WRFU Huawei

WRFU
http://127.0.0.1:52199/hedex/pages/574119981/05 (2009-08-20)/574119...
WRFU
One WCDMA radio frequency unit (WRFU) supports 40 W (2 carriers) and 80 W (4 carriers) power outputs.
Panel
Figure 1 shows the panel of the WRFU. Figure 1 Panel of the WRFU
Function
The direct frequency conversion technique, which is directly implemented in the transmit channel, modulates the baseband signals to WCDMA RF signals. After being filtered and amplified, the RF signals are transmitted to the antenna for transmission through the duplex filter. The uplink RF signals received from the antenna go through down-conversion, amplification, analog-to-digital conversion, digital down-conversion, matched filtering, automatic gain control (AGC). Then, they are sent to the BBU for further processing. Power control and Voltage Standing Wave Ratio (VSWR) detection Reverse power detection Frequency synthesis and loopback test Generation of the CPRI clock, recovery of the CPRI clock of lost synchronization, and alarm detection The WRFU supports 40 W (2 carriers) and 80 W (4 carriers) power outputs.
Principle
1 of 4
9/25/2010 2:05 PM
WRFU
The WRFU consists of the high-speed interface unit, signal processing unit, power amplifier, and duplex unit. Figure 2 shows the principle of the WRFU module. Figure 2 Principle of the WRFU
The functions of the high-speed interface unit are as follows: Transmitting the signals received from the BBU to the signal processing unit Transmitting the signals received from the signal processing unit to the BBU The signal processing unit consists of two uplink RX channels and one downlink TX channel. The functions of the uplink RX channels are as follows: Performing down-conversion of the RF signals to IF signals Amplifying the IF signals and performing IQ demodulation Converting analog signals to digital signals Sampling digital signals Performing matched filtering AGC Encapsulating data The functions of the downlink TX channel are as follows: Decapsulating the clock signals, control signals, and data signals from the BBU and sending them to associated units Shaping and filtering downlink signals Converting digital signals to analog signals and modulating IQ Performing up-conversion of IF signals to the transmit band The power amplifier amplifies the low-power RF signals from the signal processing unit. The functions of the duplexer are as follows: Multiplexing the RX signals and TX signals Enabling RX signals and TX signals to share one antenna channel Filtering the RX/TX signals
LED
Table 1 describes the LEDs on the panel of the WRFU.
2 of 4
9/25/2010 2:05 PM
WRFU
Table 1 LEDs on the WRFU Identity RUN Status ON steady OFF steady 1s ON, 1s OFF 0.125s ON, 0.125s OFF ALM ON steady OFF steady ACT ON steady OFF steady 1s ON, 1s OFF VSWR Off (red) On (red) CPRI0 On (green) On (red) 1 s ON, 1 s OFF (red) CPRI1 On (green) On (red) 1 s ON, 1 s OFF (red) Description The power input is normal, but the module is faulty. There is no power input, or the module is faulty. The module is running properly. The module is loading software or is not started. The module is in the alarm status. No alarm is generated. The module is functional and is connected to the BBU. The module is not connected to the BBU. The module is in the local test status. No VSWR alarm is generated. A VSWR alarm is generated. The CPRI link is normal. The interface module fails to receive signals. The CPRI link is out of lock. The CPRI link is normal. The interface module fails to receive signals. The CPRI link is out of lock.
3 of 4
9/25/2010 2:05 PM
WRFU
Identity
Status
Description
Port
Table 2 describes the ports on the panel of the WRFU. Table 2 Ports on the panel of the WRFU Connector Port for transceiving RF signals CPRI Label ANT_RXB ANT_TX/RXA CPRI0 Connector Type DIN DIN SFP female connector SFP female connector QMA female connector QMA female connector Connecting the BBU, or the upper-level WRFU during the cascading Connecting the lower-level WRFU during the cascading Description Connecting the antenna subsystem
CPRI1
Interconnection port for RX_INB RF receive signals RX_OUTA
Input port of diversity signals in the antenna channel
Output port of diversity signals in the antenna channel
Socket for power supply Commissioning port
PWR
2V2 power connector Introducing power
MON
RJ45
Used for commissioning
Parent topic: Components in the RF Cabinet
Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd.
4 of 4
9/25/2010 2:05 PM

WRFU Huawei

Uploaded by

Copyright:

Available Formats

WRFU Huawei

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

WRFU Huawei

Uploaded by

Copyright:

Available Formats

WRFU

Interconnection port for RX_INB RF receive signals RX_OUTA

Input port of diversity signals in the antenna channel

Output port of diversity signals in the antenna channel

Socket for power supply Commissioning port

2V2 power connector Introducing power

Used for commissioning

Parent topic: Components in the RF Cabinet

Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd.

You might also like