectively. At point 1, let T
1
, p
1
and s
1
be the
temperature, pressure and entropy of the vapour refrigerant respectively. The four
processes of the cycle are as follows :

(a) T-s Diagram (b) p-h Diagram
Figure 2.2 : Theoretical vapour Compression Cycle
with Dry Saturated Vapour after Compression
Compression Process
The vapour refrigerant at low pressure p
1
and temperatureT
1
is compressed
isentropically to dry saturated vapour as shown by the vertical line 1-2 on the T-s
diagram and by the curve 1-2 on p-h diagram. The pressure and temperature rise
from p
1
to p
2
and T
1
to T
2
respectively.
The work done during isentropic compression per kg of refrigerant is given by
w = h
2
h
1

where h
1
= Enthalpy of vapour refrigerant at temperature T
1
, i.e. at suction of the
compressor, and
h
2
= Enthalpy of the vapour refrigerant at temperature T
2
. i.e. at discharge
of the compressor.
Condensing Process
The high pressure and temperature vapour refrigerant from the compressor is
passed through the condenser where it is completely condensed at constant
pressure p
2
and temperature T
2
as shown by the horizontal line 2-3 on T-s and p-h
diagrams. The vapour refrigerant is changed into liquid refrigerant. The refrigerant,
while passing through the condenser, gives its latent heat to the surrounding
condensing medium.
Expansion Process
The liquid refrigerant at pressure p
3
= p
2
and temperature T
3
= T
2
, is expanded by
throttling process through the expansion valve to a low pressure p
4
= p
1
and
Temperature T
4
= T
1
as shown by the curve 3-4 on T-s diagram and by the vertical
line 3-4 on p-h diagram. Some of the liquid refrigerant evaporates as it passes
through the expansion valve, but the greater portion is vaporized in the evaporator.
We know that during the throttling process, no heat is absorbed or rejected by the
liquid refrigerant.
Vaporizing Process
The liquid-vapour mixture of the refrigerant at pressure p
4
= p
1
and temperature
T
4
= T
1
is evaporated and changed into vapour refrigerant at constant pressure and
temperature, as shown by the horizontal line 4-1 on T-s and p-h diagrams. During
evaporation, the liquid-vapour refrigerant absorbs its latent heat of vaporization

20
Refrigeration and Air
Conditioning
from the medium (air, water or brine) which, is to be cooled, This heat which is
absorbed by the refrigerant is called refrigerating effect and it is briefly written as
R
E
. The process of vaporization continues up to point 1 which is the starting point
and thus the cycle is completed.
We know that the refrigerating effect or the heat absorbed or extracted by the
liquid-vapour refrigerant during evaporation per kg of refrigerant is given by
R
E
= h
1
h
4
= h
1
hf
3

where hf
3
= Sensible heat at temperature T
3
, i.e. enthalpy of liquid refrigerant
leaving the condenser.
It may be noticed from the cycle that the liquid-vapour refrigerant has extracted
heat during evaporation and the work will be done by the compressor for isentropic
compression of the high pressure and temperature vapour refrigerant.
Coefficient of performance, C.O.P. = (Refrigerating effect)/( Work done)
=
1 4
2 1
h h
h h

=
1 3
2 1
f
h h
h h

Effect of Suction Pressure
The suction pressure (or evaporator pressure) decreases due to the frictional
resistance of flow of the refrigerant. Let us consider a theoretical vapour
compression cycle 1-2-3-4 when the suction pressure decreases from p
s
to p
s'
as
shown on p-h diagram in Figure 2.3.
It may be noted that the decrease in suction pressure :
(a) decreases the refrigerating effect from (h
1
h
4
) to (
1
4
1
1
h h ), and
(b) Increases the work required for compression from (h
2
h
1
) to
(
1 1
2 1
h h ).

Figure 2.3 : Effect of Suction Pressure
Since the C.O.P, of the system is the ratio of refrigerating effect to the work done,
therefore with the decrease in suction pressure, the net effect is to decrease the
C.O.P. of the refrigerating system for the same refrigerant flow. Hence with the
decrease in suction pressure the refrigerating capacity of the system decreases and
the refrigeration cost increases.
Effect of Discharge Pressure
In actual practice, the discharge pressure (or condenser pressure) increases due to
frictional resistance of flow of the refrigerant. Let us consider a theoretical vapour
compression cycle l-2-3-4 when the discharge pressure increases from p
D
to p
D
as
shown on p-h diagram in Figure 2.4 resulting in increased compressor work and
reduced refrigeration effect.

21
Refrigeration Cycle








Figure 2.4 : Effect of Discharge Pressure
2.2.3 Conditions for Highest COP
Effect of Evaporator Pressure
Consider a simple saturation cycle 1-2-3-4 with Freon 12 as the refrigerant as
shown in Figure 2.5 for operating conditions of t
k
= 40C and t = 5C.
Now consider a change in the evaporator pressure corresponding to a decrease in
the evaporator temperature to 10C. The changed cycle is shown as 1'-2'-3-4' in
Figure 2.5.
It is therefore, seen that a drop in evaporator pressure corresponding to a drop of
5C in saturated suction temperature increases the volume of suction vapour and
hence decreases the capacity of a reciprocating compressor and increases the
power consumption per unit refrigeration.

Figure 2.5 : Effect of Evaporator Pressure
It is observed that a decrease in evaporator temperature results in :
(a) Decrease in refrigerating effect from (h
1
h
4
) to (h
1
'

h
4
')
(b) Increase in the specific volume of suction vapour from v
1
to v
1
'

(c) Decrease in volumetric efficiency, due to increase in the pressure
ratio, from
v
q to
' v
q
(d) Increase in compressor work from (h
2
h
1
) to (h
2
'

h
1
') due to
increase in the pressure ratio as well as change from steeper isentropic
1-2 to flatter isentropic 1'-2.
Since
0
1
0 0
q
v
V
mq Q
p v
q
= = . . . (2.1)
and w m W
* *
= . . . (2.2)

22
Refrigeration and Air
Conditioning
Expressions for the dependence of capacity and unit power consumption may now
be written as follows :
( )
0 0 1 2
Q q h h = . . . (2.3)
1
1
v

v
q
and
* *
0 1 4
1 1
W m
q h h
=

. . . (2.4)

2 1
w h h =
Effect of Condenser Pressure
An increase in condenser pressure, similarly results in a decrease in the
refrigerating capacity and an increase in power consumption, as seen from the
changed cycle 1 -2'-3'-4' for t
k
' = 45C in Figure 2.6. The decrease in refrigerating
capacity is due to a decrease in the refrigerating effect and volumetric efficiency.
The increase in power consumption is due to increased mass flow (due to
decreased refrigerating effect) and an increase in specific work (due to increased
pressure ratio), although the isentropic line remains unchanged. Accordingly, one
can write for the ratios
v
v
h h
h h
Q
Q
q
q
'
4 1
'
4 1
0
'
0

= . . . (2.5)
1 2
1
'
2
4
'
1
4 1
'
*
*'
'
h h
h h
h h
h h
W
W
c
c

= =
c
c
. . . (2.6)

Figure 2.6 : Effect of Condenser Pressure
It is obvious that COP decreases both with decreasing evaporator and increasing
condenser pressures.
It may, however, be noted that the effect of increase in condenser pressure is not as
server, on the refrigerating capacity and power consumption per ton of
refrigeration, as that of the decrease in evaporator pressure.
Effect of Suction Vapour Superheat
Superheating of the suction vapour is advisable in practice because it ensures
complete vaporization of the liquid in the evaporator before it enters the
compressor. Also, in most refrigeration and air-conditioning systems, the degree of
superheat serves as a means of actuating and modulating the capacity of the
expansion valve. It has also been seen that for some refrigerants such as Freon 12,
maximum COP is obtained with superheating of the suction vapour.

23
Refrigeration Cycle

Figure 2.7: Effect of Suction Vapour Superheat
It can be seen from Figure 2.7, that the effect of superheating of the vapour from
t
1
= t
0
to t
1
'

is as follows :
(a) Increase in specific volume of suction vapour from v
1
to v
1

(b) Increase in refrigerating effect from (h
1
h
4
) to (h
1
h
4
)
(c) Increase in specific work from (h
2
h
1
) to (h
2
' h
1
')
It is to be noted that (h
2
' h
1
') is greater than (h
2
h
1
). This is because, although
the pressure ratio is the same for both lines, the initial temperature t
1
,

is greater
than t
1
and the work given by the expression
( )
(

1 /
1
1
1 2
1

p p
RT

Increases with the initial temperature. That is why isentropic lines on the
p-h diagram become flatter in higher temperatures. An increase in specific volume
decreases the capacity. On the contrary, an increase in refrigerating effect will
increase the capacity effect of super- heating is to theoretically reduce the capacity
in ammonia systems and to increase it in Freon 12 systems.
Effect of Liquid Subcooling
It is possible to reduce the temperature of the liquid refrigerant to within a few
degrees of the temperature of the water entering the condenser. In some condenser
designs it is achieved by installing a sub-cooler between the condenser and the
expansion valve.
The effect of sub-cooling of the liquid from t
3
= tk to t
3'
is shown in
Figure 2.8. It will be seen that sub-cooling reduces flashing of the liquid during
expansion and increases the refrigerating effect. Consequently, the piston
displacement and horsepower per ton are reduced for all refrigerants. The percent
gain is less pronounced in the case of ammonia because of its larger latent heat of
vaporization as compared to liquid specific heat.

Figure 2.8 : Effect of Liquid Subcooling

24
Refrigeration and Air
Conditioning
Normally, cooling water first passes through the subcooler and then through the
condenser. Thus, the coolest water comes in contact with the liquid being
subcooled. But this results in a warmer water entering the condenser and hence a
higher condensing temperature and pressure. Thus, the advantage of subcooling is
offset by the increased work of compression.
This can be avoided by installing parallel cooling water inlets to the subcooler and
condenser. In that case, however, the degree of subcooling will be small and the
added cost of the subcooler and pump work may not be worthwhile. It may be
more desirable to use the cooling water effectively in the condenser itself to keep
the condensing temperature as near to the temperature of the cooling water inlet as
possible.
2.2.4 Carnot Refrigeration Cycle
In refrigeration system, the Carnot cycle considered is reversed Carnot cycle. We know
that a heat engine working on Carnot engine has the highest efficiency. Similarly, a
refrigeration system working on the reversed cycle, has the maximum coefficient of
performance.

(a) p-v Diagram (b) T-s Diagram
Figure 2.9 : Reversed Carnot Cycle
A reversed Carnot cycle, using air as the working medium is shown on p-v and T-s
diagrams in Figures 2.9(a) and (b) respectively. At point 1, let p
1
, v
1
, T
1
be the pressure,
specific volume and temperature of air respectively.
The four processes of the cycle are as follows:
Isentropic Compression Process
The air is compressed isentropically as shown by the curve 1-2 on p-v and T-s
diagrams. During this process, the pressure of air increases from p
1
to p
2
, specific
volume decreases from v
1
to v
2
and temperature increases from T
1
to T
2
. We know
that during isentropic compression, no heat is absorbed or rejected by the air.
Isothermal Compression Process
The air is now compressed isothermally (i.e. at constant temperature, T
2
= T
3
) as
shown by the curve 2-3 on p-v and T-s diagrams. During this process, the pressure
of air increases from p
2
to p
3
and specific volume decreases from v
2
to v
3
. We know
that the heat rejected by the air during isothermal compression per kg of air,
q
2-3
= area 2-3-3'-2'
= T
3
(s
2
s
3
)
= T
2
(s
2
s
3
)
Isentropic Expansion Process
The air is now expanded isentropically as shown by the curve 3-4 on p-v and T-s
diagrams. The pressure of air decreases from p
3
to p
4
, specific volume increases
from v
3
to v
4
and temperature decreases from T
3
to T
4
. We know that during
isentropic expansion, no heat is absorbed or rejected by the air.

25
Refrigeration Cycle
Isothermal Expansion Process
The air is now expanded isothermally (i.e. at constant temperature, T
4
= T
1
) as
shown by the curve 4-1 on p-v and T-s diagrams. During this process, the pressure
of air decreases from p
4
to p
1
and specific volume increases from v
4
to v
1
. We know
that the heat absorbed by the air during isothermal compression per kg of air,
q
4-1
= area 4-1-2'-3'
= T
4
(s
1
s
4
)
= T
4
(s
2
s
3
)
= T
1
(s
2
s
3
)
We know that work done during the cycle per kg of air
= Heat rejected Heat absorbed
= q
2-3
q
4-1

= T
2
(s
2
s
3
) T
1
(s
2
s
3
)
Therefore, coefficient of performance of the refrigeration system working on
reversed Carnot cycle,
C.O.P. =
HeatAbsorbed
WorkDone

=
( )
( )( )
1 2 3
2 1 2 3
T s s
T T s s

=
1
2 1
T
T T

2.2.5 Temperature Limitations for Reversed Carnot Cycle
We have seen that the C.O.P. of the reversed Carnot cycle is given by,
C.O.P. =
1
2 1
T
T T

where T
1
= Lower temperature, and
T
2
= Higher temperature.
The C.O.P. of the reversed Carnot cycle can be improved by
(a) Decreasing the higher temperature (i.e. temperature of hot body, T
2
) or
(b) Increasing the lower temperature (i.e. temperature of cold body, T
1
).
It may be noted that temperature T
1
and T
2
cannot be varied at will, due to certain
functional limitations. It should be kept in mind that the higher temperature (T
2
) is the
temperature of cooling water or air available for rejection of heat and the lower
temperature (T
1
) is the temperature to be maintained in the refrigerator. The heat transfer
will take place in the right direction only when the higher temperature is more than the
temperature of cooling water or air to which heat is to be rejected, while the lower
temperature must be less than the temperature of substance to be cooled.
Thus if the temperature of cooling water or air (i.e. T
2
) available for heat rejection is low,
the C.O.P. will be high. Since T
2
in winter is less than T
2
in summer, therefore, C.O.P. in
winter will be higher than C.O.P. in summer. In other words, the Carnot refrigerator
works more efficiently in winter than in summer. Similarly, if the lower temperature (T
1
)
is high, the C.O.P. of the Carnot refrigerator will be high.

26
Refrigeration and Air
Conditioning
2.2.6 Difference between Refrigeration and Heat Pump System
The major difference between the refrigeration and heat pump system is that refrigerator
delivers heat from lower temperature to a higher temperature, whereas heat pump
delivers heat from higher temperature to lower temperature body. The difference between
refrigerator and heat pump is shown in the Figure 2.10 schematically.


















Figure 2.10 : Schematic Representation of Refrigerator and Heat Pump
2.3 VAPOUR ABSORPTION SYSTEM
The vapour absorption refrigeration is heat operated system. It is quite similar to the
vapour compression system. In both the systems, there are evaporator and condenser. The
process of evaporation and condensation of the refrigerant takes place at two different
pressure levels to achieve refrigeration in both the cases. The method employed to create
the two pressure levels in the system for evaporation and condensation of the
refrigeration makes the two processes different. Circulation of refrigerant in both the
cases is also different.
In the absorption system the compressor of the vapour compression system is replaced by
the combination of absorber and generator. A solution known as the absorbent, which
has an affinity for the refrigerant used, is circulated between the absorber and the
generator by a pump (solution pump). The absorbent in the absorber draws (or sucks) the
refrigerant vapour formed in the evaporator thus maintaining a low pressure in the
evaporator to enable the refrigerant to evaporate at low temperature. In the generator the
absorbent is heated. There by releasing the refrigerant vapour (absorbed in the absorber)
as high pressure vapour, to be condensed in the condenser. Thus the suction function is
performed by absorbent in the absorber and the generator performs the function of the
compression and discharge. The absorbent solution carries the refrigerant vapour from
the low side (evaporatorabsorber) to the high side (generator-condenser). The liquefied
refrigerant flows from the condenser to the evaporator due to the pressure difference
between the two vessels; thus establishing circulation of the refrigerant through the
system.

Higher Temperature

Higher Temperature

RE

Lower Temperature

Lower Temperature

HP
RE =Refrigerator
HP = Heat Pump

27
Refrigeration Cycle
Figure 2.11 is a schematic diagram of the absorption cycle. As can be seen from the
figure, the refrigerant and absorbent have separate flow paths. The refrigerant path is:
Evaporator Absorber Generator Condenser Evaporator and for the absorbent
it is,
Absorber Generator Absorber
The absorbent solution passing from the generator to the absorber is hot and ha to be
cooled. On the other hand the absorbent solution sent to the generator is cooled and has
to be heated in the generator for the regeneration of the refrigerant. A shell and tube heat
exchanger is introduced between the generator and the absorber.

Figure 2.11 : Schematic Diagram of Absorption System of Refrigeration

Figure 2.12 : Schematic Sketch of a Lithium-Bromide Absorption Machine Single Stage
There is number of vapour absorption system depending on the absorbent e.g. ammonia
absorbent system, lithium bromide absorption system etc. Ammonia absorbent systems
were used in the early stages of refrigeration. This system uses ammonia as the
refrigerant and water as absorbent. In lithium bromide absorption system lithium bromide
salt solution is used as the absorbent and water as the refrigerant. A concentrated solution
of lithium bromide has a great affinity for water. Since water is the refrigerant, the
refrigerant operating temperature in the evaporator has to be above the freezing point of
water (0
o
C) of water.

28
Refrigeration and Air
Conditioning
2.4 ILLUSTRATIVE PROBLEMS
Example 2.1
Carnot refrigeration cycle absorbs heat at 270 K and rejects heat at 300 K.
(a) Calculate the coefficient of performance of this refrigeration cycle.
(b) If the cycle is absorbing 1130 kJ/min at 270 K, how many kJ of work
is required per second.
(c) If the Carnot heat pump operates between the same temperatures as
the above refrigeration cycle, what is the coefficient of performance.
(d) How many kJ/min will the heat pump deliver at 300 K if it absorbs
1130 kJ/min at 270 K.
Solution
Given : T
1
= 270 K; T
2
= 300 K
(a) Coefficient of performance of Carnot refrigeration cycle
We know that coefficient of performance of Carnot refrigeration
cycle,
(C.O.P.)
R
=
1
2 1
T
T T
=
270
300 270
= 9 Ans.
(b) Work required per second
Let WR = Work required per second
Heat absorbed at 270 K (i.e. T
1
),
Q
1
= ll30 kJ/min= 18.83 kJ/s
We know that (C.O.P)
R
=
1
R
Q
W


1
18.83
( . . ) 9
R
R
Q
W
COP
= =
W
R
= 2.1 kJ/s Ans.
(c) Coefficient of performance of Carnot heat pump
We know that coefficient of performance of a Carnot heat pump,
(C.O.P.)p =
2
2 1
T
T T
=
300
300 270
= 10 Ans.
(d) Heat delivered by heat pump at 300 K
Let Q
2
= Heat delivered by heat pump at 300 K.
Heat absorbed at 270 K (i.e. T1),
Q
1
= 1130 kJ/min (Given)
We know that (C.O.P.)p =
2
2 1
Q
Q Q

Q
2
= 1256 kJ/min Ans.
Example 2.2
The capacity of a refrigerator is 200 TR when working between 6C and 25
o
C.
Determine the mass of ice produced per day from water at 25C. Also find the
power required to drive the unit. Assume that the cycle operates on reversed
Carnot cycle and latent heat of ice is 335 kJ/kg.

29
Refrigeration Cycle
Solution
Given : Q = 200TR; T
1
= 6C = 6 + 273 = 267 K; T
2
= 25C;
Tw = 250 C : hfg = 335 kJ/kg
Mass of ice produced per day
We know that heat extraction capacity of the refrigerator
= 200 210 = 42000 kJ/min
heat removed from 1 kg of water at 25C to form ice at 0C
(1 TR = 210 kJ/min)
= Mass Sp. heat Rise in temperature + hfg (ice)
= 1 4.187 (25 0) + 335 = 439.7 kJ/kg
Mass of ice produced per min
42000
439.7
= = 95.52 kg/min
and mass of ice produced per day = 95.52 60 24 = 137550 kg = 137.55 tonnes
Power required to drive the unit
We know that C.O.P. of the reversed Carnot cycle
1
2 1
267
8.6
298 267
T
T T
= = =


COP. = (Heat extraction capacity)/(Work done per mm)
Work done per min = 42 000/8.6 = 4884 kJ/min
Power required to drive the unit
=
4884
60
= = 81.4 kW Ans.
Example 2.3
Five hundred kgs of fruits are supplied to a cold storage at 20
o
C. The cold storage
is maintained at 5C and the fruits get cooled to the storage temperature in
10 hours. The latent heat of freezing is 105 kJ/kg and specific heat of fruit is
1.256 kJ/kg K. Find the refrigeration capacity of the plant.
Solution
Given : m = 500 kg; T
2
= 20C = 20 + 273 = 293K;
T
1
= 5C = 5 + 273 = 268 K; hfg = 105 kJ/kg, cF = 1.256 kJ/kg K
We know that heat removed from the fruits in 10 hrs,
Q
1
= m cF (T
2
T
1
)
= 500 1.256(293 268) = 15700 kJ
and total latent heat of freezing,
Q
2
= m . hfg = 500 105 = 52500 kJ
Total heat removed in 10 hrs,
Q = Q
l
+ Q
2
= 15700 + 52500 = 68200 kJ
and total heat removed in one minute
= 68200/10 60 = 113.7 kJ/min
Refrigeration capacity of the plant
= 113.7/210 = 0.541 TR (1 TR = 210 kJ/min) Ans.

30
Refrigeration and Air
Conditioning
Example 2.4
A cold storage plant is required to store 20 tonnes of fish. The fish is supplied at a
temperature of 30C. The specific heat of fish above freezing point is
2.93 kJ/kg K. The specific heat offish below freezing point is 1.26 kJ/kg K. The
fish is stored in cold storage which is maintained at 8
o
C. The freezing point of
fish is 4C. The latent heat of fish is 235 kJ/kg. If the plant requires 75 kW to
drive it, find
(a) The capacity of the plant, and
(b) Time taken to achieve cooling.
Assume actual C.O.P. of the plant as 0.3 of the Carnot C.O.P.
Solution
Given : m = 20 t = 20000 kg; T
2
= 30C = 30 + 273 = 303 K;
cAF = 2.93 kJ/kg K; cBF = 1.26 kJ/kgK; T
1
= 8C = 8 + 273 = 265 K;
T
3
= 4C = 4 + 273 = 269 k; hfg = 235 kJ/kg; P = 75 kW = 75 kJ/s
(a) Capacity of the plant
We know that Carnot C.O.P.
=
1
2 1
T
T T
=
265
303 265
= 6.97
Actual COP. = 0.3 6.97 = 2.091
and heat removed by the plant
= Actual COP. Work required
= 2.091 75 = 156.8 kJ/s = 156.8 60 = 9408 kJ/min
Capacity of the plant
= 9408 /210 = 44.8 TR Ans.
(b) Time taken to achieve cooling
We know that heat removed from the fish above freezing point,
Q
1
= m c
AF
(T
2
T
3
)
= 20000 2.93 ( 303 269)
= 1.992 10
6
kJ
Similarly, heat removed from the fish below freezing point,
Q
2
= m x c
BF
(T
3
T
1
)
= 20000 1.26 (269 265)
= 0.101 10
6
kJ
and total latent heat of fish,
Q
3
= m h
fg (fish)

= 20000 235
= 4.7 10
6
kJ
Total heat removed by the plant
= Q
1
+ Q
2
+ Q
3
= 1.992 10
6
+ 0.101 10
6
+ 4.7 10
6

= 6.793 10
6
kJ
and time taken to achieve cooling
=
6
6.793 10
9408

= 722 min = 12.03 h Ans.

31
Refrigeration Cycle
2.6 SUMMARY
A vapour compression refrigeration system is an improved type of air refrigeration
system in which a suitable working substance, termed as refrigerant is used. It condenses
and evaporates at temperatures and pressures close to atmospheric conditions. The
refrigerant used, does not leave the system, but is circulated throughout the system
alternately condensing and evaporating. The vapour absorption system uses heat energy,
instead of mechanical energy as in vapour compression systems, in order to change the
conditions of the refrigerant required for the operation of the refrigeration cycle. In
vapour compression system compressor is used to withdraw the vapour refrigerant from
the evaporator. It then raises its temperature and pressure higher than the cooling agent in
the condenser so that the higher pressure vapour can reject heat in the condenser. But in
the vapour absorption system, the compressor is replaced by an absorber, a pump, a
generator and a pressure reducing valve. These components in vapour absorption system,
perform the same functions as that of a compressor in vapour compression system. In this
system, the vapour refrigerant from the evaporator is drawn into an absorber where it is
absorbed by the weak solution of the refrigerant forming a strong solution. This strong
solution is pumped to the generator where it is heated by some external source. During
the heating, the vapour refrigerant is driven off by the solution and enters into the
condenser where it is liquefied. The liquid refrigerant then flows into the evaporator and
thus the cycle is completed.
2.7 ANSWERS TO SAQs
Refer the relevant preceding texts in the unit or other useful books on the topic listed in
the section Further Readings to get the answers of the SAQs.