Scribd Logo
Upload

Welcome to Scribd!

  • 33 views

    Swagelok A2333 Data Sheet

    Uploaded by

    vanpups
    This document provides suggested allowable working pressures for stainless steel tubing based on tube wall thickness and outer diameter. It notes that for welded tubing, the working pressure must be derated depending on whether it is double or single welded. It also provides ordering information for high quality stainless steel hydraulic tubing that meets specifications.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Swagelok A2333 Data Sheet

    Uploaded by

    vanpups
    33 views1 page
    This document provides suggested allowable working pressures for stainless steel tubing based on tube wall thickness and outer diameter. It notes that for welded tubing, the working pressure must be derated depending on whether it is double or single welded. It also provides ordering information for high quality stainless steel hydraulic tubing that meets specifications.

    Original Description:

    Swagelock datasheet.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides suggested allowable working pressures for stainless steel tubing based on tube wall thickness and outer diameter. It notes that for welded tubing, the working pressure must be derated depending on whether it is double or single welded. It also provides ordering information for high quality stainless steel hydraulic tubing that meets specifications.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    33 views1 page

    Swagelok A2333 Data Sheet

    Uploaded by

    vanpups
    This document provides suggested allowable working pressures for stainless steel tubing based on tube wall thickness and outer diameter. It notes that for welded tubing, the working pressure must be derated depending on whether it is double or single welded. It also provides ordering information for high quality stainless steel hydraulic tubing that meets specifications.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    4

    Tubing Data

    Suggested Allowable Working Pressure for Stainless Steel Tubing


    Table 3Fractional Stainless Steel Seamless Tubing
    Allowable working pressures are calculated from an S value of 20 000 psi (137.8 MPa) for ASTM A269 tubing at 20 to 100F (28 to 37C), as listed in ASME B31.3 and ASMEB31.1, except as noted.

    For Welded Tubing


    For welded and drawn tubing, a derating factor must be applied for weld integrity:
    for double-welded tubing, multiply working pressure by 0.85 for single-welded tubing, multiply working pressure by 0.80. Tube Wall Thickness, in. 0.010 0.012 0.014 0.016 Tube OD in. 1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1 1/4 1 1/2 2 0.035 0.049 0.065 0.083 0.095 0.109 0.120 0.134 0.156 0.188 Working Pressure, psig Swagelok Note: For gas service, select a tube wall thickness outside of the shaded area. Fitting (See Gas Service, page 2.) Series 100 8500 5400 4000 10 900 7 000 10 200 5 100 4 000 3 300 2 600 7 500 10 200 5 800 4 800 3 700 2 900 2 400 2 000 8 000 6 500 5 100 4 000 3 300 2 800 2 400 7500 6700 5200 4200 3600 3100 2400 6000 4900 5800 4200 4800 3600 4200 4700 2800 3300 3600 4100 4900 2300 2700 3000 3400 4000 4900 2000 2200 2500 2900 3600 200 300 400 500 600 810 1010 1210 1410 1610 2000 2400 3200 0.020 0.028

    5600 6800 8100 9400 12 000

    For higher pressures, see the Swagelok Medium-Pressure Fittings catalog, MS02335, or the Swagelok High-Pressure Fittings catalog, MS-01-34. Rating based on repeated pressure testing of the Swagelok tube fitting with a 4:1 design factor based upon hydraulic fluid leakage.

    Suggested Ordering Information


    High-quality, fully annealed (Type 304, 304/304L, 316, 316/316L, 317, 317/317L) (seamless or welded and drawn) stainless steel hydraulic tubing, ASTM A269 or A213, or equivalent. Hardness not to exceed 90 HRB or 200 HV. Tubing to be free of scratches, suitable for bending and flaring. OD tolerances not to exceed 0.003 in. for 1/16 in. OD tubing. Note:  Certain austenitic stainless tubing has an allowable ovality tolerance double the OD tolerance and may not fit into Swagelok precision tube fittings. Dual-certified grades such as 304/304L, 316/316L, and 317/317L meet the minimum chemistry and the mechanical properties of both alloy grades.

    You might also like