Service Manual: ZS-SN10

ZS-SN10
SERVICE MANUAL
US Model
Canadian Model
E Model
Australian Model
Ver. 1.4 2006.03
US and foreign patents licensed from Dolby Laboratories.
Model Name Using Similar Mechanism
CFD-E95
Optical Pick-up Block Name
KSM-213CDP
Optical Pick-up Name
KSS-213C
SPECIFICATIONS
Battery life
For player:
POWER OUTPUT AND TOTAL HARMONIC

DISTORTION
With 3.2-ohm loads, both channels driven from
150 - 6,300 Hz; rated 1.8 W per channel-minimum
RMS power, with no more than 10 % total
harmonic distortion in AC operation.
SP, KR, TH, AUS models:

FM: 87.5 - 108 MHz
AM: 531 - 1611 kHz (9 kHz step)
530 - 1610 kHz (10 kHz step)
IF
FM: 10.7 MHz
AM: 450 kHz
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
Other Specifications
General
CD player section
Speaker
Full range: 10 cm (4 in.) dia., 3.2 , cone type (2)
Input
LINE IN jack (stereo minijack):
Minimum input level 330 mV
Outputs
Headphones jack (stereo minijack):
For 16 - 64 impedance headphones
Power output
2.3 W + 2.3 W (at 3.2 , 10 % harmonic
distortion)
Power requirements
For player:
US, CND, E, MX, TW models:
120 V AC, 60 Hz
SP, TH, AUS models:
230 V AC, 50 Hz
KR model:
220 V AC, 60 Hz
AUDIO POWER SPECIFICATIONS

(US model only)
CD playback
Sony R20P: approx. 2 h
Sony alkaline LR20: approx. 8 h
Radio reception
Sony R20P: approx. 10 h
Sony alkaline LR20: approx. 25 h
System
Compact disc digital audio system
Laser diode properties
Emission duration: Continuous
Laser output: Less than 44.6 W
(This output is the value measured at a distance of about
200 mm from the objective lens surface on the optical
pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20 000 Hz +0/1 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
US, CND, E, MX, TW models:
FM: 87.5 - 108 MHz
AM: 530 - 1710 kHz
9 V DC, 6 size D (R20) batteries

For remote control:
3 V DC, 2 size AAA (R03) batteries
Power consumption
16 W
Dimensions
Approx. 500 145 230 mm (w/h/d)
(19 3/4 5 3/4 9 1/8 inches) (incl. projecting parts)
Mass
Approx. 3.8 kg (8 lb. 6 oz) (incl. batteries)
Supplied accessories
AC power cord (1) (US, CND, E, MX, TW models)
Mains lead (1) (SP, KR, TH, AUS models)
Remote control (1)
CD-ROM (SonicStage) (1)
SonicStage Installation/Operating Guide (1)
Design and specifications are subject to change without
notice.
Abbreviation
AUS : Australian model
CND: Canadian model
KR : Korean model
MX : Mexican model
SP : Singapore model
TH : Thai model
TW : Taiwan model
PERSONAL AUDIO SYSTEM

9-879-649-05
2006C05-1
2006.03
Sony Corporation
Personal Audio Division
Published by Sony Techno Create Corporation
ZS-SN10
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
Notes on chip component replacement
Never reuse a disconnected chip component.
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
Keep the temperature of the soldering iron around 270 C
during repairing.
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, metallized knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The limit indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
TABLE OF CONTENTS
1.
SERVICING NOTES ................................................ 3
2.
GENERAL ................................................................... 4
3.
DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
Disassembly Flow ...........................................................

Cabinet Top Assy .............................................................
MAIN Board ....................................................................
Cabinet Front Assy ..........................................................
LCD Board ......................................................................
CD Block Assy ................................................................
Optical Pick-up (KSS-213C) ...........................................
CD Lid .............................................................................
4.
ELECTRICAL ADJUSTMENTS .......................... 10
5.
DIAGRAMS
5-1.
5-2.
5-3.
5-4.
5-5.
5-6.
5-7.
5-8.
5-9.
5-10.
5-11.
5-12.
5-13.
Block Diagram CD Servo Section ............................

Block Diagram TUNER Section ..............................
Block Diagram MAIN Section ................................
Printed Wiring Board CD Board ..............................
Schematic Diagram CD Board .................................
Printed Wiring Board TUNER Board .......................
Schematic Diagram TUNER Board .........................
Printed Wiring Boards MAIN Section .....................
Printed Wiring Boards POWER Section ..................
Schematic Diagram MAIN Section (1/2) .................
Schematic Diagram MAIN Section (2/2) .................
Printed Wiring Boards PANEL Section ....................
Schematic Diagram PANEL Section ........................
6.
EXPLODED VIEWS
6-1.
6-2.
6-3.
6-4.
6-5.
6-6.
Cabinet Section ................................................................

Cabinet Front Section ......................................................
Cabinet Top Section-1 .....................................................
Cabinet Top Section-2 .....................................................
Cabinet Bottom Section ...................................................
Optical Pick-up Section (KSM-213CDP) .......................
7.
ELECTRICAL PARTS LIST .................................. 39
6
6
7
7
8
8
9
9
12
13
14
16
17
18
19
20
21
22
23
24
25
33
34
35
36
37
38
SAFETY-RELATED COMPONENT WARNING!!
To Exposed Metal
Parts on Set
0.15 F
1.5 k
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
AC
voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
ATTENTION AU COMPOSANT AYANT RAPPORT

LA SCURIT!
LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES
PICES SONT CRITIQUES POUR LA SCURIT DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PICES SONY DONT LES NUMROS SONT
DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS
PUBLIS PAR SONY.
ZS-SN10
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION

CHECK
During normal operation of the equipment, emission of the laser
diode is prohibited unless the upper lid is closed while turning ON
the S801. (push switch type)
The following checking method for the laser diode is operable.
Method
Emission of the laser diode is visually checked.
1. Open the upper lid.
2. Push the S801 as shown in Fig.1.
Note: Do not push the detection lever strongly, or it may be bent or damaged.
3. Press the u button.

4. Check the object lens for confirming normal emission of the
laser diode. If not emitting, there is a trouble in the automatic
power control circuit or the optical pick-up.
In this operation, the object lens will move up and down 2
times along with inward motion for the focus search.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
Unleaded solder melts at a temperature about 40 C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
S801
Fig.1 Method to push the S801
ZS-SN10
SECTION 2
GENERAL
This section is extracted from

instruction manual.
Basic Operations
Playing a CD
1, 2
Press u (N on the remote) (direct

power-on).
The player plays all the tracks once.
Display
Audio CD
Track number
ATRAC CD/MP3 CD*
Playing time
File name
File number
Playing time
* When playing an MP3 CD, MP3

appears in the display.
Connect the supplied AC power cord.
Press PUSH Z OPEN/CLOSE to

open the CD lid and place the CD on
the CD tray.
With the label side up
Note
Before playing an ATRAC
CD/MP3 CD, this player
reads all file and group
information on the CD.
Depending on the file
structure, it may take more
than a minute to read them.
During this time, Reading
is displayed.
Use these buttons for additional operations

POWER
u
x
VOLUME , +
, +
i
>
Press PUSH Z OPEN/CLOSE to

close the CD lid.
Tips
To listen through
headphones, connect the
headphones to the i
(headphones) jack.
Playback starts from the
track you last stopped
playing (Resume play).
To cancel the resume play
to start play from the
beginning of the first track,
press x in stop mode.
To
Press
adjust the volume
VOLUME +* 1, (VOL +* 1, on the

remote)
stop playback
pause playback
u*1 (X on the remote)

Press the button again to resume play after
pause.
go to the next track
>
go back to the
previous track
*1 The button has a tactile dot.
To
Press
select a group*2
+ to go forward and to go
backward
remove the CD
PUSH Z OPEN/CLOSE*3
turn on/off the player
POWER
*2 This function works for ATRAC CDs/MP3 CDs only.

*3 Once you open the CD lid, the track to start play will change to
the beginning of the first track.
Notes
If ATRAC3plus files and
MP3 files are recorded on
the same CD, this CD
player plays the
ATRAC3plus first.
The playback capability of
this CD player may vary
depending on the quality of
the disc and the condition of
the recording device.
Characters that can be
displayed on this CD player
are listed below.
A to Z
a to z
0 to 9
! " # $ % & ' ( ) * + , - . / :
;<=>?@[\]^_`{|}
~
If you use other characters
on your computer using
software such as
SonicStage, they are
displayed as on this CD
player.
On a disc that has
ATRAC3plus/MP3 files, do
not save files in other
formats and do not make
unneccessary groups.
The structure of ATRAC CDs/MP3 CDs

ATRAC CDs/MP3 CDs consist of files and groups. A
file is equivalent to a track of an audio CD. A group
is a bundle of files and is equivalent to an album.
For MP3 CDs, this CD player recognizes an MP3 folder as
a group so that ATRAC CDs and MP3 CDs can be
operated in the same way.
In this manual, we use the word track in description of
the operations available for both ATRAC CDs/MP3 CDs
and audio CDs, and the word file for the operations
available for ATRAC CDs/MP3 CDs only.
Playing order of ATRAC CDs and MP3 CDs
For ATRAC CDs, files are played in the order selected in
SonicStage.
For MP3 CDs, the playing order may differ depending on
the method used to record MP3 files on the disc. In the
following example, files are played in order of 1 to 7.
Group
File
ATRAC CD
MP3 CD
Notes on ATRAC CDs

Maximum number of groups: 255
Maximum number of files: 999
CD-Rs/CD-RWs recorded in the ATRAC3plus format cannot be
played on your computer.
Notes on MP3 CDs
Maximum number of groups: 255
Maximum number of files: 511
Maximum directory level: 8
A group that does not include an MP3 file is skipped.
Be sure to add the file extension mp3 to the file name.
However, if you add the file extension mp3 to a file other than
an MP3 file, the player will not be able to recognize the file
properly.
This player can play bit rates of 32 to 320 kbps, and sampling
frequencies of 32/44.1/ 48 kHz.
To compress a source in an MP3 file, we recommend setting the
compression parameters to 44.1 kHz, 128 kbps, and
Constant Bit Rate.
To record up to the maximum capacity, set the writing software
to halting of writing.
To record to the maximum capacity at one time up on media that
has nothing recorded on it, set the writing software to Disc at
Once.
ZS-SN10
Listening to the radio

Use these buttons for additional operations
2
POWER
VOLUME , +
MODE
Tip
If the FM broadcast is noisy,
press MODE repeatedly until
Mono appears in the
display and radio will play in
monaural.
Connect the supplied AC power cord.
Press RADIOBANDAUTO
PRESET repeatedly until the band
you want appears in the display
(direct power-on).
To
Press
adjust the volume
VOLUME +*, (VOL +*, on the

remote)
turn on/off the radio
POWER
* The button has a tactile dot.

Display
To improve broadcast reception

Reorient the antenna for FM. Reorient the player itself for
AM.
Hold down TUNE + or until the

frequency digits begin to change in
the display.
The player automatically scans the
radio frequencies and stops when it
finds a clear station.
Indicates an FM
stereo broadcast
for FM
for AM
If you cant tune in a station, press

TUNE + or repeatedly to change
the frequency step by step.
ZS-SN10
SECTION 3
DISASSEMBLY
This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
SET
3-2. CABINET TOP ASSY

(Page 6)
3-3. MAIN BOARD

(Page 7)
3-6. CD BLOCK ASSY

(Page 8)
3-4. CABINET FRONT ASSY

(Page 7)
3-7. OPTICAL PICK-UP

(KSS-213C)
(Page 9)
3-8. CD LID
(Page 9)
3-5. LCD BOARD

(Page 8)
Note: Follow the disassembly procedure in the numerical order given.
3-2. CABINET TOP ASSY

4 three screws
(B3)
3 Open the CD lid.
2 telescopic antenna (ANT1)
5 Lift the handle.
7 three screws
(B3)
1 screw (M3)
qs cabinet top assy
qa flexible flat cable (4 core)

(CN403)
6 two screws
(B3)
9 connector
0 wire (flat type) (23 core)

(CN102)
ZS-SN10
3-3. MAIN BOARD

3 connector (CN901)
2 connector (CN301)
5 flexible flat cable
(11 core) (CN807)

(11 core) (CN806)
7 two screws
(B2.6)

(11 core) (CN801)
8 MAIN board
1 connector (CN302)
3-4. CABINET FRONT ASSY
3 two screws
(B3)
4 five screws
(B3)
5 screw (B3)
6 cabinet front assy
1 connector
(CN323)
2 two screws
(B3)
ZS-SN10
3-5. LCD BOARD
2 speaker box (L)

1 four screws
(B3)
5 four screws
(B2.6)
3 four screws
(B3)
6 two screws
(B2.6)
7 two screws
(B2.6)
4 speaker box (R)
8 LCD board
3-6. CD BLOCK ASSY
2 CD block assy
1 four screws
ZS-SN10
3-7. OPTICAL PICK-UP (KSS-213C)

1 CD cover
5 optical pick-up
(KSS-213C)
4 flexible flat cable (16 core)
3 sled shaft
2 gear (A)
3-8. CD LID
9 CD lid
5
7 boss
6 claw
8 boss
1 claw
2 CD spring
3 screw (B2.6)
4 damper
ZS-SN10
Ver. 1.1
SECTION 4
ELECTRICAL ADJUSTMENTS
0 dB=1 V
TUNER SECTION
AM IF ADJUSTMENT
[AM]
Setting:
Function: RADIO
RADIO/BAND, AUTO PRESET button: AM
AM RF signal
generator
T1
Adjust for a maximum reading on level meter

450 kHz
AM FREQUENCY COVERAGE ADJUSTMENT
Put the lead-wire

antenna close to
the set.
level meter
Adjustment Part
Frequency Display
Reading on Digital Voltmeter
L4
530 kHz (531 kHz)

1,710 kHz
1.0 0.05 V
Confirmation
32
+
set
30% amplitude
modulation by
400 Hz signal
Output level:
as low as possible
T2
10.7 MHz
FM FREQUENCY COVERAGE ADJUSTMENT

Adjustment Part Frequency Display Reading on Digital Voltmeter
level meter
32
+
i jack (J301)
L2
Confirmation
108 MHz
87.5 MHz
3.0 0.2 V
1.3 0.3 V
FM TRACKING ADJUSTMENT
L1
87.5 MHz
CT1
108 MHz
Adjustment and Connecting Location: TUNER board

(See page 11)
digital voltmeter
TUNER board
TP (VT)
TP (GND)
620 kHz (621 kHz)

1,400 kHz (1,404 kHz)
FM IF ADJUSTMENT
Adjust for a minimum reading on level meter
set
TUNER board
TP (GND)
5.3 0.7 V (5.2 0.6 V)
): Singapore, Korean, Thai and Australian models
L3
CT3
TUNER board
FM RF signal
TP (ANT)
generator
0.01 F
100 k
Repeat the procedures in each adjustment several times, and

the tracking adjustments should be finally done by the trimmer
capacitors.
Remove FM antenna in FM adjustment.
10
(1,611 kHz)
AM TRACKING ADJUSTMENT
i jack (J301)
[FM]
Setting:
Function: RADIO
RADIO/BAND, AUTO PRESET button: FM
75 kHz frequency
deviation by 1 kHz
signal
Output level:
as low as possible
): Singapore, Korean, Thai and Australian models
ZS-SN10
Adjustment and Connecting Location:
CD SECTION
TUNER Board (Component Side)
FOCUS BIAS CHECK

1. Connect the oscilloscope to TP (RFACO) and TP (VC) on the
CD board.
2. Insert the disc (PATD-012). (Part No.: 4-225-203-01)
3. Press the u button.
4. Confirm that the oscilloscope waveform is as shown in the
figure below. (eye pattern)
A good eye pattern means that the diamond shape () in the
center of the waveform can be clearly distinguished.
T2 FM IF Adjustment
L4
AM Frequency Coverage Adjustment
T1 AM IF Adjustment
L2
FM Frequency Coverage Adjustment
RF signal reference waveform (eye pattern)

L1
CT1
FM Tracking Adjustment
VOLT/DIV: 0.2 V (with the 10: 1 probe in use.)

TIME/DIV: 200 ns
0.5 to 1.1 Vp-p
CT3
L3
AM Tracking Adjustment
When observing the eye pattern, set the oscilloscope
for AC range and raise vertical sensitivity.
TUNER Board (Conductor Side)

Checking Location:
TP
(VT)
CD Board (Conductor Side)
TP
(ANT)
TP
(GND)
TP
(VC)
IC201
TP
(RFACO)
ZS-SN10
11
11
ZS-SN10
SECTION 5
DIAGRAMS
5-1. BLOCK DIAGRAM CD SERVO SECTION
OPTICAL
PICK-UP BLOCK
(KSM-213CDP)
A
57 A
58 B
59 C
60 D
50 E
51 F
LD
AUTOMATIC
POWER CONTROL
Q321
RFACO 70
71 RFACI
CD-L
AOUT1 112
AOUT2 117
XTAI 109
X202
16.9344MHz
66 LD
XTAO 108
67 PD
PD
R-ch is omitted due to same as L-ch.

SIGNAL PATH
S201
(LIMIT)
SSTP 39
CD +3.3V
: CD PLAY
CD DSP
IC201
2-AXIS
DEVICE
FCS
TRK+
TRK
SL+
M402
(SLED)
12 CH2OUTF
CH2FIN 6
45 FFDR
11 CH2OUTR
13 CH1OUTR
14 CH1OUTF
CH2RIN 7
CH1RIN 5
CH1FIN 4
46 FRDR
44 TRDR
43 TFDR
17 CH3OUTF
CH3FIN 23
41 SFDR
18 CH3OUTR
CH3RIN 22
42 SRDR
16 CH4OUTF
OPIN+ 2
38 MDP
M
SL
SP+
M401
(SPINDLE)
SYSTEM CONTROLLER
IC801 (1/2)
FOCUS/TRACKING COIL DRIVER,

SLED/SPINDLE MOTOR DRIVER
IC402
FCS+
DATA
CLOK
XLAT
SENS
SCOR
89
11
16
20
26
DATA2
CLOK2
XLAT2
REQ
IREQ
ACK
XTACN
12
90
13
14
10
15
7
19
20
55
18
56
58
59
60
61
62
57
63
67
DATA
CLOK
XLAT
SENS
SCOR
IDATA2
ODATA2
CLOK2
XLAT2
REQ
IREQ
ACK
XTACN
OPOUT 27
SP
A (Page 14)
R-CH
15 CH4OUTR
CH4IN 24
MUTE
XRST
20
68 XRST
66 M-MUTE
S801
(CD LID OPEN/CLOSE DETECT)
53 CD-DOOR
ZS-SN10
12
12
ZS-SN10
5-2. BLOCK DIAGRAM TUNER SECTION
T2
FM IFT
FM/AM RF AMP, MIX, OSC,

FM/AM IF AMP, DET, MPX
IC1
ANT1
FM TELESCOPIC
ANTENNA
FM IF
QUAD
10
L1
FM RF
24
FM
RF-IN
FM
RF AMP
FM
RF-OUT
MIX-OUT
FM
MIX
CF2
FM IF
AMP
FM
DET
DET
-OUT
AF
16
BUFFER
15
MPX
-IN
L-OUT
AF
AMP
MPX
MUTE
R-OUT
TU-L
12
11
B (Page 14)
R-CH
T1
AM IFT
FM
OSC
AM IF
CT1, L1
CF4
CT1
AM
IF-IN
AM IF
AMP
STEREO/
MONO,
FM/AM
AM
DET
D1
AM
RF AMP
AM
MIX
BUFFER
AM
OSC
CT3, L3
AM TRACKING
20
ST
IND
IF
BUFFER
19
BUFFER
17
FM OSC
D3
(1/2)
AM OSC
CT3
OSC
-OUT
18
LPF2/MO-ST
LEVEL
DET
LPF1/BAND
22
AM
RF-IN
ST-IND
L3
AM FERRITE-ROD
ANTENNA
IF-OUT
FM TRACKING
FM
IF-IN
13 14
21
FM FREQUENCY
COVERAGE
AM FREQUENCY
COVERAGE
L2
FM OSC
L4
AM
OSC
D3
(2/2)
D2
VT B+
MUTING
Q808
R MUTING
LOW-PASS
FILTER
20
X1
75kHz
19
XOUT
XIN
LOW-PASS
FILTER
REFERENCE
DIVIDER
13
MO/ST
ST-IND
BAND
BAND
10
IF IN
11
AM IN
12
FM IN
16
PD
17
LP-IN
18
LP-OUT
MW/LW
UNIVERSAL
COUNTER
PHASE
DETECTOR/
CHARGE PUMP
DI
CL
CCB
INTERFACE
1/2
CE
DO
UNLOCK
DETECT
12 BIT
PROGRAMMABLE
DIVIDER
SWALLOW
COUNTER

SIGNAL PATH
: FM
: AM
FM/AM PLL
IC2
SHIFT REGISTER & LATCH
ZS-SN10
13
13
2
3
1
4
R DATA
R CLOCK
R CE
R COUNT
R DATA, R CLOCK, R CE,

R COUNT, R MUTING
C (Page 14)
ZS-SN10
5-3. BLOCK DIAGRAM MAIN SECTION
SIGNAL PATH
: FM
R-CH
(Page 12) A
CD-L
6 CD-L
SEL L 4
TU-L
: CD PLAY
J301
POWER
AMP
IC304
LCH 16
8 RA-L
R-CH
10 LI-L
LINE IN
SC
J322
SI
(Page 13) B
1 R-IN
14
13
MEGA BASS
CONTROL
Q101
INPUT SELECT,
ELECTRICAL VOLUME,
SURROUND/TONE CONTROL
IC301
MUTING
Q121
R-CH
R-CH
SP101
(L-CH)
D301
SP201
(R-CH)
CD +3.3V
CD +2.5V
AMP B+
CD +6V
+2.5V
REGULATOR
IC202
DC/DC
CONVERTER
IC901, Q956
+6V
REGULATOR
Q954
F902
T901
POWER
TRANSFORMER
J901
AC IN
A-MUTE
BL
MEGABASS
X0A
LCD-DB0 LCD-DB7
83
82
78
79
80
100
85 92
LCD-RS
LCD-E
LCD-RW
LCD-RES
X1A
21
SHIFT
SYSTEM CONTROLLER
IC801 (2/2)
15
VOL-CLK
R-DATA
R-CLOCK
R-CE
R-COUNT
R-MUTE
10
X0
(Page
28
29
30
27
31
X1
R DATA, R CLOCK,
R CE, R COUNT,
R MUTING
R DATA
R CLOCK
13)
R CE
R COUNT
R MUTING
VOL-DATA
RECT
D901 904
96 95 94 93
SW +9V
3.3V-CHECK 43
B+ SWITCH
Q813
Q802
X802
32.768kHz
LED DRIVE
Q803
RMC +5V
VH 45
REMOTE CONTROL
RECEIVER
IC401
EEPROM
IC804
SDA
SCL
B+ SWITCH
Q804, 806
SYS +3.3V
P-CON 22
Q801
Q801, 802
SHIFT CLOCK
B+ SWITCH
Q951 953
D801
CD3.3V-ON 25
LIQUID CRYSTAL DISPLAY

LCD401
D402
(LCD BACK LIGHT)
SYS +3.3V
BUCKUP-ON 26
RE B+
X801
4.19MHz
D401
OPR/
BATT
DC LEVEL
DETECT
Q821, 822
VH-CONT 69
64 REMOTE
LOAD CONTROL
SWITCH
Q823, 824
LOAD 70
5
6
8
7
EEP-SDA
EEP-SCL
VM 46
DC LEVEL
DETECT
Q811, 812
AU +6V
(JOG)
ROTARY
ENCODER
S401
VM-CONT 32
98 JOG-A
E.VOL B+
99 JOG-B
VOL-CHECK 44
SYS +3.3V
WAKE UP
SWITCH
Q807
52 WP
RADIO +6V
+6V
REGULATOR
Q955
B+ SWITCH
Q809, 810
TU-ON 24
S402 407
SYS +3.3V
41 KEY0
RESET SIGNAL
GENERATOR
IC803
RESET 77
S410 414, 425
39 KEY1
AC-IN 54
S418 424
40 KEY2
ZS-SN10
14
14
AC CHECK
Q805
+3.3V
REGULATOR
IC802
DRY BATTERY
SIZE "D"
(IEC DESIGNATION R20)
6PCS. 9V
ZS-SN10
Ver. 1.1
Note for Printed Wiring Boards and Schematic Diagrams

Note on Printed Wiring Board:
X : parts extracted from the component side.
Y : parts extracted from the conductor side.
W : indicates side identified with part number.
f
: internal component.
: Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from

the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Circuit Boards Location

Note on Schematic Diagram:
All capacitors are in F unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
All resistors are in and 1/4 W or less unless otherwise
specified.
f
: internal component.
C : panel designation.
Note:
The components identified by mark 0 or dotted line with mark 0 are
critical for safety.
Replace only with part
number specified.
CONTROL (1) board
CD board
Note:
Les composants identifis
par une marque 0 sont critiques pour la scurit.
Ne les remplacer que par une
pice por tant le numro
spcifi.
CONTROL (2) board
A : B+ Line.
H : adjustment for repair.
Power voltage is dc 4.5V and fed with regulated dc power
supply from pin 1 and 2 of CN902 on the BATTERY 1
board, and from pin 3 and 2 as well.
no mark : FM
: AM
(
) : CD PLAY
Voltages are taken with a VOM (Input impedance 10 M).
Voltage variations may be noted due to normal production
tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
Circled numbers refer to waveforms.
Signal path.
F : FM
f : AM
J : CD PLAY
j : LINE IN
Abbreviation
CND : Canadian model
KR
: Korean model
MX
: Mexican model
SP
: Singapore model
TH
: Thai model
TW : Taiwan model
LCD board
POWER board
MAIN board
TUNER board
BATTERY 1 board
H/P board
BATTERY 2 board
ZS-SN10
15
15
ZS-SN10
See page 15 for Circuit Boards Location.
5-4. PRINTED WIRING BOARD CD BOARD
:Uses unleaded solder.
10
11
12
13
14
15
A
CD BOARD (COMPONENT SIDE)
CD BOARD (CONDUCTOR SIDE)

M401
(SPINDLE)
S201
(LIMIT)
C401
R280
C405
C406
R423
C109
C218
C224
C257
C217
R254
C210
C208
IC202
C321
R265
11
R323
Q321
1-865-539-
C273 C265
(11)
C322
CN301
C133
R268
R266
C303
C302
C112
R112
C113
R113
C111
C227
C230
R324
R322
R321
C258
(Page 20)
C132
C301
R115
C259
C256
R260
C261
R259
C323
C204
R249
R267
R256
MAIN BOARD
CN801
C221
C254
R207
CN102
C222
R255
C253
R326
C214
R270
R252
R253
R325
R271
C223
C203
R202
X202
C213
C110
C202
R203
C267
C201
R291
C251
C207
C275
C108
R201
C232
C206
C268
IC201
C205
C215
C101
C102
C220
R401
C404
R278
C271
C252
C270
C269
C107
C219
R276
C105
M402
(SLED)
R277
R275
R103
C103
R108
C424
IC402
R105
R110
R257
C260
R250
C264 R258
R104
R101
C104
C451
R292
C291
C272
R102
R107
R109
R421
R451
C292
R452
R111
C226
OPTICAL PICK-UP
BLOCK
(KSM-213CDP)
11
1-865-539-
ZS-SN10
16
16
(11)
ZS-SN10
Ver. 1.3
5-5. SCHEMATIC DIAGRAM CD BOARD
See page 26 for IC Block Diagram. See page 26 for Waveforms. See page 28 for IC Pin Function Description.
0.01
0.47
C259
100p
C260
C261
R260 0
C264
C273
470p
1000p
C210
0.1
R249
47k
TP
(RFACO)
C208
0.1
R256
22k
C230
100p
C258 220p
R257 470k
R250 1M
C265 0.1
R265 4.7k
C257
0.1
CN301
16P
VC
R259 10k
R268 10k
R267
4.7k
C221
0.1
R258 220k
VCC
R266
1k
R115
0
R324
100k
C322
1
C323
100
10V
C303
10
R321
2.2
C302
10
C301
0.1
E
D
R322
2.2
TP1
APC
R323
0
A
B
Q321
2SA2119K
OPTICAL
AUTOMATIC
C321
1000p
PICK-UP
POWER
CONTROL
BLOCK
GND
KSM-213CDP
C256
0.1
LD
VR
PD
F+
TP
(VC)
T+
RFDCO
AVDD4
PDSENS
LD
AC_SUM
PD
EG_IN
RFC
AVSS4
RFACI
RFACO
AVDD3
BIAS
ASYI
ASYO
VPCO
VCTL
FILI
CLTV
PCO
FILO
SVSS
SVDD
VSS
VDD
SVDD
AVSS3
0.1
SRAMSTB
DATA
F-
(SPINDLE)
SP+
SP-
JTAGTCK
SL+
JTAGTDI
JTAGTDO
VC
JTAGTMS
FEO
R255 1k
TP4 FEI
R254 10k
47p
TEI
TP3 TEI
IOVDD2
DOUT
TEST
AVSS0
TES1
AVDD0
IOVDD1
IOVSS2
CD DSP
PLLVDD
IC201
CXD3014-201R
FRDR
FRDR
PLLVSS
FFDR
XVSS
TRDR
SRDR
XVDD
SFDR
AVDD1
IOVSS1
AOUT1
SSTP
VREFL
MDP
AVSS1
LOCK
AVSS2
VSS
VREFR
VDD
VSS
OPINPREVCC
CH1FIN
CH4CAPA
OPIN+
CH1RIN
CH4IN
GAIN-SW
CH2FIN
OPOUT
CH2RIN
CH3FIN
GND
CH3RIN
CNF4
POWVCC
SLED/SPINDLE
CLOK2
IC402
FAN8040G3
DVDD(3.3V)
R207
0
C133
100p
C226
1
C227
1
C220
0.1
VREF
MOTOR DRIVER
C224
0.1
M-MUTE
D-OUT
GND
COIL DRIVER,
MUTE
FOCUS/TRACKING
CH2OUTF
SVDD
CH2OUTR
MIRR
POWVCC
SVSS
COUT
VDD
SCOR
C2PO
GFS
XPCK
XUGF
SVDD
WFCK
SENS
SVSS
VDD
XLAT
ACK
XLAT2
REQ
DATA2
CLOK
IREQ
VSS
XRST
XTACN
BCK
BCKI
PCMDI
PCMD
LRCKI
OUT
LRCK
GND
IOVSS0
IN
R201 0
C219
0.1
DFCT
CH3OUTR
FOK
IOVDD0
IC202
TK73325WTL-G
R421
0
R292 100
AVDD2
+2.5V REGULATOR
R423
10k
C270 47 4V
AOUT2
DATA
C424
0.1
C404
0.1
C269 47 4V
C291
470p
C292
470p
CN102
23P
TFDR
CH1OUTF
C217
0.1
TFDR
XTAI
C451
47000p
TRDR
CH1OUTR
R291
100
C201
100
10V
R111 100
XTAO
R452
10k
FFDR
CH3OUTF
R112 100
C232
0.1
R271 1M
C202
0.1
C218
0.1
TP2
SPI
C205
0.1
CH4OUTF
R113 100
C251 470p
R451
22k
R270 470
X202
16.9344MHz
C268
22p
R252 10k
CH4OUTR
C275
5p
C215
0.1
M402
(SLED)
TFDR
VDD
C267 22p
R203
0
SL-
C253 470p
FFDR
TEO
C206 0.1
C223
R325 0
FRDR
VSS
0.1
0.1
R326 0
C254 4700p
C252 4700p
R253 1k
C214
C207 100 10V
FEI
TRST
C213
M401
TRDR
SVSS
C222
TEST1
TCLOK2
DGND
L-OUT
C132
22p
C203
100
10V
R202
0
C272
0.1
C204
220p
AGND
R-OUT
R275
100
AVDD(3.3V)
R276
47k
XTACN
R277 100
(Page 22)
XRST
C271
0.1
R278
100
R110 100
IREQ
R103 100
CLOK
R105 100
DATA2
R104 100
C405
0.1
XLAT2
R109 100
C406
0.1
SL-
SP-
R107 100
XLAT
SL+
R108 100
ACK
SP+
REQ
R102 100
SENS
R101 100
R280
0
SCOR
220p
220p
220p
C107
C105 100p
C109
C103 100p
C104
22p
220p
220p
220p
22p
C101
C102
C108
C110
C111
C112 100p
6V
C113 100p
MGND
R401
0
C401
470
10V
S201
(LIMIT)
ZS-SN10
17
17
ZS-SN10
Ver. 1.2
5-6. PRINTED WIRING BOARD TUNER BOARD
10
TUNER BOARD
A
L3
AM FERRITE-ROD
ANTENNA
ANT1
FM TELESCOPIC
ANTENNA
TP
(VT)
TP
(ANT)
(US, CND, E, MX)
1
TP
(GND)
L1
JC24
(SP, TW, KR, TH, AUS)

(SHIELD CASE)
R5
B
MAIN
BOARD
CN802
T1
C13
(US, CND, E, MX)
(Page 20)
L2
11
IC2
L4
IC1
T2
E
C78
C77
ZS-SN10
18
18
11
1-863-438-
(11)
ZS-SN10
Ver. 1.2
See page 26 for IC Block Diagrams.
5-7. SCHEMATIC DIAGRAM TUNER BOARD
See page 26 for Waveform.
TUNER
L3
D3
KV1520NT
AM FERRITE-ROD
L4
C41
220p
ANTENNA
AM OSC
C42
100p
AM FREQUENCY
COVERAGE
C43
22p
JC24
0
L11
1H
JC12
0
JC11
0
R41
10k
CT3
C49
0.01
R40
220k
C47
10p
C39
0.1
(US, CND,E, MX)
C32
1000p
C13
0.01
C33
0.01
R50
1k
R52
0
C51
22p
L2
R33 C30
10k 0.01
R31
4.7k
FM
C65
4.7
50V
R65
10k
R63
10k
C54
220
10V
R51
10k
R24
220
C31
22p
C56
1000p
R54
470
OSC
RF
C52
10p
R14
1k
JC3 0
C24
220p
X1
75KHz
C22
0.1
R11
2.2k
C59
100p
R55 R53
10K 4.7k
C95
1000p
C57
1000p
C20
0.1
C55
100p
C23
1
50V
C21
1
50V
FM IN
BAND
AM IN
MO/ST
FM/AM PLL
IF IN
VDD
BAND
ST-IND
VSS
MW/LW
PD
MUTE
DO
XOUT
CE
LPF1
/BAND
L-OUT
LPF2
/MO-ST
R-OUT
MPX-IN
QUAD
AGC
GND2
DET-OUT
IF-OUT
ST-IND
IF-IN
OSC-
AM OSC
OUT
FM
IF-IN
AM
VCC2
FM OSC
OUT
MIX-
AM
RF-IN
CUT
VCC1
RF-IN
IC1
TA2149BN
FM
GND1
FM/AM IF AMP,DET,MPX
AM LOW
FM
RF-OUT
FM/AM RF AMP,MIX,OSC,
LP-IN
11
FM FREQUENCY
COVERAGE
LP-OUT
L1
FM
C53
0.22
R91
220
D2
KV1471E
CL
C35
0.01
CT1
C80
0.01
R30
22k
(US, CND, E, MX)
XIN
D1
KV1471E
R32
100k
C34
0.01
TP
(VT)
C37
0.01
DI
IC2
LC72137M-TLM
ANT1
FM TELESCOPIC
ANTENNA
C12
4.7
50V
R2
470
D11
1SS355
TP
(ANT)
C1
47p
C60
1000p
R4
10k
JC13
0
C7
5p
C9
10p
T1
C61
100p
JC4
0
C62
100p
C63
100p
R13
1k
R94
1k
D10
1SS355
AM IFT
R92
220
C66
100p
R60
2.2k
R59
2.2k
R56
220
R57
100
L21
10H
C68
100p
CF4
R61
2.2k
JC5
0
CNP1
11P
R-MUTE
R58
2.2k
R-COUNT
R-CLOCK
T2
R-DATA
FM
R1
470
IFT
JC6
R5 0
1K
R-CE
JC33
0
CF2
TU-L
JC2 0
RADIO 6V
JC1 0
R10 47
TU-R
JC34 0
A-GND
R3
10k
C10
1
50V
C78
4700p
C8
1000p
C4
1000p
C11
0.1
C18
220
10V
C14
C15
R-VT
C29
100
10V
C77
4700p
C14, 15
0.01 (SP, TW, KR, TH, AUS)
0.022 (US, CND, E, MX)
ZS-SN10
19
19
C27
100p
C26
100p
TP
(GND)
S-GND
B
MAIN
BOARD
(1/2)
CN802
(Page 22)
ZS-SN10
Ver. 1.2
5-8. PRINTED WIRING BOARDS MAIN SECTION
1
10
11
12
13
14
15
16
17
MAIN BOARD
C127
SP201
(R-CH)
CN301
Semiconductor
Location
SP101
(L-CH)
C227
C961
JW825
R891
C869
R893
R894
R842
R836
R850
R835
R495
Q805
C820
JC804
R865
JC805
JW847
R811
C840
R882
C841
JW848
R863
R862
R884
JW899
JW850
JC806
JW853
R888
R886
Q808
R883
JW851
R846
R845
R839 R840
Q812
R887
Q807
JW852
JW322
JW856
JW802
E
CONTROL (1)
BOARD
CN403
R844
CN805
CN804
JW854
C868
JC807
JW857
JW859
JW860
JW861
JW862
C839
C875
C852
Q811
C850
R838
JW863
JW864
JW871
JW855
R841 C853
JW858
C854
R837
(Page 24)
Q813
11
1-866-321S801
CD LID
OPEN/CLOSE
DETECT
LCD BOARD
CN405
(Page 24)
LCD BOARD
CN402
(Page 24)
ZS-SN10
20
20
(11)
1-866-324-
R499
R498
FB801
FB803
FB804
R813
C837
R864
R849
R800
JW867
JW869
R859
R834
R833
R830
R878
JW868
1
JW870
JW881
JW882
R484
JW883
R486
R483
JW884
R485
R497
JW812
JW820
JW840
R480
C845
C434
8
R851
IC804
Q809
JW846
R812
JW849
C851
C862
C848
C810 C861
C849
JW866
JW891
JW893
JW892
Q810
R106
C856
R832
R856
JW845
R899
R803
R806
R805
C806 R829
JW844
R828
R867
R866
R852
C838
R858
CN302
C874
R110
R111
R206
R211
JW887
R210
(Page 18)
JW894
C811
R827
R868
C855
R801
R818
JW895
R873
R853
R854
(US, CND, E, MX)
CN806
R876
R877
R802
CN807
TUNER
BOARD
CNP1
R874
R880
IC801
R855
CN802
C816
R869
R831
JW885
JW315
C817
R870
R895
Q802
C805
C426
C430
C425
C429
JW874
C818
C814
C813
C812
R881 R879 R875
X802
C831
JW873
JW886
C809
C808
C807
C826
C819
C815
R871
C832
C833
(TW, KR, AUS)
JW317
JW898
JW835
R896
C821
C872
C871
R872
JW872
JW316
X801
JW801
JW832
JW833
(EXCEPT TW, KR, AUS)
JW889
R201
C825
JC801
JW865
C102
R204
JW811
JW830
C842
JW878
JW888
C201
C202
R101
R203
C217
C830
R825
R826
R847
R848
JW877
R103
JW876
JC802
JW818
Q803
R303
R104
C117
Q806
JW875
R817
C118
R304
C101
R105
R305
C203
C103
C218
R205
C422
Q804
R488
R815
C306
R306
C433
C305
R816
C107
C206 C207
C431
JW843
C204
C104
C106
R470
R471
R472
R473
R474
R475
R476
R477
R478
R479
C421
R481
C423
JW842
JW890
C304
C205
R468
R469
C427
C428
C108
C105
C828
C827
C824
JW839
JW318
C208
FB802
JW312
L803
R301
R302
C301
IC301
R112
C424
C303
L806
JW831
4
3
Q801
C823
C829
C302
R213
L802
L801
C109
1
2
JC803
C822
C432
C110
C116
Q201
R114
R218
R102
JW829
IC803
C111
C209
R113
R212
C210
C211
J301
LINE IN
JW826
Q101
JW841
R202
J322
(Page 16)
Q821
JW828
C216
CD
BOARD
CN102
JW827
C802
C112
JW311
JW823
IC802
C803
C214
R116
R215
R120
C114
FB301
Q822
Ref. No.
D301
D801
D802
D905
D906
D907
D908
D951
D953
Location
F-3
B-11
B-12
D-6
D-5
E-6
D-10
D-6
C-7
IC301
IC304
IC801
IC802
IC803
IC804
IC901
I-3
C-3
I-10
F-8
G-10
M-8
C-10
Q101
Q121
Q201
Q221
Q801
Q802
Q803
Q804
Q805
Q806
Q807
Q808
Q809
Q810
Q811
Q812
Q813
Q821
Q822
Q823
Q824
Q951
Q952
Q953
Q954
Q955
Q956
G-4
F-4
G-4
F-4
G-10
G-9
J-8
J-8
I-12
J-7
L-12
L-11
M-4
M-4
L-11
L-12
M-11
E-13
E-13
C-12
D-13
D-5
C-5
D-5
C-7
C-6
D-10
R226
FB201
JW821
C860
C801
FB101
Q824
JW834
R220
C113
R217
C212
R216
R214
C326
Q121
R118
R221 R117
R115
R219
R324
C213
L804
R227
Q221
K
D301
R321
R119
A
A
R309
C956
R121
R323
C324
R127
JW303
R126
(Page 21)
JW879
JW816
R325
C321
C325
R225
L101
CN801
JW815
D907
R326
JW814
JW822
JW808
L201
POWER
BOARD
CN905
C873
C859
JW813
R125
C957
JW807
C959
JW810
Q823
JW819
JW313
JW314
Q953
R955
R901
L301
R496
C907
R902
Q951
L807
D951
IC901
Q956
C958
D905
C954
R954 R903
C955
R957
R958
R950
D908
CN901
JW896
C951
C963
D906
C322
C219 CN303
JW824
R951
C123
Q955
JW809
CN322
C119
C867
R892
Q954
R953
R952
R807
K
Q952
C223
JW321
JW803
JW804
D953
R959
R960
R961
C952
C870
R900
R122
JC808 R956
C953
D801
A
A
C960
C124
C224
R222
R223
IC304
R322
C120
C220
R224
JW806
JW805
C222
C225
R123
JW320
H/P BOARD
D802
R808
C950
C122
R124
C126
JW319
C226
C125
11
(11)
ZS-SN10
5-9. PRINTED WIRING BOARDS POWER SECTION
10
11
12
13
14
15
16
POWER BOARD
BATTERY1 BOARD
JW906
JW905
B
11
1-866-235-
(11)
T901
POWER TRANSFORMER
C
DRY BATTERY
SIZE D
6PCS. 9V
CN902
J901
~AC IN
E
CN904
JW901
C901
D901
BATTERY2 BOARD
C906
CN905
CN903
C902
F902
D902
C908
C904
11
D904
C903
JW903
JW904
H
MAIN
BOARD
CN901
11
1-866-236-
(11)
(Page 20)
ZS-SN10
21
21
D903
1-866-322-
(11)
ZS-SN10
IREQ
SCOR
XLAT
CLOK2
ODATA2
IDATA2
ACK
XLAT2
XRST
XTACN
M-MUTE
(1/2)
REQ
Ver. 1.3
5-10. SCHEMATIC DIAGRAM MAIN SECTION (1/2) See page 26 for Waveforms. See page 31 for IC Pin Function Description.
C812 100p
C813 100p
Q821
RT1P151M-TP-1
Q823,824
Q821,822
R497
100k
LOAD CONTROL
SWITCH
C809
100p
C814 100p
C808
100p
C815 100p
C807
100p
C816 22p
R864
47k
JC807
0
C817 22p
DC LEVEL DETECT
C818 100p
Q824
KTA1271-Y-AT
Q822
RT1N151M-TP-1
S801
C819 100p
CD LID
C811 100p
RESET SIGNAL
GENERATOR
R498
10
IC803
S-80828CNNB
OPEN/CLOSE
R496
2.2k
CN805
2P
DETECT
R867 470k
C873
1000
10V
R895
1k
L803
1H
R896 10k
C821 0.01
R827 1k
C820 0.01
R868 1k
R870 1k
R869 1k
R831 220
R873 220
R871 1k
R872 1k
R877 1k
JC805
0
R865
100k
R866
10k
R894
4.7k
C872 22p
C822 0.01
R876 1k
C869
1
R874 220
R828
47k
Q823
2SC4154TP
R891
1k
R875 1k
R893
47k
R881 1k
VCC
R499
220
R880 1k
JC803
0
R879 1k
GND
RST
R495 4.7k
NC
R863
10k
Q805
RT1N144M
AC CHECK
R852
47k
R807
470
Q807
2SA1602TP
JC804
0
WAKE UP SWITCH
R808
470
D801
KDS121-RTK
C871
22p
C823 22p
X802
Q801
2SC4154TP
C824 10p
C825 220p
R892
220
D802
UDZSTE-175.1B
32.768kHz
C826 47p
MD0
X1
P81
VCC3
P80
LCD-DB0
R468 4.7k
LCD-DB1
R469 4.7k
LCD-DB0
VM
LCD-DB2
R470 4.7k
LCD-DB3
R471 4.7k
LCD-DB4
R472 4.7k
LCD-DB5
R473 4.7k
LCD-DB6
R474 4.7k
LCD-DB1
VH
LCD-DB2
VOL-CHECK
LCD-E
R476 2.2k
LCD-RW
R477 2.2k
C838 0.01
SYSTEM CONTROLLER
VSS
LCD-DB5
IC801
MB90483BPF-G
-153E1
KEY0
C840
0.01
R851 1k
KEY0
R849 1k
KEY2
R850 1k
KEY1
KEY2
KEY1
LCD-RES
NC
LCD-RW
AVSS
LCD-E
AVRH
CN801
23P
DATA
C837
0.01
C856 1
R478 2.2k
LCD-RS
EEPROM-SEL
NC
JOG-A
NC
KEY1
BACKUP-ON
R-CLOCK
L-OUT
C860
22p
AGND
JC802
0
R-OUT
R-OUT
L807
47H
AVDD(3.3V)
XTACN
XRST
CLOK
KEY0
R806 10k
C874
220
10V
EXCEPT
TW,KR,AUS
C803
R802 10k
R801 10k
C833 100p
R855 10k
C832 100p
R856 10k
(TW,KR,AUS)
REQ
ACK
XLAT
XLAT
SENS
SENS
SCOR
ODATA2
Q809
RT1N144M
DATA2
XLAT2
SCOR
R805 10k
R803 10k
C806
0.1
C802
0.01
FB802
ACK
(SP,TW,KR,TH,AUS)
(US,CND,E,MX)
Q804,806
IREQ
CLOK
REQ
Q811,812
DC LEVEL DETECT
LED
C801
0.1
B+ SWITCH
IREQ
XLAT2
R838 1k
R840 2.2k
R841 1k
R839 1k
R837 1k
R836 1k
R835 1k
R834 1k
R833 1k
R832 100
R830 100
R878 100
R829 1k
R848 1k
R847 1k
C842
100p
R826 1k
Q803
2SC4154TP
R825 1k
OUT
IN
IC802
XC6202-33
DRIVE
D-GND2
Q811
RT1N151M-TP-1
Q810
RT1P144M
IDATA2
+3.3V REGULATOR
DGND
L-OUT
XTACN
R816
4.7k
GND
R817
4.7k
D-OUT
R-MUTE
R-CE
R-COUNT
R-DATA
TU-ON
CD3.3V-ON
VCC5
CLOK
A-MUTE
P-CON
DATA
TESTA
TESTB
SENS
SHIMUKE2
SHIMUKE3
MEGABASS
SHIMUKE1
NC
NC
NC
NC
NC
NC
C859
22p
R842 1k
C845
47p
Q806
RT1N144M
KEY0
DVDD(3.3V)
Q812
RT1P151M-TP-1
XRST
Q804
RT1P144M
VDD(SW)
M-MUTE
R845
47k
VM-CONT
DATA
CLOK2
M-MUTE
FB804
L801
10H
CN806
11P
FB801
CLOK2
KEY1
RMC-VCC
CN804
4P
100p
BL-CONT
100p
KEY2
C422
R488 10k
KEY2
C421
JOG-B
EEP-SDA
EEP-SCL
BL
JOG-A
VOL-DATA
JOG-B
VSS
R815 4.7k
VOL-CLK
REMOTE
C839
0.01
FB803
R846
10k
R480 1k
R481 1k
R812
220k
AVCC
LCD-RES
D-GND
R813
220k
C855 1
R479 4.7k
LCD-3.3V
R887 220k
R859 0
3.3V-CHECK
LCD-DB4
LCD-DB7
LCD-RS
R888 220k
JC806
0
R862 1k
LCD-DB6
R475 4.7k
C868 0.01
R811 10k
LCD-DB3
LCD-DB7
C870 10 50V
R899 10k
C831 1
SHIFT CLOCK
R886 220k
MD1
X0
R882 4.7k
C841
0.01
R883 4.7k
R854
10k
R884 4.7k
WP
MD2
XLAT
AC-IN
CD-DOOR
IREQ
SCOR
IDATA2
XLAT2
CLOK2
ODATA2
NC
REQ
ACK
REMOTE
XRST
XTACN
M-MUTE
NC
NC
LOAD
NC
NC
NC
NC
VSS
R853
10k
X801 4.19MHz
C830
10p
Q801,802
X1A
JC801
0
C829
22p
RESET
C827
220p
VH-CONT
470p
470p
470p
C425
C424
C423
470p
470p
470p
C428
C427
C426
470p
470p
470p
C431
C430
C429
470p
100p
470p
C434
C433
BL 6V
C432
CN807
11P
X0A
C828
47p
Q802
2SC4154TP
SHIFT
C867 1000p
MD-GND
CD-6.0V
L806
Q809,810
47 6.3V(US,CND,E,MX)
C805
100p
47 10V(SP,TW,KR,TH,AUS)
CD-6.0V
B+ SWITCH
MD-GND
D-GND1
R844
22k
VOL-CHK
SENS
L-OUT
CD-L
C854
100p
L802
0.22H
C810 100p
TP03
TP02
C861 100p
TU-L
TU-R
C862 100p
R-VT
C853 100p
C851 100p
CLOK
DATA
C850 470p
R-VT
R486 2.2k
A-GND
R485 2.2k
TU-R
R484 2.2k
RADIO 6V
R483 2.2k
GND
SCL
TU-L
R-CE
A2
WP
R-DATA
A1
VDD
R818
22k
S-GND
C852
100p
C849 1000p
SDA
IC804
BR24L16
CD-R
MUTING
C848 0.01
EEPROM
R-OUT
C875
220p
Q808
RT1N144M
R-CLOCK
A0
R-COUNT
R-MUTE
VDD(SW)
CD3.3V-ON
AC-HI
P-CON
BATT-COM
A-MUTE
CD 3.3V
V-CLK
V-DATA
MEGA BASS
A-GND
U-COM3.3V
BACKUP-ON
S-GND
+B
D-GND2
AU-6.0V
1 CN802
11P
ZS-SN10
22
22
ZS-SN10
Ver. 1.3
See page 27 for IC Block Diagrams.
5-11. SCHEMATIC DIAGRAM MAIN SECTION (2/2)
(2/2)
R110
10k
R111
1k
CN302
3P
R106
47k
LINE-L
A-GND
LINE-R
CN303
3P
C119
1000p
LINE-L
A-GND
LINE-R
L301 1H
C206 1000p
C204 4.7
C107 1000p
R114
2.2k
0.0022
C112
0.0047
R118
0
R115
1k
R117
470
C207 1000p
C104
4.7 50V
Q101
2SC4154TP
C304
47
10V
R119 4.7k
R324 1M
R102 2.2k
D301
KDS121-RTK
POWER AMP
R220 47k
GND
FILTER
SC
LI-L
VCC
SI
RA-L
LI-R
LCH
RA-R
BOR
RCH
CD-R
CD-L
BNFR
SEL L
BNFL
BOL
L IN
SEL R
TNFL
C216
2200p
R202
2.2k
IC304
BA5417
R219
4.7k
Q201
2SC4154TP
Q101,201
R214
2.2k
R215
1k
R217
470
MEGA BASS CONTROL
FILTER
POWER
GND
C324
0.22
C213
0.0022
L804
47H
INPUT SELECT,
R221 4.7k
ELECTRICAL
R113
470k
VOLUME,
R213
470k
R225
4.7k
R216
220
C211
4.7
50V
SURROUND/
TONE
R-VT
R112
4.7k
C220
100p
0.01
C210 0.1
C301
100
10V
R212
4.7k
C306
100p
R301
100
C305
100p
R302
100
Q121
DTC143TUA
Q221
DTC143TUA
R123
470
Q121,221
R122
220
R222
220
C123
47 C122
1000p
10V
C223
47
10V
C222
1000p
C322
47
10V
CN322
4P
R226 100
FB201
R126 100
FB101
J301
C126
1000
10V
FB301
R223
470
C120
100p
C124
100
10V
C225
0.1
C125
0.1
R224
2.2
R124
2.2
MUTING
C302
C209 0.1
C110 0.1
2200p
C303
0.47
50V
C108
TU-R
CD-6.0V
2200p
TU-L
C208
CD-R
C109 0.1
IC301
BD3870FS
CN301
4P
C212
0.0047
CONTROL
CD-L
R323
10k
R218
0
C224
100 10V
50V
C202 2.2
R101 10k
R201 10k
50V
50V
C101 2.2
C201 2.2
C325
10
50V
R309
10k
C111
4.7
50V
C102 2.2
50V
CAP
TNFR
R IN
C116
2200p
R125 4.7k
50V
C113
BS L
C106 1000p
C218 1 50V
47H
NC
C118 1 50V
R116
220
VCC
C205 1000p
BSR
C105 1000p
C217 1 50V
STBY
C117 1 50V
L201
R211
1k
PREGND2
R210
10k
C103
0.47
50V
PREGND1
C203
0.47
50V
R205
10k
R120 47k
R105
10k
C114 1 50V
R203
2.2k
R121 4.7k
R204
1k
C214 1 50V
R103
2.2k
J322
LINE IN
C219
1000p
R206
47k
R104
1k
L101 47H
R322
1k
C226
1000
10V
CN323
4P
L
SP101
(L-CH)
GND
C127
100p
R
SP201
(R-CH)
GND
MD-GND
R304
10k
D-GND1
R303
10k
C227
100p
VOL-CHK
R127
0
A-GND
C321
22
25V
R227
0
MEGA BASS
R305 1k
V-DATA
R306 1k
V-CLK
CD 3.3V
CN901
4P
R321 2.2k
CN905
4P
VDD
VDD
GND
GND
C906
10
50V
A-MUTE
C908
0.22
P-CON
AC-HI
AC-HI
CN903
3P
AC-HI
BATT-COM
BATT-COM
BATT-COM
BATT-COM
GND
CD3.3V-ON
BATT
VDD(SW)
C950
4700
16V
+B
JC808
0
AU-6.0V
T901
D902 1N4002B
R951 2.2k
R900
1k
R950 2.2k
R953 2.2k
BACKUP-ON
C902 0.022
Q952
KTA1273Y
R952 2.2k
+6V REGULATOR
U-COM3.3V
R902 1k
+3.3V REGULATOR
D901 1N4002B
J901
POWER TRNASFORMER
C960 0.01
S-GND
Q955
KTC3203-Y
R901 1k
Q956
2SB798
R903 1k
D-GND2
C901 0.022
C903 0.022
D903 1N4002B
D904 1N4002B
D908
ISS355-TE
C904 0.022
R956
47k
Q954
2SD2394-F
F902
T2AL 250V(SP,KR,TH,AUS)
+6V REGULATOR
R961 1k
R960 1k
R959 1k
R957
2.2k
Q951
RT1N436M-TP-1
Q951-953
Q953
2SC4154TP
B+ SWITCH
BATT-COM
CN904
2P
R955
10k
BATT-COM
D951
KDS120-RTK
D953 UDZSTE-176.8B
R954
10k
C953 220 10V
C961
C952 0.01
220 10V
0.01
C955
0.01
C907
D905 UDZSTE-6.8B
100 10V
100 10V
C956
C954
C957 0.1
IN
GND
ON/OFF
220 16V
R958
2.2k
C951
0.01
C963 10 50V
R858
47k
0.1
R800
470k
C958
R325
1k
IC901
S-816A33AMC
C959
C326
220
16V
+3.3V REGULATOR
EXT
D907
1SS355TE-17
B+ SWITCH
OUT
Q813
2SA1602TP
R326
1k
2.5A 125V(US,CND,E,MX,TW)
D906
ISS355TE-17
GND
BATT
CN902
4P
DRY BATTERY
SIZE"C"
6PCS. 9V
ZS-SN10
23
23
ZS-SN10
5-12. PRINTED WIRING BOARDS PANEL SECTION
10
11
12
13
14
15
LCD BOARD
B
REPEAT
MODE
DISPLAY
LINE
R453
S425
S410
S424
R458
S423
S422
R494
R454
R452
R451
R459
SEARCH
S418
R450
R438
u
D402
(LCD BACK LIGHT)
JW402
/ TUNE
1
R401
C420
R416
C405
R402
/ TUNE
+
R415
C419
S420
1
S401
ROTARY
ENCODER
(JOG)
C406
>
PRESET
+
.
PRESET
JW403
S421
R446
IC401
R447
S412
R449
R493
S413
R448
R437
R436
S419
R417
C402
S411
R491
R490
C418
R492
S414
22
C412
C414
C413
L401
C408
C409
C407
C410
C403
C411
C401
ENTER/
MEMORY
C404
R439
RADIO/BAND
AUTO PRESET
C417
R440
LCD401
LIQUID CRYSTAL DISPLAY
11
L403
L402
1-866-323-
(11)
1-867-694-
(11)
S402 407,
S410 414,
S418 424
CN405
CN402
G
MAIN BOARD
CN807
(Page 20)
MAIN BOARD
CN806
(Page 20)
CONTROL (2)
CONTROL (1)
I
R430
S402
D401
OPR/BATT
S407
R426
R427
S403
CN403
POWER
MAIN BOARD
CN804
SOUND
(Page 20)
R431
S406
S404
S405
MEGA BASS
R428
R429
SLEEP
R421
R432
VOLUME
R420
CN404
CN401
R425
R419
R418
11
1-866-327-
11
(11)
ZS-SN10
24
24
ZS-SN10
Ver. 1.3
5-13. SCHEMATIC DIAGRAM PANEL SECTION
CN405
11P
(Page 22)
LCD401
(Page 22)
C403 1
C402 1
C418 47p
R492
10k
C404 1
C417 47p
C413 47p
C414 47p
C411 47p
C412 47p
C409 47p
C410 47p
C407 47p
C408 47p
R417 470k
L401
47H
C401
1
R490
2.2k
R491
0
L403
1H
L402
1H
CN402
11P
S401
*R459
ROTARY ENCODER(JOG)
R458
470
R459
*
220 (WHITE:US,CND)
470 (EXCEPT WHITE:US,CND)
GND
IC401
RPM7140
D402
*
R402
1k
R401
1k
(EXCEPT WHITE:US,CND)
SLR343EBT
(WHITE:US,CND)
SW 9V
C405
470p
C420
0.01
R416
100k
S410
S411
LINE
RADIO/BAND
S412
S413
/TUNE
/TUNE
R449
1k
R450
2.2k
R493
1k
S414
POWER
R418
470
R420
1k
R419
470
R421
1k
KEY0
D-GND2
S403
SLEEP
CN403
4P
D401
L-34HD
R425
220
OPR/BATT
R494
2.2k
S425
ENTER/
SEARCH
MEMORY
AUTO
PRESET
R446
220
R440
2.2k
R439
1k
S402
D-GND2
C406
0.01
C419
0.01
R438
1k
R427
470
D-GND2
(Page 22)
R437
470
R426
220
KEY0
R415
47k
(LCD BACK LIGHT)
R436
220
CN401
2P
*D402
SLI-343YC3F
R447
470
R448
1k
R451
2.2k
R452
1k
R453
2.2k
R454
4.7k
CN404
2P
KEY0
R428
1k
R429
1k
R430
2.2k
R431
1k
R432
2.2k
D-GND2
S418
S419
S420
S421
S422
REPEAT
PRESET +
S423
S424
MODE
S404
DISPLAY
VOLUME
PRESET
ZS-SN10
25
25
S405
VOLUME
S406
MEGA BASS
S407
SOUND
ZS-SN10
Ver. 1.3
Waveforms
IC Block Diagrams
3.3 Vp-p
22.8 s
0.9 Vp-p
30.5 s
13.3 s
1 V/DIV, 10 s/DIV
IC402 FAN8040G3
CH3RIN
GND
MUTE
POWVCC
CH3OUTF
CH3OUTR
CH4OUTF
CH4OUTR
IC801 ul (X1A)
CH3FIN
wa
CH4IN
IC2 w; (XOUT)
CH4CAPA
qa
OUTVREF
IC201 1 (LRCK)
(CD PLAY mode)
CD Board
MAIN Board
OPOUT
TUNER Board
PREVCC
CD Board
28
27
26
25
24
23
22
21
20
19
18
17
16
15
3.5 Vp-p
MUTING
1 V/DIV, 10 s/DIV
500 mV/DIV, 5 s/DIV
IC201 5 (BCK)
(CD PLAY mode)
ws
IC801 id (X1)
INTERFACE
LEVEL SHIFT
INTERFACE
3.3 Vp-p
472 ns
INTERFACE
3.7 Vp-p
239 ns
1 V/DIV, 200 ns/DIV
1 V/DIV, 100 ns/DIV

D
11
12
13
14
CH2OUTR
CH2OUTF
CH1OUTR
CH1OUTF
+
VREF
CH1FIN
CH1RIN
CH2FIN
CH2RIN
GND
VREFIN
10
POWVCC
1 2
SW
IC201 u; (RFACO)
(CD PLAY mode)
OPIN
OPIN+
0.5 to 1.1 Vp-p
200 mV/DIV, 500 ns/DIV
IC2 LC72137M-TLM-E
IC1 TA2149BN
IC201 <z/, (XTAO)

(CD PLAY mode)
RF GND 1
24 FM RFOUT
FM RF
23 RF VCC
FM RFIN 2
2.3 Vp-p
MIX OUT 4
22 AM RFIN
AM
MIX
AM LOW CUT 3
19 XIN
AM
OSC
AM IF IN 6
LEVEL
DET
1/8
FM IF IN 7
AM
DET
AGC
18 ST LED
SW
AF BUFF
IF REQ
B02
B03
I01
I02
MUTE
26
26
18 AOUT
17 AIN
16 PD
15 VSS
UNLOCK
DETECTOR
POWER ON
RESET
14 VDD
13 B04
AF
15 MPX IN
VCO
DIVIDE
14 LPF1
DECODE
13 LPF2
UNIVERSAL
COUNTER
IFIN 10
ZS-SN10
PHASE
DETECTOR
CHARGE
PUMP
17 IF REQ
ST/MO
FM/AM
R-OUT 11
12BITS
PROGRAMMABLE
DIVIDER
16 DET OUT
FM
DET
QUAD 10
L-OUT 12
19 OSC OUT
IF BUFF
FM IF
AGC 9
REFERENCE
DIVIDER
B01
1/1 OR
1/16
ST
GND 8
20 AM OSC
BUFF
BUFF
VCC 5
AM IF
CCB
I/F
21 FM OSC
59.4 ns
1 V/DIV, 20 ns/DIV
1
2
3
4
20 XOUT
FM
OSC
FM
MIX
CE
DI
CL
DO
DATA SHIFT REGISTER

LATCH
TUNER Board
SWALLOW
COUNTER
1/16,1/17
4BITS
1/2
12 FMIN
11 AMIN
ZS-SN10
MAIN Board
IC301 BD3870FS-E2
VOUT
VIN
IC901 S-816A33AMC-BAI-T2-G
REFERENCE
VOLTAGE
ERROR
AMP
SINK
DRIVER
OVERCURRENT
PROTECT
CIRCUIT
EXT
VSS
ON/OFF
SOURCE
POWER
SUPPLY
27
ZS-SN10
IC Pin Function Description

CD BOARD IC201 CXD3014-201R (CD DSP)
Pin No.
Pin Name
I/O
LRCK
L/R sampling clock signal output terminal
LRCKI
L/R sampling clock signal input terminal
PCMD
Serial data output terminal
PCMDI
Serial data input terminal
BCK
Bit clock signal output terminal
BCKI
Bit clock signal input terminal
XTACN
XRST
VSS
10
IREQ
Codec data request signal input from the system controller

CD serial data transfer clock signal input from the system controller
28
Description
Oscillation circuit on/off switch control signal input from the system controller
H: self-oscillation, L: oscillation stop
Reset signal input from the system controller L: reset
Ground terminal
11
CLOK
12
DATA2
I/O
13
XLAT2
Codec serial data latch pulse input from the system controller
14
REQ
Codec chip select signal input from the system controller
Codec serial data input/output with the system controller
15
ACK
Codec acknowledge signal input from the system controller
16
XLAT
CD serial data latch pulse input from the system controller
17
VDD
Power supply terminal (+2.5V)
18
SVSS
Ground terminal
19
SVDD
20
SENS
SENS signal output to the system controller
21
WFCK
Not used
22
XUGF
Not used
23
XPCK
Not used
24
GFS
Not used
25
C2PO
Not used
26
SCOR
Subcode sync (S0+S1) detection signal output to the system controller
27
VDD
28
COUT
Not used
29
SVSS
Ground terminal
30
SVDD
31
MIRR
Not used
32
DFCT
Not used
33
FOK
Not used
34
VSS
Ground terminal
35
VDD
36
VSS
Ground terminal
37
MIRR
Not used
38
MDP
Spindle motor servo control signal output terminal

Disc inner position detection signal input terminal
39
SSTP
40
IOVSS1
Ground terminal
41
SFDR
Sled servo drive signal (+) output to the coil/motor drive
42
SRDR
Sled servo drive signal () output to the coil/motor drive
43
TFDR
Tracking servo drive signal (+) output to the coil/motor drive
44
TRDR
Tracking servo drive signal () output to the coil/motor drive
45
FFDR
Focus setvo drive signal (+) output to the coil/motor drive
46
FRDR
Focus servo drive signal () output to the coil/motor drive
ZS-SN10
Pin No.
Pin Name
I/O
Description
47
IOVDD1
48
AVDD0
49
AVSS0
Ground terminal
50
E signal input from the optical pick-up block
51
F signal input from the optical pick-up block
52
TEI
Tracking error signal input terminal
53
TEO
Tracking error signal output terminal
54
FEI
Focus error signal input terminal
55
FEO
Focus error signal output terminal
56
VC
Middle point voltage output terminal
57
A signal iuput from the optical pick-up block
58
B signal input from the optical pick-up block
59
C signal iuput from the optical pick-up block
60
D signal input from the optical pick-up block
61
AVDD4
62
RFDCO
Not used
63
PDSENS
Not used
64
AC_SUM
RFAC summing amplifier signal output terminal
65
EQ_IN
RF equalizer circuit input terminal
66
LD
67
PD
Light amount monitor input from the optical pick-up block laser diode
Equalizer cut off frequency adjustment terminal
Laser diode on/off control signal output to the automatic power control circuit
L: laser off, H: laser on
68
RFC
69
AVSS4
Ground terminal
70
RFACO
EFM signal output terminal
71
RFACI
EFM signal input terminal
72
AVDD3
73
BIAS
Asymmetry circuit constant current input terminal
74
ASYI
Playback EFM asymmetry comparator voltage input terminal
75
ASYO
Playback EFM full-swing output terminal
76
VPCO
Charge pump output terminal for broad-band EFM PLL

VCO2 control voltage input terminal for broad-band EFM PLL
77
VCTL
78
AVSS3
79
CLTV
VCO1 control voltage input terminal for multiplier
80
FILO
Filter output terminal for master PLL
81
FILI
Filter input terminal for master PLL
Ground terminal
82
PCO
Charge pump output terminal for master PLL
83
SVSS
Ground terminal
84
SVDD
85
SRAMSTB
86
VDD
87
VSS
Ground terminal
88
TEST1
For test terminal
89
DATA
CD serial data input from the system controller
90
CLOK2
Codec serial data transfer clock signal input from the system controller
Codec standby on/off control signal input terminal Not used
Normally fixed at L
91
SVSS
Ground terminal
92
SVDD
93
JTAGTCK
Not used
94
JTAGTDI
Not used
29
ZS-SN10
Pin No.
Pin Name
I/O
95
JTAGTDO
Not used
96
JTAGTMS
Not used
97
TRST
Not used
30
Description
98
VSS
Ground terminal
99
VDD
100
IOVDD2
101
DOUT
Digital audio signal output terminal Not used
102
TEST
For test terminal
Normally fixed at L
Normally fixed at L
103
TES1
For test terminal
104
IOVSS2
Ground terminal
105
PLLVDD
106
PLLVSS
Ground terminal
107
XVSS
Ground terminal
108
XTAO
System clock output terminal (16.9344 MHz)
109
XTAI
System clock input terminal (16.9344 MHz)
110
XVDD
111
AVDD1
112
AOUT1
L-ch analog audio signal output terminal
113
VREFL
L-ch reference voltage output terminal
114
AVSS1
Ground terminal
115
AVSS2
Ground terminal
116
VREFR
R-ch reference voltage output terminal
117
AOUT2
R-ch analog audio signal output terminal
118
AVDD1
119
IOVDD0
120
IOVSS0
Ground terminal
ZS-SN10
Ver. 1.3
MAIN BOARD IC801 MB90483BPF-G-153E1 (SYSTEM CONTROLLER)

Pin No.
Pin Name
I/O
Description
1 to 6
NC
Not used
EEP-SCL
Serial clock signal output terminal to the EEPROM
EEP-SDA
I/O
VOL-DATA
Serial data output to the electrical volume
10
VOL-CLK
Serial data transfer clock signal output to the electrical volume

Ground terminal
Two-way serial data bus with the EEPROM
11
VSS
12 to 14
SIMUKE1 to SIMUKE3
For destination setting terminal
15
MEGABASS
MEGABASS on/off control signal output terminal
16
TESTA
For CD test setting terminal
17
TESTB
For LCD test setting terminal
Fixed at H in this set

Fixed at H in this set
18
SENS
Internal status (SENSE) signal input from the CD DSP
19
DATA
Serial data output to the CD DSP
20
CLOK
Serial data transfer clock signal output to the CD DSP
21
A-MUTE
Audio muting on/off control signal output terminal H: muting
22
P-CON
Power control signal output terminal H: active
23
VCC5
24
TU-ON
Tuner power on/off control signal output terminal H: tuner on
25
CD3.3V-ON
CD power on/off control signal output terminal
26
BACKUP-ON
CD power select signal output terminal for power off state L: power off state
27
R-COUNT
PLL serial count data input terminal
28
R-DATA
PLL serial data output terminal
29
R-CLOCK
PLL serial data transfer clock signal output terminal
30
R-CE
PLL chip enable signal output terminal
31
R-MUTE
Tuner muting on/off control signal output terminal
32
VM-CONT
Battery middle voltage (+4.5V) detection circuit control signal output terminal
33, 34
NC
Not used
35
AVCC
36
AVRH
37
AVSS
Ground terminal (for A/D converter)
38
NC
Not used
39
KEY1
Key input terminal (A/D input)
40
KEY2
41
KEY0
42
VSS
43
3.3V-CHECK
CD power voltage detection signal input terminal
44
VOL-CHECK
Electrical volume power voltage detection signal input terminal
45
VH
Battery high voltage (+9V) detection signal input terminal
46
VM
Battery middle voltage (+4.5V) detection signal input terminal
H: CD on
H: active
Power supply terminal (+3.3V) (for A/D converter)

Reference voltage input terminal (+3.3V) (for A/D converter)
Ground terminal
47, 48
P80, P81
Not used
49 to 51
MD0 to MD2
For mode setting terminal
52
WP
Key interruption processing start signal input terminal
53
CD DOOR
CD lid open/close detection switch input terminal L: CD lid is close
54
AC-IN
AC voltage detection signal input terminal
55
XLAT
Serial data latch pulse output to the CD DSP
56
SCOR
Subcode sync (S0+S1) detection signal input from the CD DSP
57
IREQ
Codec data request signal input from the CD DSP
58
IDATA2
Codec serial data input from the CD DSP
59
ODATA2
Codec serial data output to the CD DSP
L: AC in
31
ZS-SN10
Pin No.
Pin Name
I/O
Description
60
CLOK2
Codec serial data transfer clock signal output to the CD DSP
61
XLAT2
Codec serial data latch pulse output to the CD DSP
62
REQ
Codec data request signal output to the CD DSP
63
ACK
Codec acknowledge signal input from the CD DSP
64
REMOTE
Remote control signal input terminal
65
NC
Not used
66
M-MUTE
Muting on/off control signal output to the coil/motor drive H: active
67
XTACN
68
XRST
69
VH-CONT
Battery high voltage (+9V) detection circuit control signal output terminal
70
LOAD
Load control signal output for battery check state
71 to 76
NC
Not used
77
RESET
System reset signal input from the reset signal generator L: reset
78
SHIFT
Shift point terminal for oscillation frequency change
79
X1A
Sub system clock output terminal (32.768 kHz)
80
X0A
Sub system clock input terminal (32.768 kHz)
81
VSS
82
X0
Main system clock input terminal (4.19 MHz)
Oscillation circuit on/off switch control signal output to the CD DSP

H: self-oscillation, L: oscillation stop
System reset signal output to the CD DSP L: reset
Ground terminal
83
X1
Main system clock output terminal (4.19 MHz)
84
VCC3
85 to 92
LCD-DB0 to LCD-DB7
I/O
LCD parallel data input/output terminal
93
LCD-RES
LCD reset control signal output terminal L: reset
94
LCD-RW
LCD chip data read/write signal output terminal
95
LCD-E
LCD data enable signal output terminal
96
LCD-RS
LCD resistor select signal output terminal
97
EEPROM-SEL
EEPROM setting terminal Fixed at L in this set
98, 99
JOG-A, JOG-B
Jog dial pulse input from the rotary encoder (JOG)
100
BL
LCD back light on/off control signal output terminal H: back light on
32
ZS-SN10
Ver. 1.4
SECTION 6
EXPLODED VIEWS
NOTE:
-XX and -X mean standardized parts, so they
may have some difference from the original
one.
Items marked * are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
The mechanical parts with no reference
number in the exploded views are not supplied.
Accessories are given in the last of electrical
parts list.
6-1.
CABINET SECTION
Color Indication of Appearance Parts

Example:
KNOB, BALANCE (WHITE) . . . (RED)
R
R
Parts of Color Cabinets Color
Abbreviation
CND : Canadian model
KR
: Korean model
MX
: Mexican model
SP
: Singapore model
TH
: Thai model
TW
: Taiwan model
The components identified by mark 0 or

dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifis par une marque 0
sont critiques pour la scurit.
Ne les remplacer que par une pice portant le
numro spcifi.
6
8
12
13
ANT1
MAIN board
cabinet front section
13
10
13
3
cabinet top section
cabinet bottom
section
9
3
9
14
not
supplied
11
1
Ref. No.
1
1
1
2
3
Part No.
Description
2-582-114-01
2-582-114-11
2-582-114-21
3-040-916-01
3-254-144-01
LID, BATTERY (BLACK)

LID, BATTERY (WHITE)
LID, BATTERY (SILVER)
FOOT (FRONT), RUBBER
SCREW (B3), (+) BV TAPPING
(for WHITE, SILVER)
3
4
5
5
6
3-254-144-11
3-252-833-01
2-582-130-01
2-582-130-21
1-831-915-11
3-252-827-01 SCREW (B2.6), (+) BV TAPPING
Remark
SCREW (B3), (+) BV TAPPING (for BLACK)

SCREW (M3), (+) P
WINDOW, LCD (for BLACK, WHITE)
WINDOW, LCD (for SILVER)
CABLE, FLEXIBLE FLAT (4 CORE)
Ref. No.
Part No.
Description
Remark
8
8
8
9
A-1105-346-A
A-1105-348-A
A-1105-349-A
2-024-906-01
MAIN BOARD, COMPLETE (US, CND, E, MX)

MAIN BOARD, COMPLETE (SP, TH)
MAIN BOARD, COMPLETE (TW, KR, AUS)
CUSHION (REAR)
10
11
11
12
13
3-018-963-01
3-577-414-01
3-577-414-11
2-594-013-01
3-254-144-01
CUSHION (BATTERY CASE LID)

SPACER (for BLACK)
SPACER (for WHITE, SILVER)
PLATE (MAIN), SHIELD
14
14
ANT1
4-017-441-01 CUSHION (B) (for BLACK)

4-017-441-31 CUSHION (B) (for WHITE, SILVER)
1-754-241-11 ANTENNA, TELESCOPIC
33
ZS-SN10
Ver. 1.4
6-2.
CABINET FRONT SECTION
69
68
54
61
57
LCD board
59
IC401
54
60
LCD401
58
63
not
supplied
64
62
64
56
65
66
55
66
51
not
supplied
not
supplied
53
54
65
66
SP101
67
55
73
70
71
66
not
supplied
70
(for SILVER)
66
68
69
70 68
66
SP201
52
72
Ref. No.
Part No.
Description
51
52
52
52
52
2-582-140-01
X-2050-833-1
X-2050-834-1
X-2050-835-1
X-2050-836-1
BOX (R), SPEAKER

CABI (FRONT) SUB ASSY (BLACK) (US)
CABI (FRONT) SUB ASSY (WHITE) (US)
CABI (FRONT) SUB ASSY (BLACK) (CND)
CABI (FRONT) SUB ASSY (WHITE) (CND)
52
52
53
53
53
X-2050-837-1 CABI (FRONT) SUB ASSY (SILVER)

(EXCEPT US)
X-2109-390-1 CABINET (FRONT) SUB ASSY (SILVER) (US)
2-582-115-01 BUTTON (CD) (BLACK)
2-582-115-11 BUTTON (CD) (WHITE)
2-582-115-21 BUTTON (CD) (SILVER)
54
55
56
57
57
3-254-151-01
3-254-143-01
2-582-139-01
A-1105-337-A
A-1124-479-A
SCREW (B2.6), (+) P TAPPING

BOX (L), SPEAKER
LCD BOARD, COMPLETE (for BLACK, SILVER)
LCD BOARD, COMPLETE (for WHITE)
58
59
60
61
62
2-582-131-01
2-582-138-03
2-582-152-01
3-252-827-01
2-582-133-01
HOLDER (LCD)
PLATE, LIGHT GUIDE
ILLUMINATOR
SCREW (B2.6), (+) BV TAPPING
HOLDER (JOG)
34
Remark
Ref. No.
Part No.
Description
63
63
63
64
65
2-582-127-01
2-582-127-11
2-582-127-21
1-831-926-11
3-254-144-01
KNOB (JOG) (BLACK)

KNOB (JOG) (WHITE)
KNOB (JOG) (SILVER)
66
67
68
69
70
2-024-906-01
2-633-236-01
3-357-572-01
3-885-228-01
4-942-511-01
CUSHION (REAR)
CUSHION (TUNER FFC)
CUSHION
CUSHION (B)
SPACER
71
71
71
72
X-2059-969-1
X-2059-970-1
2-582-132-01
2-582-150-01
PANEL SUB ASSY (for BLACK)

PANEL SUB ASSY (for WHITE)
PANEL (for SILVER)
SHEET (LCD WINDOW), ADHESIVE
73
2-178-844-01 WASHER (CD CHASSIS)
IC401
LCD401
SP101
SP201
6-701-681-01
1-479-194-11
1-826-212-11
1-826-212-11
Remark
(for SILVER)
IC RPM7140-V4
ELEMENT UNIT, LIQUID CRYSTAL
SPEAKER (10cm) (L-ch)
SPEAKER (10cm) (R-ch)
ZS-SN10
6-3.
CABINET TOP SECTION-1

109
108
107
106
not
supplied
115
105
110
114
cabinet top section-2
111
116
112
113
104
102
103
113
103
116
101
103
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
2-591-496-21
2-582-113-01
2-582-113-11
2-582-113-21
3-019-395-01
COVER (HANDLE) (SILVER)

HANDLE (BLACK)
HANDLE (WHITE)
HANDLE (SILVER)
PLATE, CHUCKING
101
101
101
102
103
2-582-129-01
2-582-129-11
2-582-129-21
3-047-468-11
3-252-827-01
HANDLE (R), HOLDER (BLACK)

HANDLE (R), HOLDER (WHITE)
HANDLE (R), HOLDER (SILVER)
DAMPER
108
109
109
109
110
104
104
104
105
106
2-582-128-01
2-582-128-11
2-582-128-21
1-452-899-11
2-582-110-11
HANDLE (L), HOLDER (BLACK)

HANDLE (L), HOLDER (WHITE)
HANDLE (L), HOLDER (SILVER)
MAGNET
LID, CD (SILVER)
111
112
113
114
114
3-253-143-01
2-582-142-02
2-592-833-01
2-634-609-01
2-634-609-11

SPRING (CD)
CUSHION
COVER (SCREW) (for BLACK)
COVER (SCREW) (for WHITE)
106
106
107
108
108
2-582-110-21
2-582-110-31
3-254-151-01
2-591-496-01
2-591-496-11
LID, CD (BLACK)
LID, CD (WHITE)
COVER (HANDLE) (BLACK)
COVER (HANDLE) (WHITE)
114
115
116
116
2-634-609-21
4-942-511-01
4-942-511-01
4-942-511-11
COVER (SCREW) (for SILVER)

SPACER
SPACER (BLACK)
SPACER (WHITE, SILVER)
Remark
35
ZS-SN10
Ver. 1.4
6-4.
CABINET TOP SECTION-2
S801
155
not supplied
156
164
165
157
166
optical pick-up section
158
157
154
168
167
158
168
153
159
160
159
152
163
151
S201
151
161
162
Ref. No.
Part No.
Description
151
152
153
154
155
3-252-827-01
A-1105-376-A
A-1105-375-A
2-582-134-01
X-2050-819-1
SCREW (B2.6), (+) BV TAPP

CONTROL (2) BOARD, COMPLETE
CONTROL (1) BOARD, COMPLETE
HOLDER (LED)
CABINET TOP SUB ASSY (BLACK) (US)
Remark
155
155
155
155
X-2050-820-1
X-2050-821-1
X-2050-822-1
X-2050-823-1
155
CABINET TOP SUB ASSY (WHITE) (US)

CABINET TOP SUB ASSY (BLACK) (CND)
CABINET TOP SUB ASSY (WHITE) (CND)
CABINET TOP SUB ASSY (SILVER)
(EXCEPT US)
X-2109-392-1 CABINET (UPPER) SUB ASSY (SILVER) (US)
156
157
158
3-923-736-01 COVER, CD
3-931-379-21 RUBBER, VIBRATION PROOF (RED)
3-931-379-31 RUBBER, VIBRATION PROOF (GREEN)
36
Ref. No.
Part No.
Description
Remark
159
160
3-252-828-01 SCREW (B2.6), (+) PWH TAPPING

1-828-377-51 WIRE (FLAT TYPE) (23 CORE)
161
162
163
164
165
A-1107-453-A
3-245-709-51
1-832-404-21
3-015-345-21
3-255-320-01
CD BOARD, COMPLETE
SCREW
WIRE (FLAT TYPE) (16 CORE)
CUSHION
CUSHION, CR
166
167
168
S201
S801
3-018-963-01
3-357-572-01
3-885-228-01
1-771-853-11
1-692-960-21

CUSHION
CUSHION (B)
SWITCH, DETECTION (LIMIT)
SWITCH, PUSH (1 KEY)
ZS-SN10
Ver. 1.4
6-5.
CABINET BOTTOM SECTION
206
J901
215
not
supplied
T901
F902
209
L3
207
TUNER board
210
215
208
214
214
not
supplied
not
supplied
not
supplied
215
205
214
not
supplied
212
211
216
203
204
202
202
201
213
213
Ref. No.
Part No.
Description
Remark
* 201
202
* 203
204
205
1-866-326-11
3-240-561-02
1-866-325-11
A-1105-328-A
3-252-827-01
BATTERY2 BOARD
TERMINAL (), BATTERY
BATTERY1 BOARD
H/P BOARD, COMPLETE
206
207
208
209
209
3-254-143-01
A-1105-360-A
1-827-720-51
A-1105-354-A
A-1105-355-A

POWER BOARD, COMPLETE
TUNER BOARD, COMPLETE (US, CND, E, MX)
TUNER BOARD, COMPLETE
210
211
212
212
212
2-582-141-01
2-582-153-01
2-582-109-02
2-582-109-12
2-582-109-22
TERMINAL, ANTENNA
SHEET, BATTERY
CABINET (BOTTOM) (BLACK) (US)
CABINET (BOTTOM) (WHITE) (US)
CABINET (BOTTOM) (BLACK) (CND)
212
212
2-582-109-32 CABINET (BOTTOM) (WHITE) (CND)

2-582-109-42 CABINET (BOTTOM) (SILVER)
(EXCEPT US, CND)
Ref. No.
212
212
213
Part No.
Description
Remark
2-582-109-62 CABINET (BOTTOM) (SILVER) (US)

2-582-109-72 CABINET (BOTTOM) (SILVER) (CND)
3-252-830-01 SCREW (B3), (+) PWH TAPPING
214
215
216
216
0 F902
3-018-963-01
3-357-572-01
4-942-511-01
4-942-511-11
1-533-450-12

CUSHION
SPACER (for BLACK)
SPACER (for WHITE, SILVER)
FUSE, GLASS TUBE (DIA. 5) (2.5A/125V)
(US, CND, E, MX, TW)
0 F902
0 J901
0 J901
0 J901
L3
1-533-468-12 FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)

(SP, KR, TH, AUS)
1-526-818-11 INLET, AC (E, MX)
1-526-838-11 INLET, AC 2P (SP, TW, KR, TH, AUS)
1-540-009-11 INLET, AC (US, CND)
1-754-117-12 ANTENNA, FERRITE-ROD (MW)
0 T901
0 T901
1-435-917-22 TRANSFORMER, POWER (US, CND, E, MX, TW)

1-435-918-22 TRANSFORMER, POWER (SP, KR, TH, AUS)
37
ZS-SN10
6-6.
OPTICAL PICK-UP SECTION (KSM-213CDP)
506
not supplied
501
504
502
505
503
not supplied
(M401 (SPINDLE))
M402
Ref. No.
0 501
502
503
504
505
38
Part No.
8-848-483-12
2-174-500-01
2-626-908-01
2-627-003-01
X-2162-709-2
Description
Remark
OPTICAL PICK-UP (KSS-213C/C2RP1)
SCREW (2X3)
SHAFT, SLED
GEAR (B) (RP)
CHASSIS ASSY (CDP), MOTOR
(including M401 (SPINDLE))
Ref. No.
506
M402
Part No.
Description
Remark
2-626-907-11 GEAR (A)

X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)
ZS-SN10
SECTION 7
ELECTRICAL PARTS LIST
NOTE:
Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
-XX and -X mean standardized parts, so they
may have some difference from the original
one.
Items marked * are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
CAPACITORS
uF: F
COILS
uH: H
Ref. No.
Part No.
1-866-325-11 BATTERY1 BOARD

***************
RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
SEMICONDUCTORS
In each case, u: , for example:
uA. . : A. .,
uPA. . : PA. .,
uPB. . : PB. .,
uPC. . : PC. .,
uPD. . : PD. .
Abbreviation
AUS : Australian model.
CND : Canadian model.
KR
: Korean model.
MX
: Mexican model.
Description
Remark
3-240-561-02 TERMINAL (), BATTERY

************************************************************
1-866-326-11 BATTERY2 BOARD
***************
Ref. No.
Part No.
BATTERY1
Ver. 1.1
BATTERY2 CD
When indicating parts by reference number,

please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifis par une marque 0
sont critiques pour la scurit.
Ne les remplacer que par une pice portant le
numro spcifi.
SP
: Singapore model.
TH
: Thai model.
TW
: Taiwan model.
Description
Remark
C218
C219
C220
1-164-360-11 CERAMIC CHIP

0.1uF
0.1uF
100PF
C221
C222
C223
C224
C226
1-164-360-11
1-164-360-11
1-162-923-11
1-164-360-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
47PF
0.1uF
1uF
C227
C230
C232
C251
C252
1-165-908-11
1-162-927-11
1-164-360-11
1-164-315-11
1-162-968-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
100PF
0.1uF
470PF
0.0047uF
10%
5%
5%
10%
10V
50V
16V
50V
50V
C253
C254
C256
C257
C258
1-164-315-11
1-162-968-11
1-107-826-11
1-107-826-11
1-164-230-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
0.0047uF
0.1uF
0.1uF
220PF
5%
10%
10%
10%
5%
50V
50V
16V
16V
50V
C259
C260
C261
C264
C265
1-162-927-11
1-117-863-11
1-162-970-11
1-162-964-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.47uF
0.01uF
0.001uF
0.1uF
5%
10%
10%
10%
10%
50V
6.3V
25V
50V
16V
C267
C268
C269
C270
C271
1-162-919-11
1-162-919-11
1-126-208-21
1-126-208-21
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
22PF
22PF
47uF
47uF
0.1uF
5%
5%
20%
20%
10%
50V
50V
4V
4V
16V
C272
C273
C275
C291
C292
1-164-360-11
1-164-315-11
1-162-910-11
1-164-315-11
1-164-315-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
470PF
5PF
470PF
470PF
5%
0.25PF
5%
5%
16V
50V
50V
50V
50V
C301
C302
C303
C321
C322
1-164-360-11
1-137-710-11
1-137-710-11
1-162-964-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
10uF
0.001uF
1uF
C323
C401
C404
C405
C406
1-128-995-21
1-128-396-11
1-164-360-11
1-164-360-11
1-164-360-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
470uF
0.1uF
0.1uF
0.1uF
C424
0.1uF
5%
5%
10%
16V
16V
50V
16V
16V
50V
16V
10V
3-240-561-02 TERMINAL (), BATTERY

< CONNECTOR >
CN904 1-815-550-11 PIN, CONNECTOR (PWB) 2P
************************************************************
A-1107-453-A CD BOARD, COMPLETE
*******************
< CAPACITOR >
C101
C102
C103
C104
C105
1-162-919-11
1-162-919-11
1-162-927-11
1-164-230-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
22PF
100PF
220PF
100PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C107
C108
C109
C110
C111
1-164-230-11
1-164-230-11
1-164-230-11
1-164-230-11
1-164-230-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
220PF
220PF
220PF
220PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C112
C113
C132
C133
C201
1-162-927-11
1-162-927-11
1-162-919-11
1-162-927-11
1-128-995-21
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
100PF
100PF
22PF
100PF
100uF
5%
5%
5%
5%
20%
50V
50V
50V
50V
10V
C202
C203
C204
C205
C206
1-164-360-11
1-128-995-21
1-162-927-11
1-164-360-11
1-164-360-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
100PF
0.1uF
0.1uF
C207
C208
C210
C213
C214
1-128-995-21
1-164-360-11
1-164-360-11
1-164-360-11
1-164-360-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.1uF
0.1uF
0.1uF
C215
C217

0.1uF
0.1uF
20%
5%
20%
16V
10V
50V
16V
16V
10V
16V
16V
16V
16V
16V
16V
20%
20%
10%
20%
20%
16V
6.3V
6.3V
50V
10V
10V
10V
16V
16V
16V
16V
39
ZS-SN10
Ver. 1.3
CD CONTROL (1)
Ref. No.
C451
Part No.
CONTROL (2)
Description
Remark
0.047uF
10%
16V
< CONNECTOR >

CN102
CN301
1-770-706-21 CONNECTOR, FFC/FPC 23P

< IC >
IC201
IC202
IC402
8-753-239-32 IC CXD3014-201R
6-708-165-01 IC TK73325WTL-G
6-708-516-01 IC FAN8040G3
Ref. No.
Part No.
6-551-120-01 TRANSISTOR
Remark
1-216-789-11 METAL CHIP

1-216-864-11 SHORT CHIP
1-216-845-11 METAL CHIP
2.2
0
100K
R325
R326
R401
R421
R423
1-216-864-11
1-216-864-11
1-216-295-91
1-216-864-11
1-216-833-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
R451
R452
1-216-837-11 METAL CHIP

1-216-833-11 METAL CHIP
< TRANSISTOR >

Q321
Description
R322
R323
R324
5%
1/10W
5%
1/10W
0
0
0
0
10K
5%
1/10W
22K
10K
5%
5%
1/10W
1/10W
< VIBRATOR >

2SA2119K
X202
1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)
************************************************************
< RESISTOR >

R101
R102
R103
R104
R105
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R107
R108
R109
R110
R111
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R112
R113
R115
R201
R202
1-216-809-11
1-216-809-11
1-216-864-11
1-216-295-91
1-216-295-91
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
100
100
0
0
0
5%
5%
1/10W
1/10W
R203
R207
R249
R250
R252
1-216-295-91
1-216-295-91
1-216-841-11
1-216-857-11
1-216-833-11
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
47K
1M
10K
5%
5%
5%
1/10W
1/10W
1/10W
R253
R254
R255
R256
R257
1-216-821-11
1-216-833-11
1-216-821-11
1-216-837-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
1K
22K
470K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R258
R259
R260
R265
R266
1-216-849-11
1-216-833-11
1-216-864-11
1-216-829-11
1-216-821-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
220K
10K
0
4.7K
1K
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R267
R268
R270
R271
R275
1-216-829-11
1-216-833-11
1-216-817-11
1-216-857-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
10K
470
1M
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R276
R277
R278
R280
R291
1-216-841-11
1-216-809-11
1-216-809-11
1-216-864-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
47K
100
100
0
100
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R292
R321
1-216-809-11 METAL CHIP

1-216-789-11 METAL CHIP
100
2.2
5%
5%
1/10W
1/10W
A-1105-375-A CONTROL (1) BOARD, COMPLETE

***************************
< CONNECTOR >
CN401
CN403
1-815-550-11 PIN, CONNECTOR (PWB) 2P

1-784-726-11 CONNECTOR, FFC 4P
< LED >
D401
8-719-059-97 LED L-34HD (OPR/BATT)

< RESISTOR >
40
R418
R419
R420
R421
R425
1-216-817-11
1-216-817-11
1-216-821-11
1-216-821-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
470
1K
1K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R426
R427
1-216-813-11 METAL CHIP

1-216-817-11 METAL CHIP
220
470
5%
5%
1/10W
1/10W
< SWITCH >

S402
1-786-050-21 SWITCH, KEY BOARD (POWER)
S403
1-786-050-21 SWITCH, KEY BOARD (SLEEP)
************************************************************
A-1105-376-A CONTROL (2) BOARD, COMPLETE
***************************
< RESISTOR >
R428
R429
R430
R431
R432
1-216-821-11
1-216-821-11
1-216-825-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
2.2K
1K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< SWITCH >

S404
1-786-050-21 SWITCH, KEY BOARD (VOLUME +)
S405
1-786-050-21 SWITCH, KEY BOARD (VOLUME )
S406
1-786-050-21 SWITCH, KEY BOARD (MEGA BASS)
S407
1-786-050-21 SWITCH, KEY BOARD (SOUND)
************************************************************
ZS-SN10
H/P
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
A-1105-328-A H/P BOARD, COMPLETE

*******************

CN402
CN405
0.001uF
0.001uF
10%
10%

50V
50V
< LED >

D402
< CONNECTOR >

D402
* CN323
6-501-437-01 LED SLI-343YC3F (LCD BACK LIGHT)

(EXCEPT US (WHITE), CND (WHITE))
6-500-863-01 LED SLR343EBT (LCD BACK LIGHT)
(US (WHITE), CND (WHITE))
< FERRITE BEAD >

FB101
FB201
FB301
< IC >
1-469-701-21 FERRITE, EMI (SMD) (1608)

1-469-701-21 FERRITE, EMI (SMD) (1608)
1-469-701-21 FERRITE, EMI (SMD) (1608)
IC401
6-701-681-01 IC RPM7140-V4
< COIL >
< JACK >

J301
J322
Remark
< CONNECTOR >
< CAPACITOR >

C119
C219
Description
Ver. 1.3
LCD
L401
L402
L403
1-815-325-11 JACK (i)

1-566-891-11 JACK (LINE IN)
1-410-517-11 INDUCTOR
1-414-142-61 INDUCTOR
1-414-142-61 INDUCTOR
47uH
1uH
1uH
< LIQUID CRYSTAL DISPLAY >

< COIL >
LCD401 1-479-194-11 ELEMENT UNIT, LIQUID CRYSTAL I
L101
L201
L301
1-410-517-11 INDUCTOR
1-410-517-11 INDUCTOR
1-414-142-61 INDUCTOR
47uH
47uH
1uH
< RESISTOR >
< RESISTOR >

R126
1-216-809-11 METAL CHIP
100
5%
1/10W
R226
1-216-809-11 METAL CHIP
100
5%
1/10W
************************************************************
A-1105-337-A LCD BOARD, COMPLETE (for BLACK, SILVER)
A-1124-479-A LCD BOARD, COMPLETE (for WHITE)
********************
2-582-131-01 HOLDER, LCD
2-582-138-01 PLATE, LIGHT GUIDE
2-582-152-01 ILLUMINATOR
< CAPACITOR >
C401
C402
C403
C404
C405
1-115-156-11
1-115-156-11
1-115-156-11
1-115-156-11
1-162-962-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
1uF
1uF
470PF
10%
10V
10V
10V
10V
50V
C406
C407
C408
C409
C410
1-162-974-11
1-162-923-11
1-162-923-11
1-162-923-11
1-162-923-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
47PF
47PF
47PF
47PF
5%
5%
5%
5%
50V
50V
50V
50V
50V
C411
C412
C413
C414
C417
1-162-923-11
1-162-923-11
1-162-923-11
1-162-923-11
1-162-923-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47PF
47PF
47PF
47PF
47PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C418
C419
C420

47PF
0.01uF
0.01uF
5%
50V
50V
50V
R401
R402
R415
R416
R417
1-216-821-11
1-216-821-11
1-216-841-11
1-216-845-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
47K
100K
470K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R436
R437
R438
R439
R440
1-216-813-11
1-216-817-11
1-216-821-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
470
1K
1K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R446
R447
R448
R449
R450
1-216-813-11
1-216-817-11
1-216-821-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
470
1K
1K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R451
R452
R453
R454
R458
1-216-825-11
1-216-821-11
1-216-825-11
1-216-829-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
1K
2.2K
4.7K
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R459
1-216-813-11 METAL CHIP
R459
1-216-817-11
R490
R491
R492
1-216-825-11
1-216-864-11
1-216-833-11
R493
R494
1-216-821-11 METAL CHIP

1-216-825-11 METAL CHIP
220
5%
1/10W
(US (WHITE), CND (WHITE))
METAL CHIP
470
5%
1/10W
(EXCEPT US (WHITE), CND (WHITE))
METAL CHIP
2.2K
5%
1/10W
SHORT CHIP
0
METAL CHIP
10K
5%
1/10W
1K
2.2K
5%
5%
1/10W
1/10W
< SWITCH >

S401
S410
S411
1-478-528-11 ENCODER (ROTARY) (JOG)

1-786-050-21 SWITCH, KEY BOARD (LINE)
1-786-050-21 SWITCH, KEY BOARD
(RADIO/BAND, AUTO PRESET)
41
ZS-SN10
Ver. 1.3
LCD MAIN
Ref. No.
Part No.
Description
Remark
Part No.
Description
C211
C212
C213
C214
C216
1-126-963-11
1-162-968-11
1-162-966-11
1-126-960-11
1-162-966-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
4.7uF
0.0047uF
0.0022uF
1uF
0.0022uF
20%
10%
10%
20%
10%
C217
C218
C220
C222
C223
1-126-960-11
1-126-960-11
1-162-927-11
1-162-964-11
1-126-785-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
1uF
1uF
100PF
0.001uF
47uF
20%
50V
20%
50V
5%
50V
10%
50V
20%
10V
(US, CND, E, MX)
C223
1-126-947-11 ELECT
A-1105-346-A MAIN BOARD, COMPLETE (US, CND, E, MX)

A-1105-348-A MAIN BOARD, COMPLETE (SP, TH)
A-1105-349-A MAIN BOARD, COMPLETE (TW, KR, AUS)
*********************
C224
C225
C226
C227
1-104-658-91
1-107-826-11
1-126-926-11
1-162-927-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
20%
35V
100uF
20%
10V
0.1uF
10%
16V
1000uF
20%
10V
100PF
5%
50V
2-594-013-01 PLATE (MAIN), SHIELD

3-253-143-01 SCREW (B2.6), (+) P TAPPING
C301
C302
C303
C304
C305
1-104-658-91
1-162-974-11
1-126-959-11
1-126-947-11
1-162-927-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
100uF
0.01uF
0.47uF
47uF
100PF
20%
20%
20%
5%
10V
50V
50V
35V
50V
C306
C321
C322
C324
C325
1-162-927-11
1-104-662-91
1-126-947-11
1-115-467-11
1-126-964-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
100PF
22uF
47uF
0.22uF
10uF
5%
20%
20%
10%
20%
50V
25V
35V
10V
50V
C326
C421
C422
C423
C424
1-126-934-11
1-162-927-11
1-162-927-11
1-162-962-11
1-162-962-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220uF
100PF
100PF
470PF
470PF
20%
5%
5%
10%
10%
16V
50V
50V
50V
50V
C425
C426
C427
C428
C429
1-162-962-11
1-162-962-11
1-162-962-11
1-162-962-11
1-162-962-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
470PF
470PF
470PF
470PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C430
C431
C432
C433
C434
1-162-962-11
1-162-962-11
1-162-962-11
1-162-927-11
1-162-962-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
470PF
470PF
100PF
470PF
10%
10%
10%
5%
10%
50V
50V
50V
50V
50V
C801
C802
C803

1-126-513-11 ELECT
0.1uF
0.01uF
47uF
C803
1-126-947-11 ELECT
C805
25V
50V
20%
6.3V
(US, CND, E, MX)
47uF
20%
35V
100PF
5%
50V
C806
C807
C808
C809
C810
1-164-156-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100PF
100PF
100PF
100PF
5%
5%
5%
5%
25V
50V
50V
50V
50V
C811
C812
C813
C814
C815
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
100PF
100PF
5%
5%
5%
5%
5%
50V
50V
50V50V
50V
S412
S413
1-786-050-21 SWITCH, KEY BOARD (FOLDER/TUNE )

1-786-050-21 SWITCH, KEY BOARD (FOLDER/TUNE +)
S414
S418
S419
S420
S421
1-786-050-21
1-786-050-21
1-786-050-21
1-786-050-21
1-786-050-21
SWITCH, KEY BOARD (ENTER/MEMORY)

SWITCH, KEY BOARD (u)
SWITCH, KEY BOARD (x)
SWITCH, KEY BOARD (> PRESET +)
SWITCH, KEY BOARD (. PRESET )
S422
1-786-050-21 SWITCH, KEY BOARD (REPEAT)
S423
1-786-050-21 SWITCH, KEY BOARD (MODE)
S424
1-786-050-21 SWITCH, KEY BOARD (DISPLAY)
S425
1-786-050-21 SWITCH, KEY BOARD (FOLDER SEARCH)
************************************************************
< CAPACITOR >

C101
C102
C103
C104
C105
1-126-961-11
1-126-961-11
1-126-959-11
1-126-963-11
1-162-964-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
2.2uF
2.2uF
0.47uF
4.7uF
0.001uF
20%
20%
20%
20%
10%
50V
50V
50V
50V
50V
C106
C107
C108
C109
C110
1-162-964-11
1-162-964-11
1-162-966-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.0022uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
50V
50V
16V
16V
C111
C112
C113
C114
C116
1-126-963-11
1-162-968-11
1-162-966-11
1-126-960-11
1-162-966-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
4.7uF
0.0047uF
0.0022uF
1uF
0.0022uF
20%
10%
10%
20%
10%
50V
50V
50V
50V
50V
C117
C118
C120
C122
C123
1-126-960-11
1-126-960-11
1-162-927-11
1-162-964-11
1-126-785-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
1uF
1uF
100PF
0.001uF
47uF
20%
50V
20%
50V
5%
50V
10%
50V
20%
10V
(US, CND, E, MX)
C123
1-126-947-11 ELECT
C124
C125
C126
C127
1-104-658-91
1-107-826-11
1-126-926-11
1-162-927-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
20%
35V
100uF
20%
10V
0.1uF
10%
16V
1000uF
20%
10V
100PF
5%
50V
C201
C202
C203
C204
C205
1-126-961-11
1-126-961-11
1-126-959-11
1-126-963-11
1-162-964-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
2.2uF
2.2uF
0.47uF
4.7uF
0.001uF
20%
20%
20%
20%
10%
50V
50V
50V
50V
50V
C206
C207
C208
C209
C210
1-162-964-11
1-162-964-11
1-162-966-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.0022uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
50V
50V
16V
16V
42
47uF
Ref. No.
Remark
50V
50V
50V
50V
50V
47uF
ZS-SN10
Ver. 1.3
MAIN
Ref. No.
Part No.
Description
Remark
C816
C817
C818

22PF
22PF
100PF
5%
5%
5%
50V
50V
50V
C819
C820
C821
C822
C823
1-162-927-11
1-162-974-11
1-162-974-11
1-162-974-11
1-162-919-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.01uF
0.01uF
0.01uF
22PF
5%
5%
50V
50V
50V
50V
50V
C824
C825
C826
C827
C828
1-162-915-11
1-164-230-11
1-162-923-11
1-164-230-11
1-162-923-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10PF
220PF
47PF
220PF
47PF
0.5PF
5%
5%
5%
5%
50V
50V
50V
50V
50V
C829
C830
C831
C832
C833
1-162-919-11
1-162-915-11
1-115-156-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
10PF
1uF
100PF
100PF
5%
0.5PF
50V
50V
10V
50V
50V
C837
C838
C839
C840
C841
1-162-974-11
1-162-974-11
1-162-974-11
1-162-974-11
1-162-974-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
C842
C845
C848
C849
C850
1-162-927-11
1-162-923-11
1-162-970-11
1-162-964-11
1-162-962-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
47PF
0.01uF
0.001uF
470PF
5%
5%
10%
10%
10%
50V
50V
25V
50V
50V
C851
C852
C853
C854
C855
1-162-927-11
1-162-927-11
1-162-927-11
1-162-927-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
100PF
1uF
5%
5%
5%
5%
50V
50V
50V
50V
10V
C856
C859
C860
C861
C862
1-115-156-11
1-162-919-11
1-162-919-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
22PF
22PF
100PF
100PF
C867
C868
C869
C870
C871
1-162-964-11
1-162-970-11
1-115-156-11
1-126-964-11
1-162-919-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.001uF
0.01uF
1uF
10uF
22PF
10%
10%
20%
5%
50V
25V
10V
50V
50V
C872
C873
C874
C875
C907
1-162-919-11
1-126-926-11
1-126-923-91
1-164-230-11
1-162-970-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
22PF
1000uF
220uF
220PF
0.01uF
5%
20%
20%
5%
10%
50V
10V
10V
50V
25V
C950
C951
C952
C953
C954
1-126-937-11
1-162-970-11
1-162-970-11
1-126-923-91
1-104-658-91
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
4700uF
0.01uF
0.01uF
220uF
100uF
20%
10%
10%
20%
20%
16V
25V
25V
10V
10V
C955
C956
C957
C958
C959
1-126-923-91
1-104-658-91
1-164-156-11
1-164-156-11
1-126-934-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
220uF
100uF
0.1uF
0.1uF
220uF
20%
20%
10V
10V
25V
25V
16V
5%
5%
50V
50V
50V
50V
50V
5%
5%
5%
5%
20%
10V
50V
50V
50V
50V
Ref. No.
C960
C961
C963
Part No.
Description

1-126-964-11 ELECT
Remark
0.01uF
0.01uF
10uF
10%
10%
20%
25V
25V
50V
< CONNECTOR >

CN301
CN302
CN801
CN802
CN804
1-815-445-11
1-815-444-11
1-779-291-11
1-568-830-11
1-784-765-11
PIN, CONNECTOR (PWB) 4P

PIN, CONNECTOR (PWB) 3P
CONNECTOR, FFC (LIF (NON-ZIF)) 23P
CONNECTOR 11P
CONNECTOR, FFC 4P
CN806
CN807
CN901
1-568-830-11 CONNECTOR 11P

1-568-830-11 CONNECTOR 11P
< DIODE >
D301
D801
D802
D905
D906
8-719-082-07
8-719-082-07
8-719-069-54
8-719-978-33
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
KDS121-RTK
KDS121-RTK
UDZSTE-175.1B
DTZ-TT11-6.8B
1SS355TE-17
D907
D908
D951
D953
8-719-988-61
8-719-988-61
8-719-083-93
8-719-978-33
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
KDS120-RTK
DTZ-TT11-6.8B
< FERRITE BEAD >

FB801
FB802
FB803
FB804
1-469-701-21
1-469-701-21
1-500-445-21
1-500-445-21
FERRITE, EMI (SMD) (1608)

< IC >
IC301
IC304
IC801
IC802
IC803
6-701-824-11
8-759-426-51
6-806-037-01
6-706-338-01
6-703-224-01
IC
IC
IC
IC
IC
BD3870FS-E2
BA5417
MB90483BPF-G-153E1
XC6202P332FR
S-80828CNNB-B8NT2G
IC804
IC901
6-704-004-01 IC BR24L16F-WE2
8-759-679-43 IC S-816A33AMC-BAI-T2-G
< JUMPER RESISTOR >
JC801
JC802
JC803
JC804
JC805
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC806
JC807
JC808
1-216-864-11 SHORT CHIP

1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
0
0
0
< COIL >

L801
L802
L803
L804
L806
1-410-509-11
1-414-137-31
1-414-142-61
1-410-517-11
1-414-142-61
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
L807
1-410-517-11 INDUCTOR
10uH
0.22uH
1uH
47uH
1uH
47uH
43
ZS-SN10
Ver. 1.3
MAIN
Ref. No.
Part No.
Description
Remark
< TRANSISTOR >

Q101
Q121
Q201
Q221
Q801
8-729-602-21
8-729-029-10
8-729-602-21
8-729-029-10
8-729-602-21
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC4154-F
DTC143TUA-T106
2SC4154-F
DTC143TUA-T106
2SC4154-F
Q802
Q803
Q804
Q805
Q806
8-729-602-21
8-729-602-21
8-729-028-76
8-729-028-99
8-729-028-99
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC4154-F
2SC4154-F
DTA114YUA-T106
DTC114YUA-T106
DTC114YUA-T106
Q807
Q808
Q809
Q810
Q811
8-729-602-36
8-729-028-99
8-729-028-99
8-729-028-76
6-551-420-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1602-F
DTC114YUA-T106
DTC114YUA-T106
DTA114YUA-T106
RT1N151M-TP-1
Q812
Q813
Q821
Q822
Q823
6-551-424-01
8-729-602-36
6-551-424-01
6-551-420-01
8-729-602-21
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
RT1P151M-TP-1
2SA1602-F
RT1P151M-TP-1
RT1N151M-TP-1
2SC4154-F
Q824
Q951
Q952
Q953
Q954
8-729-037-13
6-551-422-01
8-729-040-76
8-729-602-21
8-729-018-99
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
KTA1271Y
RT1N436M-TP-1
KTA1273-Y-AT
2SC4154-F
2SD2394-F
Q955
Q956
KTC3203Y-AT
2SB798-DL
< RESISTOR >

R101
R102
R103
R104
R105
1-216-833-11
1-216-825-11
1-216-825-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
2.2K
2.2K
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R106
R110
R111
R112
R113
1-216-841-11
1-216-833-11
1-216-821-11
1-216-829-11
1-216-853-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
10K
1K
4.7K
470K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R114
R115
R116
R117
R118
1-216-825-11
1-216-821-11
1-216-813-11
1-216-817-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
2.2K
1K
220
470
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R119
R120
R121
R122
R123
1-216-829-11
1-216-841-11
1-216-829-11
1-216-813-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47K
4.7K
220
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R124
R125
R127
R201
R202
1-216-789-11
1-216-829-11
1-216-864-11
1-216-833-11
1-216-825-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
2.2
4.7K
0
10K
2.2K
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R203
1-216-825-11 METAL CHIP
2.2K
5%
1/10W
44
Ref. No.
Part No.
Description
R204
R205
R206
R210
1-216-821-11
1-216-833-11
1-216-841-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
47K
10K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
Remark
R211
R212
R213
R214
R215
1-216-821-11
1-216-829-11
1-216-853-11
1-216-825-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
4.7K
470K
2.2K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R216
R217
R218
R219
R220
1-216-813-11
1-216-817-11
1-216-864-11
1-216-829-11
1-216-841-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
220
470
0
4.7K
47K
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R221
R222
R223
R224
R225
1-216-829-11
1-216-813-11
1-216-817-11
1-216-789-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
220
470
2.2
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R227
R301
R302
R303
R304
1-216-864-11
1-216-809-11
1-216-809-11
1-216-833-11
1-216-833-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100
100
10K
10K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R305
R306
R309
R321
R322
1-216-821-11
1-216-821-11
1-216-833-11
1-216-825-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10K
2.2K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R323
R324
R325
R326
R468
1-216-833-11
1-216-857-11
1-216-821-11
1-216-821-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1M
1K
1K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R469
R470
R471
R472
R473
1-216-829-11
1-216-829-11
1-216-829-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
4.7K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R474
R475
R476
R477
R478
1-216-829-11
1-216-829-11
1-216-825-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
2.2K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R479
R480
R481
R483
R484
1-216-829-11
1-216-821-11
1-216-821-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
1K
1K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R485
R486
R488
R495
R496
1-216-825-11
1-216-825-11
1-216-833-11
1-216-829-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
10K
4.7K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R497
R498
R499
1-216-845-11 METAL CHIP

1-216-797-11 METAL CHIP
1-216-813-11 METAL CHIP
100K
10
220
5%
5%
5%
1/10W
1/10W
1/10W
ZS-SN10
MAIN
Ref. No.
Part No.
Description
Remark
R800
R801
1-216-853-11 METAL CHIP

1-216-833-11 METAL CHIP
470K
10K
R802
1-216-833-11 METAL CHIP
10K
R803
R805
1-216-833-11 METAL CHIP

1-216-833-11 METAL CHIP
10K
10K
R806
1-216-833-11 METAL CHIP
10K
R807
1-216-817-11 METAL CHIP
470
R808
R811
R812
R813
R815
1-216-817-11
1-216-833-11
1-216-849-11
1-216-849-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
10K
220K
220K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R816
R817
R818
R825
R826
1-216-829-11
1-216-829-11
1-216-837-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
22K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R827
R828
R829
R830
R831
1-216-821-11
1-216-841-11
1-216-821-11
1-216-809-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
47K
1K
100
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R832
R833
R834
R835
R836
1-216-809-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R837
R838
R839
R840
R841
1-216-821-11
1-216-821-11
1-216-821-11
1-216-825-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
2.2K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R842
R844
R845
R846
R847
1-216-821-11
1-216-837-11
1-216-841-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
22K
47K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R848
R849
R850
R851
R852
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R853
R854
R855
R856
R858
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R859
R862
R863
R864
R865
1-216-864-11
1-216-821-11
1-216-833-11
1-216-841-11
1-216-845-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
1K
10K
47K
100K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R866
R867
1-216-833-11 METAL CHIP

1-216-853-11 METAL CHIP
10K
470K
5%
5%
1/10W
1/10W
Ref. No.
Part No.
Description
Ver. 1.2
POWER
Remark
5%
1/10W
5%
1/10W
(TW, KR, AUS)
R868
R869
R870
1-216-821-11 METAL CHIP

1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
1K
1K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
(EXCEPT TW, KR, AUS)
5%
1/10W
5%
1/10W
5%
1/10W
(US, CND, E, MX)
5%
1/10W
R871
R872
R873
R874
R875
1-216-821-11
1-216-821-11
1-216-813-11
1-216-813-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
220
220
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R876
R877
R878
R879
R880
1-216-821-11
1-216-821-11
1-216-809-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
100
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R881
R882
R883
R884
R886
1-216-821-11
1-216-829-11
1-216-829-11
1-216-829-11
1-216-849-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
4.7K
4.7K
4.7K
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R887
R888
R891
R892
R893
1-216-849-11
1-216-849-11
1-216-821-11
1-216-813-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220K
220K
1K
220
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R894
R895
R896
R899
R900
1-216-829-11
1-216-821-11
1-216-833-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
1K
10K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R901
R902
R903
R950
R951
1-216-821-11
1-216-821-11
1-216-821-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R952
R953
R954
R955
R956
1-216-825-11
1-216-825-11
1-216-833-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
10K
10K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R957
R958
R959
R960
R961
1-216-825-11
1-216-825-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< VIBRATOR >

X801
1-813-175-21 VIBRATOR, CERAMIC (4.19MHz)
X802
1-795-915-11 VIBRATOR, CRYSTAL (32.768kHz)
************************************************************
A-1105-360-A POWER BOARD, COMPLETE
**********************
1-533-233-31 FUSE HOLDER
< CAPACITOR >
C901
C902
C903

0.022uF
0.022uF
0.022uF
50V
50V
50V
45
ZS-SN10
Ver. 1.2
POWER
Ref. No.
TUNER
Part No.
Description
Remark
C904
C906

1-126-964-11 ELECT
0.022uF
10uF
C908
0.22uF
Part No.
Description
Remark

1-161-051-00 CERAMIC
22PF
10PF
0.01uF
5%
0.5PF
10%
50V
50V
25V
C51
C52
C53
C54
C55
1-162-919-11
1-162-915-11
1-137-190-91
1-126-923-91
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
FILM
ELECT
CERAMIC CHIP
22PF
10PF
0.22uF
220uF
100PF
5%
0.5PF
5%
20%
5%
50V
50V
50V
10V
50V
C56
C57
C59
C60
C61
1-162-964-11
1-162-964-11
1-162-927-11
1-162-964-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
100PF
0.001uF
100PF
10%
10%
5%
10%
5%
50V
50V
50V
50V
50V
A-1105-354-A TUNER BOARD, COMPLETE (US, CND, E, MX)

A-1105-355-A TUNER BOARD, COMPLETE
**********************
C62
C63
C65
C66
C68
1-162-927-11
1-162-927-11
1-126-963-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
4.7uF
100PF
100PF
5%
5%
20%
5%
5%
50V
50V
50V
50V
50V
2-582-141-01 TERMINAL, ANT
C77
< CAPACITOR >
C78
C80
C95

16V
< CONNECTOR >

CN903
Ref. No.
C43
C47
C49
20%
50V
50V

< DIODE >
D901
8-719-063-79 DIODE 1N4002B
D902
8-719-063-79 DIODE 1N4002B
D903
8-719-063-79 DIODE 1N4002B
D904
8-719-063-79 DIODE 1N4002B
************************************************************
C1
C4
C7
C8
C9
1-162-923-11
1-162-964-11
1-162-910-11
1-162-964-11
1-162-915-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47PF
0.001uF
5PF
0.001uF
10PF
C10
C11
C12
C13
1-126-960-11
1-107-826-11
1-126-963-11
1-162-970-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
1uF
0.1uF
4.7uF
0.01uF
C14
5%
10%
0.25PF
10%
0.5PF
50V
50V
50V
50V
50V
20%
50V
10%
16V
20%
50V
10%
25V
(US, CND, E, MX)
0.01uF
10%
25V
C14
C15
C15
C18
C20
1-126-923-91 ELECT
10%
25V
(US, CND, E, MX)
0.01uF
10%
25V
0.022uF 10%
25V
(US, CND, E, MX)
220uF
20%
10V
0.1uF
10%
16V
C21
C22
C23
C24
C26
1-126-960-11
1-107-826-11
1-126-960-11
1-162-960-11
1-162-927-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
1uF
220PF
100PF
20%
10%
20%
10%
5%
50V
16V
50V
50V
50V
C27
C29
C30
C31
C32
1-162-927-11
1-104-658-91
1-162-970-11
1-162-919-11
1-162-964-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100uF
0.01uF
22PF
0.001uF
5%
20%
10%
5%
10%
50V
10V
25V
50V
50V
C33
C34
C35
C37
C39
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.1uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
16V
C41
C42

220PF
100PF
5%
5%
50V
50V
46
0.022uF
0.0047uF 10%
50V
0.0047uF 10%
50V
0.01uF
10%
25V
0.001uF 10%
50V
< FILTER >

CF2
CF4
1-760-235-81 FILTER, CERAMIC

1-781-962-21 FILTER, CERAMIC
< CONNECTOR >
CNP1
1-568-854-11 CONNECTOR 11P

< TRIMMER >
CT1
CT3
1-141-442-91 CAP, CERAMIC TRIMMER

1-141-304-21 CAP, CERAMIC TRIMMER
< DIODE >
D1
D2
D3
D10
D11
8-719-078-48
8-719-078-48
8-719-050-69
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
KV1471ETR-G
KV1471ETR-G
KV1520N
1SS355TE-17
1SS355TE-17
< IC >
IC1
IC2
6-700-512-01 IC TA2149BN
8-759-483-40 IC LC72137M-TLM-E
< JUMPER RESISTOR >
JC1
JC2
JC3
JC4
JC5
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC6
JC11
JC12
JC13
JC24
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0 (SP, TW, KR, TH, AUS)
ZS-SN10
Ver. 1.3
TUNER
Ref. No.
JC33
JC34
Part No.
Description
1-216-864-11 SHORT CHIP

1-216-864-11 SHORT CHIP
Remark
Ref. No.
Description
Remark
MISCELLANEOUS
**************
0
0
6
64
105
160
163
< COIL >

L1
L2
L3
1-409-775-11 COIL, AIR-CORE

1-416-509-11 COIL, AIR-CORE
1-754-117-12 ANTENNA, FERRITE-ROD (MW)
L4
L11
L21
1-411-234-21 COIL, AM OSC

1-414-142-11 INDUCTOR
1-410-509-11 INDUCTOR
1uH (US, CND, E, MX)

10uH
208
0 501
505
ANT1
0 F902
< RESISTOR >

R1
R2
R3
R4
R5
1-216-817-11
1-216-817-11
1-216-833-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
470
10K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R10
R11
R13
R14
R24
1-216-805-11
1-216-825-11
1-216-821-11
1-216-821-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47
2.2K
1K
1K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R30
R31
R32
R33
R40
1-216-837-11
1-216-829-11
1-216-845-11
1-216-833-11
1-216-849-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
4.7K
100K
10K
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R41
R50
R51
R52
R53
1-216-833-11
1-216-821-11
1-216-833-11
1-216-864-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
10K
1K
10K
0
4.7K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R54
R55
R56
R57
R58
1-216-817-11
1-216-833-11
1-216-813-11
1-216-809-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
10K
220
100
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R59
R60
R61
R63
R65
1-216-825-11
1-216-825-11
1-216-825-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
2.2K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R91
R92
R94
1-216-813-11 METAL CHIP

1-216-813-11 METAL CHIP
1-216-821-11 METAL CHIP
220
220
1K
5%
5%
5%
1/10W
1/10W
1/10W
< TRANSFORMER >

T1
T2
Part No.
1-433-741-11 TRANSFORMER, IF
1-419-465-11 COIL (DET)
< VIBRATOR >
X1
1-795-449-11 VIBRATOR, CRYSTAL (75kHz)
************************************************************
0 F902
0 J901
0 J901
0 J901
M402
S201
S801
SP101
SP201
0 T901
1-831-915-11
1-831-926-11
1-452-899-11
1-828-377-51
1-832-404-21

MAGNET
1-827-720-51 WIRE (FLAT TYPE) (11 CORE)

8-848-483-12 OPTICAL PICK-UP (KSS-213C/C2RP1)
X-2162-709-2 CHASSIS ASSY (CDP), MOTOR
(including M401 (SPINDLE))
1-754-241-11 ANTENNA, TELESCOPIC
1-533-450-12 FUSE, GLASS TUBE (DIA. 5) (2.5A/125V)
(US, CND, E, MX, TW)
1-533-468-12 FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)
(SP, KR, TH, AUS)
1-526-818-11 INLET, AC (E, MX)
1-526-838-11 INLET, AC 2P (SP, TW, KR, TH, AUS)
1-540-009-11 INLET, AC (US, CND)
X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)
1-771-853-11 SWITCH, DETECTION (LIMIT)
1-692-960-21 SWITCH, PUSH (1 KEY)
1-826-212-11 SPEAKER (10cm) (L-ch)
1-826-212-11 SPEAKER (10cm) (R-ch)
1-435-917-22 TRANSFORMER, POWER (US, CND, E, MX, TW)
0 T901
1-435-918-22 TRANSFORMER, POWER (SP, KR, TH, AUS)
************************************************************
ACCESSORIES
***********
0
0
0
0
0
1-590-342-12
1-769-412-22
1-776-985-12
1-782-126-11
1-827-945-12
1-829-433-11 CORD, POWER (TW)

2-593-810-12 MANUAL, INSTRUCTION (ENGLISH)
(US, CND, E, TW)
2-593-810-21 MANUAL, INSTRUCTION (FRENCH) (CND)
2-593-810-31 MANUAL, INSTRUCTION (ENGLISH, SPANISH)
(SP, KR, TH, AUS)
2-593-810-41 MANUAL, INSTRUCTION (FRENCH, GERMAN)
(SP)
CORD, POWER (E, MX)

CORD, POWER (SP, TH)
CORD, POWER (KR)
CORD, POWER (US, CND)
CORD, POWER (AUS)
2-593-811-11 MANUAL, INSTRUCTION (SPANISH) (E, MX)

2-593-811-21 MANUAL, INSTRUCTION (KOREAN) (KR)
2-593-811-31 MANUAL, INSTRUCTION
(TRADITIONAL CHINESE) (TW)
2-598-716-11 MANUAL, INSTRUCTION (for SonicStage)
(ENGLISH) (US, CND, E, TW)
(FRENCH) (CND)
(ENGLISH, SPANISH) (SP, KR, TH, AUS)
(FRENCH, GERMAN) (SP)
(KOREAN) (KR)
(TRADITIONAL CHINESE) (TW)
47
ZS-SN10
Ver. 1.1
Ref. No.
Part No.
Description
Remark

(SPANISH) (E, MX)
3-267-151-01 LID BATTERY (for RMT-CYN7A)
(for BLACK, SILVER)
3-267-151-21 LID BATTERY (for RMT-CYN7A) (for WHITE)
A-1056-325-A REMOTE COMMANDER (RMT-CYN7A/HC)
(for SILVER)
A-1109-498-A REMOTE COMMANDER (RMT-CYN7A/BC)
(for BLACK)
A-1109-500-A REMOTE COMMANDER (RMT-CYN7A/WC)
(for WHITE)
X-2059-463-1 CD-ROM (APPLICATION) ASSY (SS3.0)
(SonicStage)
48
Ref. No.
Part No.
Description
Remark
ZS-SN10
MEMO
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
49
ZS-SN10
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
Date
Description of Revision
1.0
2005.04
New
1.1
2005.06
Addition of Thai model

Revision of electrical parts
Revision of mechanical parts
1.2
2005.07
Addition of E model
1.3
2006.02
Addition of silver type to US model

Revision of electrical parts
1.4
2006.03
Addition of silver type to Canadian model

Revision of mechanical parts

Service Manual: ZS-SN10

Uploaded by

Copyright:

Available Formats

Service Manual: ZS-SN10

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: ZS-SN10

Uploaded by

Copyright:

Available Formats

ZS-SN10

Ver. 1.4 2006.03

US and foreign patents licensed from Dolby Laboratories.

Model Name Using Similar Mechanism

Optical Pick-up Block Name

Optical Pick-up Name

POWER OUTPUT AND TOTAL HARMONIC

SP, KR, TH, AUS models:

AUDIO POWER SPECIFICATIONS

9 V DC, 6 size D (R20) batteries

PERSONAL AUDIO SYSTEM

SERVICING NOTES ................................................ 3

Disassembly Flow ...........................................................

ELECTRICAL ADJUSTMENTS .......................... 10

Block Diagram CD Servo Section ............................

Cabinet Section ................................................................

ELECTRICAL PARTS LIST .................................. 39

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

Fig. A. Using an AC voltmeter to check AC leakage.

ATTENTION AU COMPOSANT AYANT RAPPORT

LASER DIODE AND FOCUS SEARCH OPERATION

3. Press the u button.

Fig.1 Method to push the S801

This section is extracted from

Press u (N on the remote) (direct

ATRAC CD/MP3 CD*

* When playing an MP3 CD, MP3

Connect the supplied AC power cord.

Press PUSH Z OPEN/CLOSE to

With the label side up

Use these buttons for additional operations

Press PUSH Z OPEN/CLOSE to

adjust the volume

VOLUME +* 1, (VOL +* 1, on the

u*1 (X on the remote)

go to the next track

*1 The button has a tactile dot.

turn on/off the player

*2 This function works for ATRAC CDs/MP3 CDs only.

The structure of ATRAC CDs/MP3 CDs

Notes on ATRAC CDs

Listening to the radio

Connect the supplied AC power cord.

adjust the volume

VOLUME +*, (VOL +*, on the

turn on/off the radio

* The button has a tactile dot.

To improve broadcast reception

Hold down TUNE + or until the

If you cant tune in a station, press

3-1. DISASSEMBLY FLOW

3-2. CABINET TOP ASSY

3-3. MAIN BOARD

3-6. CD BLOCK ASSY

3-4. CABINET FRONT ASSY

3-7. OPTICAL PICK-UP

3-5. LCD BOARD

Note: Follow the disassembly procedure in the numerical order given.

VOLUME +, (VOL +, on the