KSB CPKN

Standardised Chemical Pump
CPKN
Bearings UP02 to UP06 and P08s
Installation/Operating Manual
Legal information/Copyright
Installation/Operating Manual CPKN Original operating manual KSB Aktiengesellschaft All rights reserved. The contents provided herein must neither be distributed, copied, reproduced, edited or processed for any other purpose, nor otherwise transmitted, published or made available to a third party without KSB's express written consent. Subject to technical modification without prior notice. KSB Aktiengesellschaft Frankenthal 13.09.2012
Contents
Contents
Glossary .................................................................................................5 1
1.1 1.2 1.3 1.4 1.5
General ..................................................................................................6
Principles ...........................................................................................................6 Installation of partly completed machinery .................................................... 6 Target group ..................................................................................................... 6 Other applicable documents ............................................................................ 6 Symbols .............................................................................................................6
2
2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10
Safety .....................................................................................................8
Key to safety symbols/markings ....................................................................... 8 General .............................................................................................................. 8 Intended use .....................................................................................................8 Personnel qualification and training ............................................................... 9 Consequences and risks caused by non-compliance with these operating instructions ........................................................................................................ 9 Safety awareness ..............................................................................................9 Safety information for the operator/user ..................................................... 10 Safety information for maintenance, inspection and installation work ..... 10 Unauthorised modes of operation ................................................................ 10 Explosion protection ...................................................................................... 10
3
3.1 3.2 3.3 3.4 3.5
Transport/Temporary Storage/Disposal .............................................13

Checking the condition upon delivery .......................................................... 13 Transport ......................................................................................................... 13 Storage/preservation ...................................................................................... 14 Return to supplier ........................................................................................... 14 Disposal ...........................................................................................................15
4
4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8
Description of the Pump (Set) ............................................................16

General description ........................................................................................ 16 Designation ..................................................................................................... 16 Name plate ...................................................................................................... 16 Design details .................................................................................................. 16 Design and function ....................................................................................... 19 Noise characteristics ...................................................................................... 20 Scope of supply ............................................................................................... 20 Dimensions and weights ................................................................................20
5
5.1 5.2 5.3 5.4
Installation at Site ...............................................................................21

Safety regulations ........................................................................................... 21 Checks to be carried out prior to installation ............................................... 21 Installing the pump set .................................................................................. 21 Piping .............................................................................................................. 23
CPKN
3 of 70
Contents
5.5 5.6 5.7 5.8 5.9
Enclosure/insulation .......................................................................................26 Checking the coupling alignment ................................................................. 27 Aligning the pump and motor ...................................................................... 28 Electrical connection ...................................................................................... 29 Checking the direction of rotation ................................................................ 31
6
6.1 6.2 6.3 6.4
Commissioning/Start-up/Shutdown ...................................................32
Commissioning/start-up ................................................................................. 32 Operating limits .............................................................................................. 39 Shutdown/storage/preservation .................................................................... 41 Returning to service .......................................................................................41
7
7.1 7.2 7.3 7.4 7.5 7.6 7.7
Servicing/Maintenance .......................................................................42
Safety regulations ........................................................................................... 42 Maintenance/inspection ................................................................................. 43 Drainage/cleaning ..........................................................................................48 Dismantling the pump set .............................................................................. 48 Reassembling the pump set ........................................................................... 52 Tightening torques ......................................................................................... 57 Spare parts stock ............................................................................................. 57
8 9
9.1
Trouble-shooting ................................................................................60 Related Documents ............................................................................62

General assembly drawing with list of components .................................... 62
10 11
EC Declaration of Conformity ............................................................66 Certificate of Decontamination .........................................................67 Index ....................................................................................................68
4 of 70
CPKN
Glossary
Glossary
Back pull-out design
The complete back pull-out unit can be pulled out without having to remove the pump casing from the piping.
Hydraulic system
The part of the pump in which the kinetic energy is converted into pressure energy
Back pull-out unit

Pump without pump casing; partly completed machinery
Pool of pumps
Pumps which are purchased and stored independently of their later use
Certificate of decontamination
A certificate of decontamination is enclosed by the customer when returning the product to the manufacturer to certify that the product has been properly drained to eliminate any environmental and health hazards arising from components in contact with the fluid handled.
Pump
Machine without drive, additional components or accessories
Pump set
Complete pump set consisting of pump, drive, additional components and accessories
Discharge line
The line which is connected to the discharge nozzle
Suction lift line/suction head line

The line which is connected to the suction nozzle
CPKN
5 of 70
1 General
1 General
1.1 Principles
This operating manual is supplied as an integral part of the type series and variants indicated on the front cover. The manual describes the proper and safe use of this equipment in all phases of operation. The name plate indicates the type series and size, the main operating data, the order number and the order item number. The order number and order item number uniquely identify the pump (set) and serve as identification for all further business processes. In the event of damage, contact your nearest KSB service centre immediately to maintain the right to claim under warranty. Noise characteristics.( Section 4.6 Page 20)
1.2 Installation of partly completed machinery

To install partly completed machinery supplied by KSB, refer to the sub-sections under Servicing/Maintenance.( Section 7.5.5 Page 56)
1.3 Target group

This manual is aimed at the target group of trained and qualified specialist technical personnel.( Section 2.4 Page 9)
1.4 Other applicable documents

Table 1: Overview of other applicable documents Document Data sheet General arrangement drawing/ outline drawing Drawing of auxiliary connections Hydraulic characteristic curve General assembly drawing1) Sub-supplier product literature1) Spare parts lists1) Piping layout1) List of components1) Drawing for assembly Contents Description of the technical data of the pump (set) Description of mating and installation dimensions for the pump (set), weights Description of auxiliary connections Characteristic curves showing head, NPSH required, efficiency and power input Sectional drawing of the pump Operating manuals and other product literature describing accessories and integrated machinery components Description of spare parts Description of auxiliary piping Description of all pump components Sectional drawing for fitting the shaft seal
For accessories and/or integrated machinery components observe the relevant manufacturer's product literature.
1.5 Symbols
Table 2: Symbols used in this manual Symbol Description Conditions which need to be fulfilled before proceeding with the step-by-step instructions Safety instructions Result of an action Cross-references
1)
If agreed to be included in the scope of supply
6 of 70
CPKN
1 General
Symbol 1. 2.
Description Step-by-step instructions Note Recommendations and important information on how to handle the product
CPKN
7 of 70
2 Safety
2 Safety
!
DANGER
All the information contained in this section refers to hazardous situations.
2.1 Key to safety symbols/markings

Table 3: Definition of safety symbols/markings Symbol
!
DANGER WARNING
CAUTION
Description DANGER This signal word indicates a high-risk hazard which, if not avoided, will result in death or serious injury. WARNING This signal word indicates a medium-risk hazard which, if not avoided, could result in death or serious injury. CAUTION This signal word indicates a hazard which, if not avoided, could result in damage to the machine and its functions. Explosion protection This symbol identifies information about avoiding explosions in potentially explosive atmospheres in accordance with EC Directive 94/9/EC (ATEX). General hazard In conjunction with one of the signal words this symbol indicates a hazard which will or could result in death or serious injury. Electrical hazard In conjunction with one of the signal words this symbol indicates a hazard involving electrical voltage and identifies information about protection against electrical voltage. Machine damage In conjunction with the signal word CAUTION this symbol indicates a hazard for the machine and its functions.
2.2 General
This manual contains general installation, operating and maintenance instructions that must be observed to ensure safe pump operation and prevent personal injury and damage to property. The safety information in all sections of this manual must be complied with. This manual must be read and completely understood by the specialist personnel/ operators responsible prior to installation and commissioning. The contents of this manual must be available to the specialist personnel at the site at all times. Information attached directly to the pump must always be complied with and be kept in a perfectly legible condition at all times. This applies to, for example: Arrow indicating the direction of rotation Markings for connections Name plate The operator is responsible for ensuring compliance with all local regulations not taken into account in this manual.
2.3 Intended use

The pump (set) must only be operated within the operating limits described in the other applicable documents.( Section 1.4 Page 6) Only operate pumps/pump sets which are in perfect technical condition. Do not operate the pump (set) in partially assembled condition. Only use the pump to handle the fluids described in the data sheet or product literature of the pump model.
8 of 70
CPKN
2 Safety
Never operate the pump without the fluid handled. Observe the minimum flow rates indicated in the data sheet or product literature (to prevent overheating, bearing damage, etc). Observe the maximum flow rates indicated in the data sheet or product literature (to prevent overheating, mechanical seal damage, cavitation damage, bearing damage, etc). Do not throttle the flow rate on the suction side of the pump (to prevent cavitation damage). Consult the manufacturer about any use or mode of operation not described in the data sheet or product literature. Prevention of foreseeable misuse Never open discharge-side shut-off elements further than permitted. The maximum flow rate specified in the data sheet or product literature would be exceeded. Risk of cavitation damage Never exceed the permissible operating limits specified in the data sheet or product literature regarding pressure, temperature, etc. Observe all safety information and instructions in this manual.
2.4 Personnel qualification and training

All personnel involved must be fully qualified to transport, install, operate, maintain and inspect the machinery this manual refers to. The responsibilities, competence and supervision of all personnel involved in transport, installation, operation, maintenance and inspection must be clearly defined by the operator. Deficits in knowledge must be rectified by means of training and instruction provided by sufficiently trained specialist personnel. If required, the operator can commission the manufacturer/supplier to train the personnel. Training on the pump (set) must always be supervised by technical specialist personnel.
2.5 Consequences and risks caused by non-compliance with these operating instructions
Non-compliance with these operating instructions will lead to forfeiture of warranty cover and of any and all rights to claims for damages. Non-compliance can, for example, have the following consequences: Hazards to persons due to electrical, thermal, mechanical and chemical effects and explosions Failure of important product functions Failure of prescribed maintenance and servicing practices Hazard to the environment due to leakage of hazardous substances
2.6 Safety awareness

In addition to the safety information contained in this manual and the intended use, the following safety regulations shall be complied with: Accident prevention, health and safety regulations Explosion protection regulations Safety regulations for handling hazardous substances Applicable standards and laws
CPKN
9 of 70
2 Safety
2.7 Safety information for the operator/user

The operator shall fit contact guards for hot, cold and moving parts and check that the guards function properly. Do not remove any contact guards during operation. Provide the personnel with protective equipment and make sure it is used. Contain leakages (e.g. at the shaft seal) of hazardous fluids handled (e.g. explosive, toxic, hot) so as to avoid any danger to persons and the environment. Adhere to all relevant laws. Eliminate all electrical hazards. (In this respect refer to the applicable national safety regulations and/or regulations issued by the local energy supply companies.) If shutting down the pump does not increase potential risk, fit an emergencystop control device in the immediate vicinity of the pump (set) during pump set installation.
2.8 Safety information for maintenance, inspection and installation work

Modifications or alterations of the pump are only permitted with the manufacturer's prior consent. Use only original spare parts or parts authorised by the manufacturer. The use of other parts can invalidate any liability of the manufacturer for resulting damage. The operator ensures that all maintenance, inspection and installation work is performed by authorised, qualified specialist personnel who are thoroughly familiar with the manual. Only carry out work on the pump (set) during standstill of the pump. The pump casing must have cooled down to ambient temperature. Pump pressure must have been released and the pump must have been drained. When taking the pump set out of service always adhere to the procedure described in the manual.( Section 6.1.12 Page 38)( Section 6.3 Page 41) Decontaminate pumps which handle fluids posing a health hazard.( Section 7.3 Page 48) As soon as the work is completed, re-install and/or re-activate any safety-relevant and protective devices. Before returning the product to service, observe all instructions on commissioning.( Section 6.1 Page 32)
2.9 Unauthorised modes of operation

Never operate the pump (set) outside the limits stated in the data sheet and in this manual. The warranty relating to the operating reliability and safety of the supplied pump (set) is only valid if the equipment is used in accordance with its intended use.( Section 2.3 Page 8)
2.10 Explosion protection

!
DANGER
Always observe the information on explosion protection given in this section when operating the pump in potentially explosive atmospheres. Only pumps/pump sets marked as explosion-proof and identified as such in the data sheet may be used in potentially explosive atmospheres. Special conditions apply to the operation of explosion-proof pump sets to EC Directive 94/9/EC (ATEX). Especially adhere to the sections in this manual marked with the Ex symbol and the following sections( Section 2.10.1 Page 11) to( Section 2.10.4 Page 12) ( Section 2.10.3 Page 11). The explosion-proof status of the pump set is only assured if the pump set is used in accordance with its intended use.
10 of 70
CPKN
2 Safety
Never operate the pump set outside the limits stated in the data sheet and on the name plate. Prevent impermissible modes of operation at all times. 2.10.1 Marking Pump The marking on the pump refers to the pump part only. Example of such marking: II 2 G c TX Refer to the Temperature limits table for the temperatures permitted for the individual pump variants.( Section 2.10.2 Page 11) An EC manufacturer's declaration is required for the shaft coupling; the shaft coupling must be marked accordingly. The motor must be considered separately. 2.10.2 Temperature limits In normal pump operation, the highest temperatures are to be expected on the surface of the pump casing, at the shaft seal and in the bearing areas. The surface temperature at the pump casing corresponds to the temperature of the fluid handled. If the pump is heated in addition, the operator of the system is responsible for observing the specified temperature classes and fluid temperature (operating temperature). The table below lists the temperature classes and the resulting theoretical temperature limits of the fluid handled (a possible temperature rise in the shaft seal area has already been taken into account). The temperature class specifies the maximum permissible temperature at the surface of the pump set during operation. For the permissible operating temperature of the pump in question refer to the data sheet. Table 4: Temperature limits Temperature class to EN 13463-1 T1 T2 T3 T4 T5 T6 Temperature class T5 Maximum permissible fluid temperature Maximum 400 C2) 280 C 185 C 120 C 85 C Only after consultation with the manufacturer
Shaft coupling Motor
Based on an ambient temperature of 40 C and proper maintenance and operation, compliance with temperature class T5 is warranted in the area of the rolling element bearings. If the ambient temperature exceeds 40 C, contact the manufacturer. A special design is required to comply with the requirements of temperature class T6 in the bearing area. Misuse, malfunctions or non-compliance with the instructions may result in substantially higher temperatures. If the pump is to be operated at a higher temperature, if there is no data sheet or if the pump is part of a pool of pumps, contact KSB for the maximum permissible operating temperature. 2.10.3 Monitoring equipment The pump (set) must only be operated within the limits specified in the data sheet and on the name plate. If the system operator cannot warrant compliance with these operating limits, appropriate monitoring devices must be used. Check whether monitoring equipment is required to ensure that the pump set functions properly.
Temperature class T6
2)
Depending on the material variant
CPKN
11 of 70
2 Safety
Contact KSB for further information on monitoring equipment. 2.10.4 Operating limits The minimum flows indicated in ( Section 6.2.3.1 Page 40) refer to water and waterlike fluids. Longer operating periods with these fluids and at the flow rates indicated will not cause an additional increase in the temperatures at the pump surface. However, if the physical properties of the fluids handled are different from water, it is essential to check whether an additional heat build-up may occur and if the minimum flow rate must therefore be increased. The calculation formula in( Section 6.2.3.1 Page 40) can be used to check whether an additional heat build-up may lead to a hazardous temperature increase at the pump surface.
12 of 70
CPKN
3 Transport/Temporary Storage/Disposal
3.1 Checking the condition upon delivery
1. 2. On transfer of goods, check each packaging unit for damage. In the event of in-transit damage, assess the exact damage, document it and notify KSB or the supplying dealer (as applicable) and the insurer about the damage in writing immediately.
3.2 Transport
DANGER
The pump (set) could slip out of the suspension arrangement Danger to life from falling parts! Always transport the pump (set) in the specified position. Never attach the suspension arrangement to the free shaft end or the motor eyebolt. Give due attention to the weight data and the centre of gravity. Observe the applicable local health and safety regulations. Use suitable, permitted lifting accessories, e.g. self-tightening lifting tongs. To transport the pump/pump set or back pull-out unit suspend it from the lifting tackle as shown below.
Fig. 1: Transporting the back pull-out unit
Fig. 2: Transporting the pump
CPKN
13 of 70
90
Fig. 3: Transporting the complete pump set
90
Fig. 4: Transporting the pump on the baseplate
3.3 Storage/preservation
If commissioning is to take place some time after delivery, we recommend that the following measures be taken for pump (set) storage.
CAUTION
Damage during storage by humidity, dirt, or vermin Corrosion/contamination of the pump (set)! For outdoor storage cover the packed or unpacked pump (set) and accessories with waterproof material.
CAUTION
Wet, contaminated or damaged openings and connections Leakage or damage to the pump set! Only remove caps/covers from the openings of the pump set at the time of installation. Store the pump (set) in a dry, protected room where the atmospheric humidity is as constant as possible. Rotate the shaft by hand once a month, e.g. via the motor fan. If properly stored indoors, the pump set is protected for a maximum of 12 months. New pumps/pump sets are supplied by our factory duly prepared for storage. For storing a pump (set) which has already been operated, observe the instructions in( Section 6.3.1 Page 41) .
3.4 Return to supplier

1. 2. Drain the pump as per operating instructions.( Section 7.3 Page 48) Always flush and clean the pump, particularly if it has been used for handling noxious, explosive, hot or other hazardous fluids.
14 of 70
CPKN
3.
If the fluids handled by the pump set leave residues which might lead to corrosion damage when coming into contact with atmospheric humidity, or which might ignite when coming into contact with oxygen, the pump set must also be neutralised, and anhydrous inert gas must be blown through the pump for drying purposes. Always complete and enclose a certificate of decontamination when returning the pump (set). Always indicate any safety and decontamination measures taken.( Section 11 Page 67)
4.
NOTE
If required, a blank certificate of decontamination can be downloaded from the KSB web site at: www.ksb.com/certificate_of_decontamination
3.5 Disposal
WARNING
Fluids and supplies posing a health hazard and/or hot fluids and supplies Hazard to persons and the environment! Collect and properly dispose of flushing medium and any residues of the fluid handled. Wear safety clothing and a protective mask, if required. Observe all legal regulations on the disposal of fluids posing a health hazard. 1. 2. Dismantle the pump (set). Collect greases and other lubricants during dismantling. Separate and sort the pump materials, e.g. by: - Metals - Plastics - Electronic waste - Greases and other lubricants Dispose of materials in accordance with local regulations or in another controlled manner.
3.
CPKN
15 of 70
4 Description of the Pump (Set)

4.1 General description
Standardised chemical pump with shaft seal Pump for handling aggressive liquids in the chemical and petrochemical industries.
4.2 Designation
Example: CPKN - C1 F 40-160 Table 5: Key to the designation Code CPKN C1 F 40 160 Description Type series Casing material, e.g. C1 = stainless steel Additional code, e.g. F = off-standard flange design Nominal discharge nozzle diameter [mm] Nominal impeller diameter [mm]
4.3 Name plate

1 2 3 4 5
KSB Aktiengesellschaft 67227 Frankenthal
2008 CPKN-C1.V 080-160 0520-5-P-10000-31 P-No. 997125086300550001 Q 115 m3/h H 25 m n 2955 1/min
Mat-No. 01 109 223 ZN 3804 - D 52 x 74
Fig. 5: Name plate (example) 1 3 5 7 Type series, size ( Section 4.2 Page 16) KSB order and order item number Speed Head 2 4 6 Customer-specific information (optional) Flow rate Year of construction
4.4 Design details

Design Volute casing pump Horizontal installation Back pull-out design Single-stage Meets the technical requirements to ISO 5199 Dimensions and ratings to EN 22858/ISO 2858, complemented by pumps of nominal diameters DN 25, DN 200 and above Pump casing Single or double volute, depending on the pump size Radially split volute casing Volute casing with integrally cast pump feet Volute casing (partly with casing wear ring) and casing cover
16 of 70
CPKN
Impeller type Closed radial impeller with multiply curved vanes Back vanes reduce axial thrust Shaft seal Gland packing Commercial single and double mechanical seals Preferable: Standardised mechanical seals to EN 12756, "K" design
NOTE
Conversion from gland packing to mechanical seal and vice versa is possible without any rework on the casing cover by using the relevant replacement parts. Possible: Commercial cartridge seals Alternative: Version without shaft protecting sleeve with "wet shaft" Table 6: Seal chamber with different shaft seals (examples) Type of seal Conical seal chamber (A-type cover) Standardised mechanical seal Illustration
D00458
Cylindrical seal chamber Standardised mechanical seal
D00459
Cartridge seal
D00460
Double mechanical seal (back-toback) both sides unbalanced
D01167
Bearings Drive-end bearing: Fixed bearing Paired angular contact ball bearings Axial movement of the rotor limited to maximum 0.5 mm
CPKN
17 of 70
Oil lubrication Optional: grease lubrication Pump-end bearing: Radial bearing Cylindrical roller bearing Absorbs radial loads only Oil lubrication Optional: grease lubrication Bearing bracket designation Example: UP03 Table 7: Bearing bracket designation Code UP 03 Bearings used Table 8: Bearing design KSB designation B.G B.G.8 Bearing bracket UP02 UP03 UP04 UP05 UP06 P08s FAG designation B-TVP-UA B-TVP-UA 80 SKF designation BECBP BEC86P Description Bearing bracket Size code (based on dimensions of seal chamber and shaft end)
Table 9: Standard bearing assembly Rolling element bearing Pump end NU307 NU311 NU311 NU313 NU416 NU416 Drive end 2 x 7307 B.G 2 x 7311 B.G.8 2 x 7311 B.G.8 2 x 7313 B.G.8 2 x 7319 B.G 2 x 7319 B.G
18 of 70
CPKN
4.5 Design and function
Fig. 6: Sectional drawing 1 3 5 7 9 Clearance gap Casing cover Bearing bracket Impeller Rolling element bearing, pump end 2 4 6 8 10 Discharge nozzle Drive shaft Suction nozzle Shaft seal Rolling element bearing, drive end
Design
The pump is designed with an axial fluid inlet and a radial or tangential outlet. The hydraulic system runs in its own bearings and is connected to the motor by a shaft coupling. The fluid enters the pump axially via the suction nozzle (6) and is accelerated outward by the rotating impeller (7). In the flow passage of the pump casing the kinetic energy of the fluid is converted into pressure energy. The fluid is pumped to the discharge nozzle (2), where it leaves the pump. The clearance gap (1) prevents any fluid from flowing back from the casing to the suction nozzle. At the rear side of the impeller, the shaft (4) enters the casing via the casing cover (3). The shaft passage through the cover is sealed towards the atmosphere with a shaft seal (8). The shaft runs in rolling element bearings (9 and 10), which are supported by a bearing bracket (5) linked with the pump casing and/or casing cover. The pump is sealed by a shaft seal (standardised mechanical seal or gland packing).
Function
Sealing
CPKN
19 of 70
4.6 Noise characteristics

Table 10: Surface sound pressure level LpA3)4) Rated power input PN[kW] 1.5 2.2 3 4 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 132 160 200 250 Pump 960 rpm 760 rpm [dB] 52 53 55 56 58 59 61 63 64 65 66 67 68 69 71 71 72 73 74 75 1450 rpm [dB] 53 55 56 58 59 61 63 65 66 67 68 70 71 72 73 74 75 76 77 78 79 2900 rpm [dB] 54 56 57 59 61 62 64 66 67 68 70 71 72 73 75 76 77 78 79 80 81 960 rpm 760 rpm [dB] 56 58 60 61 62 64 65 67 68 68 70 70 71 72 73 73 74 75 75 76 Pump set 1450 rpm [dB] 58 60 62 63 65 66 68 69 70 71 72 73 74 74 76 76 77 77 78 79 80 2900 rpm [dB] 63 66 68 69 71 72 74 75 76 77 78 79 80 80 81 82 82 83 84 84 85
4.7 Scope of supply

Depending on the model, the following items are included in the scope of supply: Pump Drive Shaft coupling Contact guard Baseplate Surface-cooled IEC three-phase squirrel-cage motor Flexible coupling with or without spacer Coupling guard Baseplate (to ISO 3661), cast or welded, for pump and motor, in torsion-resistant design Channel section steel or folded steel plate Special accessories As required
4.8 Dimensions and weights

For dimensions and weights please refer to the general arrangement drawing/outline drawing of the pump/pump set.
3) 4)
Spatial average; as per ISO 3744 and EN 12639; valid for pump operation in the Q/Qopt = 0.8 - 1.1 range and for noncavitating operation. If noise levels are to be guaranteed: Add +3 dB for measuring and constructional tolerance. Increase for 60 Hz operation: 3500 rpm+3 dB; 1750 rpm +1 dB; 1160 rpm:0 dB
20 of 70
CPKN
5 Installation at Site
5.1 Safety regulations
DANGER
Improper installation in potentially explosive atmospheres Explosion hazard! Damage to the pump set! Comply with the applicable local explosion protection regulations. Observe the information in the data sheet and on the name plates of pump and motor.
5.2 Checks to be carried out prior to installation

Place of installation
WARNING
Installation on mounting surface which is unsecured and cannot support the load Personal injury and damage to property! Use a concrete of compressive strength class C12/15 which meets the requirements of exposure class XC1 to EN 206-1. The mounting surface must have set and must be completely horizontal and even. Observe the weights indicated. 1. Check the structural requirements. All structural work required must have been prepared in accordance with the dimensions stated in the outline drawing/general arrangement drawing.
5.3 Installing the pump set

Always install the pump set in horizontal position.
DANGER
Excessive temperatures due to improper installation Explosion hazard! Install the pump in horizontal position to ensure self-venting of the pump.
5.3.1 Installation on the foundation
2
Fig. 7: Fitting the shims L 2 Bolt-to-bolt distance Shim if (L) > 800 mm 1 3
3
Shim Foundation bolt
The foundation has the required strength and characteristics.
CPKN
21 of 70
The foundation has been prepared in accordance with the dimensions given in the outline drawing/general arrangement drawing. 1. Position the pump set on the foundation and level it with the help of a spirit level placed on the shaft and discharge nozzle. Permissible deviation: 0.2 mm/m. Use shims (1) for height compensation, if necessary. Always fit shims, if any, immediately to the left and right of the foundation bolts (3) between the baseplate/foundation frame and the foundation. For a bolt-to-bolt distance (L) > 800 mm fit additional shims (2) halfway between the bolt holes. All shims must lie perfectly flush. Insert the foundation bolts (3) into the holes provided. Use concrete to set the foundation bolts (3) into the foundation. Wait until the concrete has set firmly, then level the baseplate. Tighten the foundation bolts (3) evenly and firmly. Grout the baseplate using low-shrinkage concrete with a standard particle size and a water/cement ratio of 0.5. Produce flowability with the help of a solvent. Perform secondary treatment of the concrete to DIN 1045.
2.
3. 4. 5. 6. 7.
NOTE
For low-noise operation contact KSB to check whether the pump set can be installed on anti-vibration mounts.
NOTE
Expansion joints can be fitted between pump and suction/discharge line.
5.3.2 Installation without foundation
1 2
4
Fig. 8: Adjusting the levelling elements 1, 3 4 1. 2. 3. Locknut Levelling element 2 Levelling nut
The installation surface has the required strength and characteristics. Position the pump set on the levelling elements (4) and level it with the help of a spirit level (on the shaft/discharge nozzle). To adjust any differences in height, loosen the bolts and locknuts (1, 3) of the levelling elements (4). Turn the levelling nut (2) until any differences in height have been compensated.
22 of 70
CPKN
4.
Re-tighten the locknuts (1, 3) at the levelling elements (4).
5.4 Piping
5.4.1 Connecting the piping
DANGER
Impermissible loads acting on the pump nozzles Danger to life from leakage of hot, toxic, corrosive or flammable fluids! Do not use the pump as an anchorage point for the piping. Anchor the pipelines in close proximity to the pump and connect them without transmitting any stresses or strains. Observe the permissible forces and moments at the pump nozzles.( Section 5.4.2 Page 24) Take appropriate measures to compensate thermal expansion of the piping.
CAUTION
Incorrect earthing during welding work at the piping Destruction of rolling element bearings (pitting effect)! Never earth the electric welding equipment on the pump or baseplate. Prevent current flowing through the rolling element bearings.
NOTE
It is recommended to install check and shut-off elements in the system, depending on the type of plant and pump. However, such elements must not obstruct proper drainage or hinder disassembly of the pump. The suction lift line has been laid with a rising slope, the suction head line with a downward slope towards the pump. A flow stabilisation section having a length equivalent to at least twice the diameter of the suction flange has been provided upstream of the suction flange. The nominal diameters of the pipelines are at least equal to the nominal diameters of the pump nozzles. Adapters to larger diameters have a diffuser angle of approximately 8 to prevent excessive pressure losses. The pipelines have been anchored in close proximity to the pump and connected without transmitting any stresses or strains.
CAUTION
Welding beads, scale and other impurities in the piping Damage to the pump! Free the piping from any impurities. If necessary, install a filter. Comply with the instructions set out in ( Section 7.2.2.3 Page 45). 1. 2. 3. 4. Thoroughly clean, flush and blow through all vessels, pipelines and connections (especially of new installations). Before installing the pump in the piping, remove the flange covers on the suction and discharge nozzles of the pump. Check that the inside of the pump is free from any foreign objects. Remove any foreign objects. If required, install a filter in the piping (see figure: Filter in the piping).
CPKN
23 of 70
2
Fig. 9: Filter in the piping 1 Differential pressure gauge 2 Filter
NOTE
Use a filter with laid-in wire mesh of 0.5 mm x 0.25 mm (mesh size x wire diameter) made of corrosion-resistant material. Use a filter with a filter area three times the cross-section of the piping. Conical filters have proved suitable. 5. Connect the pump nozzles to the piping.
CAUTION
Aggressive flushing and pickling agents Damage to the pump! Match the cleaning operation mode and duration for flushing and pickling service to the casing and seal materials used.
5.4.2 Permissible forces and moments at the pump nozzles
[+] Fy Fz Fx Fz Fx Fy Fz Mz Fx
Fy My Mx
The resulting permissible forces have been determined according to:
Forces and moments at the pump nozzles The data on forces and moments apply to static piping loads only. If the limits are exceeded, they must be checked and verified. If a computerised strength analysis is required, values are available on request only. The values are only applicable if the pump is installed on a completely grouted baseplate and bolted to a rigid and level foundation.
24 of 70
CPKN
Table 11: Forces and moments at the pump nozzles Pump size Suction nozzle [N] Fx 1050 1350 Fy 700 900 Fz 850 1100 Fres 1100 1400 Fx 500 700 Discharge nozzle [N] FyTens + 350 450 FyPress650 850 Fz 450 550 Fres 700 900 Suction nozzle [Nm] Mx 550 700 My 450 550 Mz 300 350 Discharge nozzle [Nm] Mx 400 450 My 300 350 Mz 200 250
25-160 25-200 32-125 32-160 32-200 32-250 40-160 40-200 40-250 40-315 50-160 50-200 50-250 50-315 65-160 65-200 65-250 65-315 80-160 80-200 80-250 80-315 80-400 100-200 100-250 100-315 100-400 125-250 125-315 125-400 150-250 150-315 150-400 150-500 200-250 200-315 200-400 200-500 250-315 250-400 250-500 300-400 300-500 350-400 350-500
1750
1150
1400
1800
850
550
1100
700
1100
1150
850
600
550
450
300
2150
1400
1700
2200
1100
700
1350
900
1400
1450 1100
750
700
550
350
2700
1750
2150
2750
1400
900
1750
1150
1800
2000 1500 1000 1150
850
600
3700
2400
2950
3800
1700
1100
2150
1400
2200
2750 2100 1400 1450 1100
750
3700
2400
2950
3800
2150
1350
2700
1750
2800
2750 2100 1400 2000 1500 1000
4700 7350
3100 4700
3750 5700
4750 7400
2950 3750
1850 2350
3700 4700
2400 3100
3800 4850
3450 2650 1750 2750 2100 1400 5300 3850 2650 3450 2650 1750
7350 4700 10000 6700
5700 7400 5700 8000 10450 5700
3550 3550
7350 7350
4700 4700
7400 7400
5300 3850 2650 5300 3850 2650 7500 5700 3650 5300 3850 2650
12000 8000 10000 12800 8000
5000 10000 6700 10450 9150 6900 4500 7500 5700 3650
13350 8700 10700 13800 10000 6150 12000 8000 12800 9550 7150 4700 9150 6900 4500 13350 8700 10700 13800 10700 6700 13350 8700 13800 9550 7150 4700 9550 7150 4700 Correction coefficients depending on material and temperature (see diagram below).
CPKN
25 of 70
Correction coefficient
1,00 0,95 0,90 0,85 0,80 0,75 0,70 0,65 0,60 0,55 0,50 120 150 200 250 300 350 1.4408 JL1040 GP240GH+N JS1025
400 C
Fig. 10: Temperature correction diagram 5.4.3 Auxiliary connections
DANGER
Risk of potentially explosive atmosphere as a result of incompatible liquids mixing in auxiliary piping Risk of burns! Explosion hazard! Make sure barrier/quench liquid is compatible with the fluid handled.
WARNING
Failure to use or incorrect use of auxiliary connections (e.g. barrier fluid, flushing liquid, etc.) Risk of injury from escaping fluid! Risk of burns! Malfunction of the pump! Refer to the general arrangement drawing, the piping layout and pump markings (if any) for the quantity, dimensions and locations of auxiliary connections. Use the auxiliary connections provided.
5.5 Enclosure/insulation
DANGER
Risk of potentially explosive atmosphere due to insufficient venting Explosion hazard! Make sure the space between the casing cover/discharge cover and the bearing cover is sufficiently vented. Never close or cover the perforation of the bearing bracket guards (e.g. by insulation).
WARNING
The volute casing and casing/discharge cover take on the same temperature as the fluid handled Risk of burns! Insulate the volute casing. Fit protective equipment.
26 of 70
CPKN
CAUTION
Heat build-up in the bearing bracket Damage to the bearing! Never insulate the bearing bracket, bearing bracket lantern and casing cover.
5.6 Checking the coupling alignment
DANGER
Inadmissible temperatures at the coupling or bearings due to misalignment of the coupling Explosion hazard! Risk of burns! Make sure that the coupling is correctly aligned at all times.
CAUTION
Misalignment of pump and motor shafts Damage to pump, motor and coupling! Always check the coupling after the pump has been installed and connected to the piping. Also check the coupling of pump sets supplied with pump and motor mounted on the same baseplate.
a)
b)
B A
1
1 Straight-edge
2
2
1
Wedge gauge
Fig. 11: Checking the coupling alignment: a) Coupling, b) Spacer-type coupling The coupling guard and the footboard for the coupling guard, if any, have been removed. 1. 2. 3. Loosen the support foot and re-tighten it without transmitting any stresses and strains. Place the straight-edge axially on both coupling halves. Leave the straight-edge in this position and turn the coupling by hand. The coupling is aligned correctly if the distances A) and B) to the respective shafts are the same at all points around the circumference. The radial and axial deviation between the two coupling halves must not exceed 0.1 mm during standstill as well as at operating temperature and under inlet pressure. Check the distance (dimension see general arrangement drawing) between the two coupling halves around the circumference. The coupling is aligned correctly if the distance between the two coupling
4.
CPKN
27 of 70
halves is the same at all points around the circumference. The radial and axial deviation of both coupling halves must not exceed 0.1 mm during standstill as well as at operating temperature and under inlet pressure. 5. If alignment is correct, re-install the coupling guard and the footboard for the coupling guard, if any.
5.7 Aligning the pump and motor

After having installed the pump set and connected the piping, check the coupling alignment and, if required, re-align the pump set (at the motor). 5.7.1 Motors with levelling screw
1 2 3
Fig. 12: Motor with levelling screw 1 3 Hexagon head bolt Locknut 2 Levelling screw
The coupling guard and the footboard for the coupling guard, if any, have been removed. 1. 2. 3. Check the coupling alignment. Unscrew the hexagon head bolts (1) at the motor and the locknuts (3) at the baseplate. Turn the levelling screws (2) by hand or by means of an open-jawed wrench until the coupling alignment is correct and all motor feet rest squarely on the baseplate. Re-tighten the hexagon head bolts (1) at the motor and the locknuts (3) at the baseplate. Check that the coupling and shaft can easily be rotated by hand.
4. 5.
WARNING
Unprotected rotating coupling Risk of injury by rotating shafts! Always operate the pump set with a coupling guard. If the customer specifically requests not to include a coupling guard in KSB's delivery, then the operator must supply one! Observe all relevant regulations for selecting a coupling guard.
DANGER
Risk of ignition by frictional sparks Explosion hazard! Choose a coupling guard material that is non-sparking in the event of mechanical contact (see DIN EN 13463-1). 6. Re-install the coupling guard and the footboard for the coupling guard, if any.
28 of 70
CPKN
7.
Check the distance between coupling and coupling guard. The coupling and coupling guard must not come into contact.
5.7.2 Motors without levelling screw Any differences in the centreline heights of the pump and motor shafts are compensated by means of shims.
1
Fig. 13: Pump set with shim 1 Shim The coupling guard and the footboard for the coupling guard, if any, have been removed. 1. 2. 3. 4. 5. Check the coupling alignment. Unscrew the hexagon head bolts at the motor. Insert shims underneath the motor feet until the difference in shaft centreline height has been compensated. Re-tighten the hexagon head bolts. Check that the coupling and shaft can easily be rotated by hand.
WARNING
Unprotected rotating coupling Risk of injury by rotating shafts! Always operate the pump set with a coupling guard. If the customer specifically requests not to include a coupling guard in KSB's delivery, then the operator must supply one! Observe all relevant regulations for selecting a coupling guard.
DANGER
Risk of ignition by frictional sparks Explosion hazard! Choose a coupling guard material that is non-sparking in the event of mechanical contact (see DIN EN 13463-1). 6. 7. Re-install the coupling guard and the footboard for the coupling guard, if any. Check the distance between coupling and coupling guard. The coupling and coupling guard must not come into contact.
5.8 Electrical connection
DANGER
Incorrect electrical installation Explosion hazard! For electrical installation, also observe the requirements of IEC 60079-14. Always connect explosion-proof motors via a motor protection switch.
CPKN
29 of 70
DANGER
Work on the pump set by unqualified personnel Danger of death from electric shock! Always have the electrical connections installed by a trained and qualified electrician. Observe regulations IEC 60364 and, for explosion-proof models, EN 60079.
WARNING
Incorrect connection to the mains Damage to the mains network, short circuit! Observe the technical specifications of the local energy supply companies. 1. 2. Check the available mains voltage against the data on the motor name plate. Select an appropriate start-up method.
NOTE
It is recommended to fit a motor protection device.
5.8.1 Setting the time relay
CAUTION
Switchover between star and delta on three-phase motors with star-delta starting takes too long. Damage to the pump (set)! Keep switch-over intervals between star and delta as short as possible. Table 12: Time relay settings for star-delta starting: Motor rating 30 kW > 30 kW 5.8.2 Earthing Y time to be set <3s <5s
DANGER
Electrostatic charging Explosion hazard! Damage to the pump set! Connect the PE conductor to the earthing terminal provided. Provide for potential equalisation between the pump set and foundation.
5.8.3 Connecting the motor
NOTE
In compliance with IEC 60034-8, three-phase motors are always wired for clockwise rotation (looking at the motor shaft stub). The pump's direction of rotation is indicated by an arrow on the pump. 1. 2. Match the motor's direction of rotation to that of the pump. Observe the manufacturer's product literature supplied with the motor.
30 of 70
CPKN
5.9 Checking the direction of rotation
DANGER
Temperature increase resulting from contact between rotating and stationary components Explosion hazard! Damage to the pump set! Never check the direction of rotation by starting up the unfilled pump set. Separate the pump from the motor to check the direction of rotation.
WARNING
Hands inside the pump casing Risk of injuries, damage to the pump! Always disconnect the pump set from the power supply and secure it against unintentional start-up before inserting your hands or other objects into the pump.
CAUTION
Incorrect direction of rotation with non-reversible mechanical seal Damage to the mechanical seal and leakage! Separate the pump from the motor to check the direction of rotation.
CAUTION
Drive and pump running in the wrong direction of rotation Damage to the pump! Refer to the arrow indicating the direction of rotation on the pump. Check the direction of rotation. If required, check the electrical connection and correct the direction of rotation. The correct direction of rotation of the motor and pump is clockwise (seen from the drive end). 1. 2. Start the motor and stop it again immediately to determine the motor's direction of rotation. Check the direction of rotation. The motor's direction of rotation must match the arrow indicating the direction of rotation on the pump. If the motor is running in the wrong direction of rotation, check the electrical connection of the motor and switchgear, if any.
3.
CPKN
31 of 70
6 Commissioning/Start-up/Shutdown
6.1 Commissioning/start-up
6.1.1 Prerequisites for commissioning/start-up Before commissioning/starting up the pump set, make sure that the following conditions are met: The pump set has been properly connected to the electric power supply and is equipped with all protection devices. The pump has been primed with the fluid to be handled.( Section 6.1.4 Page 33) The direction of rotation has been checked.( Section 5.9 Page 31) All auxiliary connections required are connected and operational. The lubricants have been checked. After prolonged shutdown of the pump (set), the activities described in ( Section 6.4 Page 41) have been carried out. 6.1.2 Filling in lubricants Grease-lubricated bearings Oil-lubricated bearings Grease-lubricated bearings have been packed with grease at the factory. Fill the bearing bracket with lubricating oil. Oil quality see( Section 7.2.3.1.2 Page 45) Oil quantity see ( Section 7.2.3.1.3 Page 46) Filling the constant-level oiler with lubricating oil (oil-lubricated bearings only) The constant-level oiler is screwed into the upper tapping hole of the bearing bracket.
NOTE
If no constant-level oiler is provided on the bearing bracket, the oil level can be read in the middle of the oil level sight glass arranged at the side of the bearing bracket.
CAUTION
Insufficient lubricating oil in the reservoir of the constant-level oiler Damage to the bearings! Regularly check the oil level. Always fill the oil reservoir completely. Keep the oil reservoir properly filled at all times.
Fig. 14: Bearing bracket with constant-level oiler
32 of 70
CPKN
1 3 5 1. 2. 3. 4. 5. 6. 7.
Constant-level oiler 2 Connection elbow of the constant- 4 level oiler Bearing bracket Pull out the vent plug (2).
Vent plug Screw plug
Hinge down the reservoir of the constant-level oiler (1) from the bearing bracket (5) and hold it in this position. Fill in oil through the hole for the vent plug until the oil reaches the connection elbow of the constant-level oiler (3). Completely fill the reservoir of the constant-level oiler (1). Snap the constant-level oiler (1) back into its operating position. Fit the vent plug (2) again. After approximately 5 minutes, check the oil level in the glass reservoir of the constant-level oiler (1). The oil reservoir must be properly filled at all times to ensure that the correct oil level is maintained. Repeat steps 1 - 6, if necessary. To check the function of the constant-level oiler (1), slowly drain some oil via the screw plug (4) until air bubbles can be seen in the oil reservoir.
8.
NOTE
An excessively high oil level can lead to a temperature rise and to leakage of the fluid handled or oil.
6.1.3 Shaft seal Shaft seals are fitted prior to delivery. Observe the instructions on dismantling( Section 7.4.6 Page 50) or reassembly( Section 7.5.3 Page 54). Reservoir of nonpressurised external fluid Double mechanical seal External liquid feed If applicable, fill the reservoir of non-pressurised external fluid in accordance with the general arrangement drawing. Prior to starting up the pump, apply barrier pressure as specified in the general arrangement drawing. Apply the quantities and pressures specified in the data sheet and the general arrangement drawing. 6.1.4 Priming and venting the pump
DANGER
Risk of potentially explosive atmosphere as a result of incompatible liquids mixing in auxiliary piping Risk of burns! Explosion hazard! Make sure barrier/quench liquid is compatible with the fluid handled.
DANGER
Risk of potentially explosive atmosphere inside the pump Explosion hazard! The pump internals in contact with the fluid to be handled, including the seal chamber and auxiliary systems must be filled with the fluid to be handled at all times. Provide sufficient inlet pressure. Provide an appropriate monitoring system.
CPKN
33 of 70
DANGER
Shaft seal failure caused by insufficient lubrication Hot or toxic fluid could escape! Damage to the pump! Before starting up the pump set, vent the pump and suction line and prime both with the fluid to be handled. 1. 2. 3. Vent the pump and suction line and prime both with the fluid to be handled. Fully open the shut-off element in the suction line. Fully open all auxiliary connections (barrier fluid, flushing liquid, etc).
6.1.5 Final check 1. 2. 3. 4. 5. Remove the coupling guard and the footboard for the coupling guard, if any. Check the coupling alignment; re-align the coupling if required.( Section 5.6 Page 27) Check that the coupling and shaft can easily be rotated by hand. Re-install the coupling guard and the footboard for the coupling guard, if any. Check the distance between the coupling and coupling guard. The coupling and coupling guard must not come into contact.
6.1.6 Water cooling
CAUTION
Deposit-forming, aggressive cooling water Damage to the pump! Observe the cooling water quality. Observe the following quality data of the cooling water: Not deposit forming Not aggressive Free from suspended solids Hardness on average 5 dH (~1 mmol/l) pH > 8 Conditioned and neutral with regard to mechanical corrosion Inlet temperature tin=10 to 30 C Outlet temperature tout= 45 C (max.) 6.1.7 Cooling of the shaft seal
CAUTION
Vaporisation pressure of fluid handled higher than atmospheric pressure Damage to the shaft seal/pump! Cool the shaft seal. Provide sufficient quantities of cooling liquid (see table).
NOTE
The vaporisation pressure varies depending on the fluid handled, the system pressure and the material of the shaft seal (e.g. hot water).
34 of 70
CPKN
Table 13: Cooling of the shaft seal5) Bearing bracket UP02 UP03 UP04 UP05 UP06 P08s 6.1.8 Heating The space between discharge cover and bearing bracket lantern can be used as a heating chamber, if necessary. It can be fed with hot water, steam or thermal oil, especially in combination with internal circulation. Cooling liquid quantity in l/min at a product temperature of Standard design up to 250 C 3 4 5 5 6 7 up to 400 C 4 5 6 6 7 8 "K" design up to 250 C 3 4 4 5 5 6 up to 400 C 4 5 5 6 6 7
DANGER
Excessive surface temperature Explosion hazard! Risk of burns! Observe the permissible temperature classes.( Section 2.10.2 Page 11)
CAUTION
Lack of heating medium Damage to the pump! Provide sufficient quantities of a suitable heating medium.
CAUTION
Time for warming up the pump too short Damage to the pump! Check that the pump is sufficiently warmed up throughout.
CAUTION
Impermissibly high temperature of the heating medium Fluid or heating medium could escape! Observe the application limits of the heating media. Table 14: Temperature limits for heating with hot water or thermal oil Design Hot water / saturated steam tmax [C] Standard design; lantern JL 1040 6), O-ring EPDM Lantern JS 1025 7); profile joint PTFE/steel alloy Welded casing cover 183 250 300 pmax [bar] 10 20 20 300 300 Thermal oil tmax [C] pmax [bar] 6 6
5) 6) 7)
Not possible for conical seal chamber "A". GJL-250 to EN 1561 GJS-400-18-LT to EN 1563
CPKN
35 of 70
6.1.9 Heating up/keeping warm the pump (set)
CAUTION
Pump blockage Damage to the pump! Prior to pump start-up, heat up the pump as described in the manual. Observe the following when heating up the pump (set) and keeping it warm: Make sure the temperature is increased continuously. Max. heating speed: 10 C/min (10 K/min) Fluid temperatures above 150 C Temperature difference If the pump is used for handling fluids with fluid temperatures exceeding 150 C, make sure that the pump has been sufficiently heated throughout before starting it up. The temperature difference between the pump's surface and the fluid handled must not exceed 100 C (100 K) when the pump is started up. 6.1.10 Start-up
DANGER
Non-compliance with the permissible pressure and temperature limits if the pump is operated with the suction and/or discharge line closed. Explosion hazard! Leakage of hot or toxic fluids! Never operate the pump with the shut-off elements in the suction line and/or discharge line closed. Only start up the pump set with the discharge-side shut-off element slightly or fully open.
DANGER
Excessive temperatures due to dry running or excessive gas content in the fluid handled Explosion hazard! Damage to the pump set! Never operate the pump set without liquid fill. Prime the pump as specified.( Section 6.1.4 Page 33) Always operate the pump within the permissible operating range.
CAUTION
Abnormal noises, vibrations, temperatures or leakage Damage to the pump! Switch off the pump (set) immediately. Eliminate the causes before returning the pump set to service. The system piping has been cleaned. The pump, suction line and, if applicable, inlet tank have been vented and primed with the fluid to be handled. The lines for priming and venting have been closed.
36 of 70
CPKN
CAUTION
Start-up against open discharge line Motor overload! Make sure the motor has sufficient power reserves. Use a soft starter. Use speed control. 1. 2. 3. 4. Fully open the shut-off element in the suction head/suction lift line. Close or slightly open the shut-off element in the discharge line. Start up the motor. Immediately after the pump has reached full rotational speed, slowly open the shut-off element in the discharge line and adjust it to comply with the duty point.
CAUTION
Misalignment of pump and coupling Damage to pump, motor and coupling! When the operating temperature has been reached, switch off the pump set and check the coupling alignment. 5. Check the coupling alignment and re-align the coupling, if required.
6.1.11 Checking the shaft seal Mechanical seal Gland packing The mechanical seal only leaks slightly or invisibly (as vapour) during operation. Mechanical seals are maintenance-free. The gland packing must drip slightly during operation.
DANGER
Impermissibly high temperatures at gland packings Explosion hazard! Always use suitable temperature monitoring for gland packings. Gland packing must be tightened correctly. Pure graphite packing If a pure graphite packing is used, there must always be some leakage. Table 15: Leakage rate of the pure graphite packing Quantity Minimum Maximum Adjusting the leakage Prior to commissioning 1. 2. Only lightly tighten the nuts of the gland follower by hand. Use a feeler gauge to verify that the gland follower is mounted centred and at a right angle to the shaft. Values 10 cm/min 20 cm/min
The gland must leak after the pump has been primed. After five minutes of operation
WARNING
Unprotected rotating parts Risk of personal injury! Do not touch rotating parts. When the pump is running, perform any work with utmost caution. The leakage can be reduced. 1. Tighten the nuts on the gland follower by 1/6 turn.
CPKN
37 of 70
2.
Monitor the leakage for another five minutes.
Excessive leakage: Repeat steps 1 and 2 until the minimum value has been reached. Not enough leakage: Slightly loosen the nuts at the gland follower. No leakage: Immediately switch off pump set! Loosen gland follower and repeat commissioning. Checking the leakage After the leakage has been adjusted, monitor the leakage for about two hours at maximum fluid temperature. Check that enough leakage occurs at the gland packing at minimum fluid pressure. 6.1.12 Shutdown The shut-off element in the suction line is and remains open. On pump sets with double mechanical seal, apply the required pressure specified in the general arrangement drawing to the mechanical seal chamber also during standstill. Also ensure quench liquid supply is ON during pump standstill. 1. 2. Close the shut-off element in the discharge line. Switch off the motor and make sure the pump set runs down smoothly to a standstill.
NOTE
If the discharge line is equipped with a non-return or check valve, the shut-off element in the discharge line may remain open, provided the site's requirements and regulations are taken into account and observed.
NOTE
If shut-off is not possible, the pump will run in reverse direction. The reverse runaway speed must be lower than the rated speed. For prolonged shutdown periods: 1. 2. Close the shut-off element in the suction line. Close the auxiliary connections. If the fluid to be handled is fed in under vacuum, also supply the shaft seal with barrier fluid during standstill. Only turn off the cooling liquid supply after the pump has cooled down.
CAUTION
Risk of freezing during prolonged pump shutdown periods Damage to the pump! Drain the pump and the cooling/heating chambers (if any) or otherwise protect them against freezing.
38 of 70
CPKN
6.2 Operating limits
DANGER
Non-compliance with operating limits for pressure, temperature, fluid handled and speed Explosion hazard! Hot or toxic fluid could escape! Comply with the operating data indicated in the data sheet. Never use the pump for handling fluids it is not designed for. Avoid prolonged operation against a closed shut-off element. Never operate the pump at temperatures, pressures or rotational speeds exceeding those specified in the data sheet or on the name plate unless the written consent of the manufacturer has been obtained.
6.2.1 Ambient temperature
CAUTION
Operation outside the permissible ambient temperature Damage to the pump (set)! Observe the specified limits for permissible ambient temperatures. Observe the following parameters and values during operation: Table 16: Permissible ambient temperatures Permissible ambient temperature Maximum Minimum 6.2.2 Frequency of starts Value 40 C See data sheet.
DANGER
Excessive surface temperature of the motor Explosion hazard! Damage to the motor! In case of explosion-proof motors, observe the frequency of starts specified in the manufacturer's product literature. The frequency of starts is usually determined by the maximum temperature increase of the motor. This largely depends on the power reserves of the motor in steadystate operation and on the starting conditions (DOL, star-delta, moments of inertia, etc). If the start-ups are evenly spaced over the period indicated, the following limits can be used for orientation for start-up with the discharge-side gate valve slightly open: Table 17: Frequency of starts Motor rating [kW] up to 12 up to 100 more than 100 Maximum number of start-ups [Start-ups/hour] 15 10 5
CAUTION
Re-starting while motor is still running down Damage to the pump (set)! Do not re-start the pump set before the pump rotor has come to a standstill.
CPKN
39 of 70
6.2.3 Fluid handled 6.2.3.1 Flow rate Unless specified otherwise in the characteristic curves or in the data sheets, the following applies: Short-time operation: Qmin8) = 0.1 Qopt 9) Continuous operation: Qmin8) = 0.3 Qopt 9) 2-pole operation: Qmax10) = 1.1 Qopt 9) 4-pole operation: Qmax10) = 1.25 Qopt9) The data refer to water and water-like fluids. Longer operating periods with these fluids and at the flow rates indicated will not cause an additional increase in the temperatures on the pump surface. However, if the physical properties of the fluids handled are different from water, the calculation formula below must be used to check if an additional heat build-up may lead to a dangerous temperature increase at the pump surface. If necessary, the minimum flow must be increased.

Table 18: Key Symbol c g H Tf To
Description Specific heat capacity Gravitational constant Pump head Temperature of the fluid handled Temperature at the casing surface Pump efficiency at duty point Temperature difference
Unit J/kg K m/s m C C K
6.2.3.2 Density of the fluid handled The power input of the pump increases in proportion to the density of the fluid handled.
CAUTION
Impermissibly high density of the fluid handled Motor overload! Observe the information on fluid density indicated in the data sheet. Make sure the motor has sufficient power reserves.
6.2.3.3 Abrasive fluids Do not exceed the maximum permissible solids content specified in the data sheet. When the pump handles fluids containing abrasive substances, increased wear of the hydraulic system and shaft seal are to be expected. In this case, reduce the commonly recommended inspection intervals.
8) 9) 10)
Minimum permissible flow rate Flow rate at best efficiency point Maximum permissible flow rate
40 of 70
CPKN
6.3 Shutdown/storage/preservation
6.3.1 Measures to be taken for shutdown The pump (set) remains installed Sufficient fluid is supplied for the operation check run of the pump. Start up the pump (set) regularly between once a month and once every three months for approximately five minutes during prolonged shutdown periods. This will prevent the formation of deposits within the pump and the pump intake area. The pump (set) is removed and stored 1. The pump has been properly drained( Section 7.3 Page 48) and the safety instructions for dismantling the pump have been observed.( Section 7.4.1 Page 48) 1. 2. 3. Spray-coat the inside wall of the pump casing, and in particular the impeller clearance areas, with a preservative. Spray the preservative through the suction and discharge nozzles. It is advisable to then close the pump nozzles (e.g. with plastic caps or similar). Oil or grease all exposed machined parts and surfaces of the pump (with silicone-free oil or grease, food-approved, if required) to protect them against corrosion. Observe the additional instructions.( Section 3.3 Page 14)
If the pump set is to be stored temporarily, only preserve the wetted components made of low-alloy materials. Commercially available preservatives can be used for this purpose. Observe the manufacturer's instructions for application/removal. Observe any additional instructions and information provided.( Section 3 Page 13)
6.4 Returning to service

For returning the pump to service observe the sections on commissioning/start-up ( Section 6.1 Page 32) and the operating limits.( Section 6.2 Page 39) In addition, carry out all servicing/maintenance operations before returning the pump (set) to service.( Section 7 Page 42)
WARNING
Failure to re-install or re-activate protective devices Risk of personal injury from moving parts or escaping fluid! As soon as the work is complete, re-install and/or re-activate any safety-relevant and protective devices.
NOTE
If the pump has been out of service for more than one year, replace all elastomer seals.
CPKN
41 of 70
7 Servicing/Maintenance
7.1 Safety regulations
DANGER
Sparks produced during servicing work Explosion hazard! Observe the safety regulations in force at the place of installation! Always perform maintenance work on explosion-proof pump sets outside potentially explosive atmospheres.
DANGER
Improperly serviced pump set Explosion hazard! Damage to the pump set! Service the pump set regularly. Prepare a maintenance schedule with special emphasis on lubricants, shaft seal and coupling. The operator ensures that all maintenance, inspection and installation work is performed by authorised, qualified specialist personnel who are thoroughly familiar with the manual.
WARNING
Unintentional starting of pump set Risk of injury by moving parts! Make sure that the pump set cannot be started up unintentionally. Always make sure the electrical connections are disconnected before carrying out work on the pump set.
WARNING
Fluids and supplies posing a health hazard and/or hot fluids or supplies Risk of injury! Observe all relevant laws. When draining the fluid take appropriate measures to protect persons and the environment. Decontaminate pumps which handle fluids posing a health hazard.
WARNING
Insufficient stability Risk of crushing hands and feet! During assembly/dismantling, secure the pump (set)/pump parts to prevent tipping or falling over. A regular maintenance schedule will help avoid expensive repairs and contribute to trouble-free, reliable operation of the pump (set) with a minimum of maintenance expenditure and work.
NOTE
All maintenance, service and installation work can be carried out by KSB Service or authorised workshops. Find your contact in the attached "Addresses" booklet or on the Internet at "www.ksb.com/contact". Never use force when dismantling and reassembling the pump set.
42 of 70
CPKN
7.2 Maintenance/inspection
7.2.1 Supervision of operation
DANGER
Excessive temperatures as a result of bearings running hot or defective bearing seals Explosion hazard! Fire hazard! Damage to the pump set! Risk of burns! Regularly check the lubricant level. Regularly check the rolling element bearings for running noises.
DANGER
Incorrectly serviced shaft seal Explosion hazard! Leakage of hot, toxic fluids! Damage to the pump set! Risk of burns! Fire hazard! Regularly service the shaft seal.
DANGER
Incorrectly serviced barrier fluid system Explosion hazard! Fire hazard! Damage to the pump set! Hot and/or toxic fluids could escape! Service the barrier fluid system regularly. Monitor the barrier fluid pressure.
CAUTION
Increased wear due to dry running Damage to the pump set! Never operate the pump set without liquid fill. Never close the shut-off element in the suction line and/or supply line during pump operation.
CAUTION
Impermissibly high temperature of fluid handled Damage to the pump! Prolonged operation against a closed shut-off element is not permitted (heating up of the fluid). Observe the temperature limits in the data sheet and in the section on operating limits.( Section 6.2 Page 39) While the pump is in operation, observe and check the following: The pump must run quietly and free from vibrations at all times. In case of oil lubrication, ensure the oil level is correct.( Section 6.1.2 Page 32) Check the shaft seal.( Section 6.1.11 Page 37) Check the static seals for leakage.
CPKN
43 of 70
Check the rolling element bearings for running noises. Vibrations, noise and an increase in current input occurring during unchanged operating conditions indicate wear. Monitor the correct functioning of any auxiliary connections. Cooling system Take the pump out of service at least once a year to thoroughly clean the cooling system. Monitor the stand-by pump. To make sure that stand-by pumps are ready for operation, start them up once a week. Monitor the bearing temperature. The bearing temperature must not exceed 90 C (measured on the outside of the bearing bracket).
CAUTION
Operation outside the permissible bearing temperature Damage to the pump! The bearing temperature of the pump (set) must never exceed 90 C (measured on the outside of the bearing bracket).
NOTE
After commissioning, increased temperatures may occur at grease-lubricated rolling element bearings due to the running-in process. The final bearing temperature is only reached after a certain period of operation (up to 48 hours depending on the conditions).
7.2.2 Inspection work
DANGER
Excessive temperatures caused by friction, impact or frictional sparks Explosion hazard! Fire hazard! Damage to the pump set! Regularly check the coupling guard, plastic components and other guards of rotating parts for deformation and sufficient distance from rotating parts.
7.2.2.1 Checking the coupling Check the flexible elements of the coupling. Replace the relevant parts in due time if there is any sign of wear and check the alignment. 7.2.2.2 Checking the clearances Remove the back pull-out unit to be able to check the clearances.( Section 7.4.4 Page 49) If the clearance is larger than permitted (see the following table), replace casing wear ring 502.01 with a new one. The clearances given refer to the diameter. Table 19: Clearances between impeller and casing / between impeller and casing wear ring Nominal diameter of the discharge nozzle up to DN 65 DN 80 to DN 200 DN 250 and above CPKN-S1/-S2 0.40 mm + 0.1 0.50 mm + 0.1 0.65 mm + 0.1 CPKN-C1/-C1.V/-C3.1/-C3.2 CPKN-E 0.60 mm + 0.1 0.60 mm + 0.1 0.75 mm + 0.1
44 of 70
CPKN
These values are valid for temperatures up to 250 C; for temperatures higher than 250 the clearance is increased by 0.1 to 0.2 mm
NOTE
If the clearances given are exceeded by more than 1 mm (referring to the diameter) replace the affected components or restore the original clearance by means of a casing wear ring. Contact KSB.
7.2.2.3 Cleaning filters
CAUTION
Insufficient inlet pressure due to clogged filter in the suction line Damage to the pump! Monitor contamination of filter with suitable means (e.g. differential pressure gauge). Clean filter at appropriate intervals.
7.2.3 Lubrication and lubricant change of rolling element bearings
DANGER
Excessive temperatures as a result of bearings running hot or defective bearing seals Explosion hazard! Fire hazard! Damage to the pump set! Regularly check the condition of the lubricant.
7.2.3.1 Oil lubrication The rolling element bearings are usually lubricated with mineral oil. 7.2.3.1.1 Intervals Table 20: Oil change intervals Temperature at the bearing up to 70 70 C - 80 C 80 C - 90 C 7.2.3.1.2 Oil quality Table 21: Oil quality Symbol to DIN 51502 CLP46 lubricating oil to DIN 51517 or HD 20W/20 SAE Designation Properties Kinematic viscosity at 40 C Flash point (to Cleveland) 464 mm/s +175 All subsequent oil changes11) After 300 operating hours Every 8500 operating hours After 300 operating hours Every 4200 operating hours After 300 operating hours Every 2000 operating hours First oil change
11)
At least once a year
CPKN
45 of 70
Designation
Symbol to DIN 51502
Properties Solidification point (pour point) Application temperature12) -15 Higher than permissible bearing temperature
7.2.3.1.3 Oil quantity Table 22: Oil quantity Bearing bracket UP02 UP03 UP04 UP05 UP06 P08s 7.2.3.1.4 Changing the oil Oil quantity [l] 0.3 0.5 0.5 1.5 1.4 4.5
WARNING
Lubricants posing a health hazard and/or hot lubricants Hazard to persons and the environment! When draining the lubricant take appropriate measures to protect persons and the environment. Wear safety clothing and a protective mask, if required. Collect and dispose of any lubricants. Observe all legal regulations on the disposal of fluids posing a health hazard.
1
1 3 1. 2. 3. 4.
3
2 Screw plug
Fig. 15: Bearing bracket with constant-level oiler Constant-level oiler Bearing bracket
A suitable container for the used oil is on hand. Place the container underneath the screw plug. Undo the screw plug (2) at the bearing bracket (3) and drain the oil. Once the bearing bracket (3) has been drained, re-insert and re-tighten the screw plug (2). Re-fill with oil.( Section 6.1.2 Page 32)
12)
For ambient temperatures below -10 C use a different suitable type of lubricating oil. Contact KSB.
46 of 70
CPKN
7.2.3.2 Grease lubrication The bearings are supplied packed with high-quality lithium-soap grease. 7.2.3.2.1 Intervals The bearings are re-lubricated via the lubricating nipples, see the following drawing.
Fig. 16: Position of lubricating nipples 1 Lubricating nipple 2 Lubricating nipple
CAUTION
Contaminated lubricating nipples Contamination of the lubricating grease! Clean the grease lubricating nipples before using them for re-lubrication. Re-lubrication After approx. 5,000 operating hours At least once a year Required grease quantity( Section 7.2.3.2.3 Page 47) Grease change After 16,000 operating hours At least every 2 years Required grease quantity( Section 7.2.3.2.3 Page 47) Under unfavourable operating conditions (e.g. high room temperature, high atmospheric humidity, dust laden air, aggressive industrial atmosphere) check the bearings earlier and clean and re-lubricate them, if required. 7.2.3.2.2 Grease quality Table 23: Grease quality to DIN 51825 Soap basis Lithium NLGI grade 2 to 3 Worked penetration at 25 C in mm/10 220-295 Drop point 175 C Temperature range -30 C to 120 C
7.2.3.2.3 Grease quantities Table 24: Grease quantities for re-lubrication and re-filling Bearings Re-lubrication Pump-end bearing UP02 UP03 UP04 UP05 7.5 g / 8.5 cm 12.5 g / 14 cm 12.5 g / 14 cm 17.5 g / 20 cm Drive-end bearing 15 g / 17 cm 25 g / 28 cm 25 g / 28 cm 35 g / 40 cm Re-fill Bearing+cover, pump end approx. 10 g / 11 cm approx. 25 g / 28 cm approx. 25 g / 28 cm approx. 40 g / 45 cm Bearing+cover, drive end approx. 30 g / 33 cm approx. 60 g / 67 cm approx. 60 g / 67 cm approx. 80 g / 90 cm
CPKN
47 of 70
Bearings
Re-lubrication Pump-end bearing Drive-end bearing 70 g / 80 cm 70 g / 80 cm
Re-fill Bearing+cover, pump end approx. 80 g / 90 cm approx. 80 g / 90 cm Bearing+cover, drive end approx. 205 g / 225 cm approx. 205 g / 225 cm
UP06 P08
35 g / 40 cm 35 g / 40 cm
7.2.3.2.4 Changing the grease
CAUTION
Mixing greases of differing soap bases Changed lubricating qualities! Thoroughly clean the bearings. Adjust the re-lubrication intervals to the grease used. The pump has been dismantled for changing the grease.( Section 7.4 Page 48) 1. 2. Only half-fill the bearing cavities with grease. Fill the cavities in the bearing cover until they are about 1/3 full.
7.3 Drainage/cleaning
WARNING
Fluids and supplies posing a health hazard and/or hot fluids and supplies Hazard to persons and the environment! Collect and properly dispose of flushing medium and any residues of the fluid handled. Wear safety clothing and a protective mask, if required. Observe all legal regulations on the disposal of fluids posing a health hazard. If the fluids handled by the pump (set) leave residues which might lead to corrosion damage when coming into contact with atmospheric humidity, or which might ignite when coming into contact with oxygen, the pump set must be flushed through, neutralised, and anhydrous inert gas must be blown through the pump for drying purposes. Use connection 6B to drain the fluid handled (see auxiliary connections).
7.4 Dismantling the pump set

7.4.1 General information/Safety regulations
WARNING
Unqualified personnel performing work on the pump (set) Risk of injury! Always have repair and maintenance work performed by specially trained, qualified personnel.
WARNING
Hot surface Risk of injury! Allow the pump set to cool down to ambient temperature.
48 of 70
CPKN
WARNING
Improper lifting/moving of heavy assemblies or components Personal injury and damage to property! Use suitable transport devices, lifting equipment and lifting tackle to move heavy assemblies or components. Observe the general safety instructions and information.( Section 7 Page 42) For any work on the motor, observe the instructions of the relevant motor manufacturer. For dismantling and reassembly refer to the general assembly drawing.( Section 9.1 Page 62) In the event of damage you can always contact our service staff.
DANGER
Insufficient preparation of work on the pump (set) Risk of injury! Properly shut down the pump set.( Section 6.1.12 Page 38) Close the shut-off elements in suction and discharge line. Drain the pump and release the pump pressure. ( Section 7.3 Page 48) Close any auxiliary connections. Allow the pump set to cool down to ambient temperature.
7.4.2 Preparing the pump set 1. 2. 3. 4. 5. Interrupt the power supply and secure the pump against unintentional start-up. Disconnect and remove all auxiliary pipework. Remove the coupling guard. Remove the coupling spacer, if any. Drain the oil fill of oil-lubricated bearings.( Section 7.2.3.1.4 Page 46)
7.4.3 Dismantling the motor
NOTE
On pump sets with spacer-type couplings, the back pull-out unit can be removed while the motor remains bolted to the baseplate.
WARNING
Motor tipping over Risk of crushing hands and feet! Suspend or support the motor to prevent it from tipping over. 1. 2. 3. Disconnect the motor from the power supply. Unbolt the motor from the baseplate. Shift the motor to separate it from the pump.
7.4.4 Removing the back pull-out unit Pumps without spacer-type coupling: the motor has been removed.
CPKN
49 of 70
WARNING
Back pull-out unit tipping over Risk of crushing hands and feet! Suspend or support the bearing bracket at the pump end. 1. 2. 3. 4. 5. 6. If required, suspend or support bearing bracket 330 to prevent it from tipping over. Unbolt support foot 183 from the baseplate. Undo hexagon nut 920.01 at the volute casing. Pull the back pull-out unit out of the volute casing. Remove and dispose of joint ring 411.10. Place the back pull-out unit on a clean and level surface.
7.4.5 Removing the impeller The notes and steps stated in( Section 7.4.1 Page 48) to( Section 7.4.4 Page 49) have been observed/carried out. The back pull-out unit is kept in a clean and level assembly area. 1. 2. 3. 4. 5. Undo impeller nut 922 (right-hand thread). Remove impeller 230 with an impeller removal device. Place impeller 230 on a clean and level surface. Remove keys 940.01 from shaft 210. Remove and dispose of joint rings 411.31/411.32.
7.4.6 Removing the shaft seal 7.4.6.1 Dismantling the mechanical seal - cylindrical casing cover The notes and steps stated in( Section 7.4.1 Page 48) to( Section 7.4.5 Page 50) have been observed/carried out. The back pull-out unit is kept in a clean and level assembly area. 1. 2. 3. 4. Undo hexagon nuts 920.02 and push back seal cover 471.01 (if fitted) until it rests against thrower 507.01. Remove casing cover 161 with O-ring 412.01. Remove and dispose of O-ring 412.01. Pull complete mechanical seal 433 with shaft protecting sleeve 524.01, seal cover 471 and thrower 507.01 off shaft 210.
7.4.6.2 Dismantling the mechanical seal - conical casing cover The notes and steps stated in( Section 7.4.1 Page 48) to( Section 7.4.5 Page 50) have been observed/carried out. The back pull-out unit is kept in a clean and level assembly area. 1. 2. 3. 4. Pull shaft sleeve 524.01 with the rotating assembly of mechanical seal 433 off the shaft. Dismantle casing cover 161 with the stationary ring of mechanical seal 433. Remove thrower 507.01. Press the stationary ring of mechanical seal 433 out of casing cover 161.
7.4.6.3 Dismantling the packed gland The notes and steps stated in( Section 7.4.1 Page 48) to( Section 7.4.5 Page 50) have been observed/carried out.
50 of 70
CPKN
The back pull-out unit is kept in a clean and level assembly area. 1. 2. 3. 4. 5. 6. Unscrew hexagon nuts 920.02 at gland follower 452 and remove the gland follower. Remove stuffing box ring 454.01 and drip plate 463.01. Remove casing cover 161 with O-ring 412.01 and gland packing 461.01. Remove packing rings 461.01 and lantern ring 458.01, if any, from the packing chamber. Pull off guard 680. Pull shaft protecting sleeve 524.01 and thrower 507.01 off shaft 210.
7.4.7 Dismantling the bearings The notes and steps stated in( Section 7.4.1 Page 48) to( Section 7.4.6 Page 50) have been observed/carried out. The bearing bracket is kept in a clean and level assembly area. 1. 2. 3. 4. 5. 6. 7. 8. Unscrew hexagon nuts 920.04 at the flange of bearing bracket lantern 344. Remove bearing bracket lantern 344. Unscrew the hexagon socket head cap screw in the coupling hub. Pull the coupling half off the pump shaft with a puller. Remove key 940.02. Undo screws 914.02 and remove drive-end bearing cover 360.02 and joint ring 400.02. Undo screws 914.01 and remove pump-end bearing cover 360.01 and joint ring 400.01. Carefully drive shaft 210 together with angular contact ball bearing 320.02 and the inner ring of cylindrical roller bearing 322.01 out of the bearing bracket towards the drive end. Remove support disc 550.23 of angular contact ball bearing 320.02 from bearing bracket 330.
9.
10. In case of grease lubrication, remove disc 550.25. 11. Remove cylindrical roller bearing 322.01 (roller cage) from bearing bracket 330. 12. In case of grease lubrication, remove disc 550.24. 13. Bend open lockwasher 931.01 behind keywayed nut 920.21 on shaft 210. 14. Unscrew keywayed nut 920.21 (right-hand thread) and remove lockwasher 931.01.
WARNING
Hot surfaces due to heating of components for assembly/dismantling Risk of burns! Wear heat-resistant protective gloves. Remove flammable substances from the danger zone. 15. Heat up angular contact ball bearing 320.02 and the inner ring of cylindrical roller bearing 322.01 to 80 C, and pull them off shaft 210. 16. Dispose of joint rings 400.01/.02.
CPKN
51 of 70
7.5 Reassembling the pump set

7.5.1 General information/Safety regulations
WARNING
Improper lifting/moving of heavy assemblies or components Personal injury and damage to property! Use suitable transport devices, lifting equipment and lifting tackle to move heavy assemblies or components.
CAUTION
Improper reassembly Damage to the pump! Reassemble the pump (set) in accordance with the general rules of sound engineering practice. Use original spare parts only. Sequence Sealing elements Always reassemble the pump in accordance with the corresponding general assembly drawing. Gaskets Always use new gaskets, making sure that they have the same thickness as the old ones. Always fit gaskets of asbestos-free materials or graphite without using lubricants (e.g. copper grease, graphite paste). O-rings Never use O-rings that have been glued together from material sold by the metre.
CAUTION
Contact of O-ring with graphite or similar material Fluid could escape! Do not coat O-ring with graphite or similar material. Use animal fats or lubricants based on silicone or PTFE. Assembly adhesives For gaskets, avoid the use of assembly adhesives, if possible. If assembly adhesives are required, use a commercially available contact adhesive (e.g. "Pattex"). Only apply adhesive at selected points and in thin layers. Never use quick-setting adhesives (cyanoacrylate adhesives). Coat the locating surfaces of the individual components and screwed connections with graphite or similar before reassembly. Tightening torques For reassembly, tighten all screws and bolts as specified in this manual.( Section 7.6 Page 57) 7.5.2 Installing the bearings The individual parts are kept in a clean and level assembly area. All dismantled parts have been cleaned and checked for wear. Any damaged or worn parts have been replaced by original spare parts. The sealing surfaces have been cleaned.
52 of 70
CPKN
WARNING
Hot surfaces due to heating of components for assembly/dismantling Risk of burns! Wear heat-resistant protective gloves. Remove flammable substances from the danger zone. 1. 2. Heat up angular contact ball bearing 320.02 and the inner ring of cylindrical roller bearing 322.01 to approx. 80 in an oil bath. Push angular contact ball bearing 320.02 and the inner ring of cylindrical roller bearing 322.01 onto shaft 210 until they will not go any further.
NOTE
Angular contact ball bearings must be installed in back-to-back arrangement. Angular contact ball bearings installed in pairs must always be from the same manufacturer. 3. 4. 5. 6. 7. 8. 9. Use a C-spanner to tighten keywayed nut 920.21 without lockwasher 931.01. Let angular contact ball bearing 320.01 cool down to approximately 5 C above ambient temperature. Re-tighten keywayed nut 920.21, then unscrew it again. Apply a few spots of a suitable lubricant (e.g. Molykote) to the contact faces of lockwasher 931.01 and keywayed nut 920.21. Fit lockwasher 931.01. Tighten keywayed nut 920.21. Bend back lockwasher 931.01.
10. Insert circlip 932.01/932.02 into the bearing bracket. 11. In case of grease lubrication, insert disc 550.24. 12. Fit cylindrical roller bearing 322.01 (roller cage) in the bearing bracket.
Fig. 17: Fitting the bearings 13. In case of grease lubrication, insert disc 550.25. 14. Insert support disc 550.23 of angular contact ball bearing 320.02 into bearing bracket 330. 15. In case of grease lubrication, fill the bearings and bearing covers with grease. Grease lubrication( Section 7.2.3.2 Page 47) 16. Carefully push pre-assembled shaft 210 with angular contact ball bearing 320.02 and the inner ring of cylindrical roller bearing 322.01 from the drive end into bearing bracket 330. 17. Fit pump-end bearing cover 360.01 with joint ring 400.01; take care not to damage lip seal 421.01. 18. Fit drive-end bearing cover 360.02 with joint ring 400.02; take care not to damage lip seal 421.02.
CPKN
53 of 70
19. Fit bearing bracket lantern 344. 20. Tighten hexagon nuts 920.04 at the flange of bearing bracket 330. 21. Fit keys 940.02. 22. Pull the coupling hub onto the shaft end. 23. Secure the coupling hub with a set screw. 24. Fit thrower 507.01, if any. 7.5.3 Fitting the shaft seal 7.5.3.1 Mechanical seal The following rules must be observed when installing the mechanical seal: For installing the mechanical seal, proceed as shown in the seal installation drawing. Work cleanly and accurately. Only remove the protective wrapping of the contact faces immediately before installation takes place. Prevent any damage to the sealing surfaces or O-rings. After inserting the stationary ring, check that it is plane-parallel in relation to the casing part. The surface of the shaft protecting sleeve must be absolutely clean and smooth, and the sleeve's mounting edge must be chamfered. When sliding the rotating assembly onto the shaft protecting sleeve, take appropriate steps to protect the surface of the shaft protecting sleeve from damage. Re-installing the mechanical seal - cylindrical casing cover The notes and steps stated in( Section 7.5.1 Page 52) to( Section 7.5.2 Page 52) have been observed/carried out. The bearing assembly and the individual parts of mechanical seal 433 are kept in a clean and level assembly area. All dismantled parts have been cleaned and checked for wear. Any damaged or worn parts have been replaced by original spare parts. The sealing surfaces have been cleaned. 1. 2. 3. 4. 5. Slide thrower 507.01 (if any) onto shaft 210 from the pump end. Fasten seal cover 471 with inserted O-ring and the stationary ring of the mechanical seal to casing cover 161 with hexagon nut 920.02. Insert casing cover 161 with O-ring 412.01 into lantern 344; watch joint ring 411.11. Fit the rotating assembly of mechanical seal 433 on shaft protecting sleeve 524.01 (observe distance B - see Supplementary Sheet of the mechanical seal).
Slide pre-assembled mechanical seal 433 and shaft protecting sleeve 524.01 onto shaft 210. Fitting the mechanical seal - conical casing cover The notes and steps stated in( Section 7.5.1 Page 52) to( Section 7.5.2 Page 52) have been observed/carried out. The bearing assembly and the individual parts of mechanical seal 433 are kept in a clean and level assembly area. All dismantled parts have been cleaned and checked for wear. Any damaged or worn parts have been replaced by original spare parts. The sealing surfaces have been cleaned. 1. Slide thrower 507.01 (if any) onto shaft 210 from the pump end.
54 of 70
CPKN
2. 3. 4.
Carefully press the stationary ring of mechanical seal 433 with O-ring into casing cover 161. Fit casing cover 161 with the inserted stationary ring of the mechanical seal into lantern 344. Fit the rotating assembly of mechanical seal 433 and the spacer ring, if any, on shaft protecting sleeve 524.01 (observe distance B - see Supplementary Sheet for the mechanical seal). Slide pre-assembled mechanical seal 433 and shaft protecting sleeve 524.01 onto shaft 210.
5.
7.5.3.2 Packing the gland
a)
l
b)
l
da
d1
da
d1
Fig. 18: Gland packing chamber a) with lantern ring and b) without lantern ring Table 25: Gland packing chamber Bearing bracket UP02 UP03 UP04 UP05 UP06 P08s Gland packing chamber d1 35 45 55 70 80 100 da 51 65 75 95 105 132 l 53 64 64 79 79 102 Packing crosssection 8x8 10 x 10 10 x 10 12.5 x 12.5 12.5 x 12.5 16 x 16 Packing rings 4 rings and 1 lantern ring OR 6 rings
Pure graphite packings see supplementary operating instructions. Always use pre-compressed packing rings. The notes and steps stated in( Section 7.5.1 Page 52) to( Section 7.5.2 Page 52) have been observed/carried out. The bearing assembly as well as the individual parts are kept in a clean and level assembly area. All disassembled parts have been cleaned and checked for wear. Any damaged or worn parts have been replaced by original spare parts. The sealing surfaces have been cleaned. 1. 2. 3. 4. 5. Clamp casing cover 161 into a vice. Push in neck bush 456.01. Insert the first packing ring, ensuring that its cut edge is in horizontal position. Hold the packing ring in place and slide shaft protecting sleeve 524 (chamfered side first) into the gland packing chamber from the pump end. Slightly expand the inside diameter of the packing ring by moving shaft protecting sleeve 524 back and forth. Then pull out the shaft protecting sleeve. Insert lantern ring 458, if any. Insert each subsequent packing ring separately with its joint offset by approx. 90 in relation to the previous one. Repeat the expansion procedure. When the last packing ring has been inserted, shaft protecting sleeve 524 remains in the packing chamber. Insert stuffing box ring 454.01 with the drilled hole down. Fit gland follower 452 and lightly fasten it by hand with the two hexagon nuts 920.02; watch discs 550.01.
6. 7.
CPKN
55 of 70
8. 9.
Fit guard 680. Install complete discharge cover 161 with shaft protecting sleeve 524 in the pump; take care not to damage joint ring 411.11.
7.5.4 Fitting the impeller The notes and steps stated in( Section 7.5.1 Page 52) to( Section 7.5.3 Page 54) have been observed/carried out. The assembled bearing/mechanical seal as well as the individual parts are kept in a clean and level assembly area. All dismantled components have been cleaned and checked for wear. Any damaged or worn parts have been replaced by original spare parts. The sealing surfaces have been cleaned. Impeller bore, shaft and keyways are clean and free from burrs. 1. 2. 3. 4. 5. 6. Insert keys 940.01 into the shaft keyway. Insert joint ring 411.32. Coat the impeller with a suitable lubricant. Slip impeller 230 onto shaft 210. Insert joint ring 411.31. Screw impeller nut 922 to shaft 210.( Section 7.6.2 Page 57)
7.5.5 Fitting the back pull-out unit
WARNING
Back pull-out unit tipping over Risk of crushing hands and feet! Suspend or support the bearing bracket at the pump end. The notes and steps stated in( Section 7.5.1 Page 52) to( Section 7.5.4 Page 56) have been observed/carried out. Any damaged or worn parts have been replaced by original spare parts. The sealing surfaces have been cleaned. For back pull-out units supplied without coupling: Fit the coupling in accordance with the manufacturer's instructions. 1. 2. 3. If required, suspend or support the back pull-out unit to prevent it from tipping over. Then slide it into volute casing 102 with a new gasket 411.10. Tighten nut 920.01 at the volute casing. Bolt support foot 183 to the baseplate.
7.5.6 Mounting the motor
NOTE
Steps 1 and 2 do not apply to versions with spacer-type coupling.
1. 2. 3. 4.
Shift the motor to connect it to the pump via the coupling. Fasten the motor to the baseplate. Align pump and motor.( Section 5.7 Page 28) Connect the motor to the power supply (refer to manufacturer's product literature).
56 of 70
CPKN
7.6 Tightening torques

7.6.1 Tightening torques Use a torque wrench to tighten the screwed connections (902.02/920.01) between the volute casing and the bearing bracket lantern. Table 26: Tightening torques for screwed connections
Material stud/hex. nut Stamp mark stud/hex. nut13) Bearing bracket lantern14) New threads15) 40 100 -15 %16) 34 85 -20 %16) 32 80 New threads15) 30 55 155 200 -15 %16) 25.5 46.7 131.7 170 -20 %16) 24 44 124 160 C35E+Qt/C 35 YK/Y A4-70/A4-70 A4-70/A4-70 Tightening torques [Nm] A B A B A B 1.7709+QT/1.7258+QT 1.6772/1.6722 GA/G
M10 M12 M16 M20
New threads15) 47 30 80 55 190 155 330 200
-15 %16) 39.9 68 161.5 280.5 25,5 46.7 131.7 170
-20 %16) 37.6 64 152 264 24 44 124 160
7.6.2 Tightening torques for the impeller nut Observe the following tightening torques for impeller nut (922): Table 27: Tightening torques for the impeller nut Bearing bracket UP02 UP03 UP04 UP05 UP06 P08s Tightening torque [Nm] 80 125 200 300 520 1000 Width across flats [mm] 22 27 32 41 55 60
Re-tighten the impeller nut some 20 to 30 minutes after assembly.
7.7 Spare parts stock

7.7.1 Ordering spare parts Always quote the following data when ordering replacement or spare parts: Type series Size KSB order number Material variant Year of construction Refer to the name plate for all data. ( Section 4.3 Page 16) Also supply the following data: Description Part No. Quantity of spare parts Shipping address
13) 14) 15) 16)
Treat unstamped screwed connections like material pair C35/E+QT/C35. A: made of toughened material - except for JL 1040; B: made of material JL 1040 These values are determined on the basis of a friction coefficient = 0.12. After repeated tightening of the threads and in case of good lubrication, reduce the values by 15 to 20 %.
CPKN
57 of 70
Mode of dispatch (freight, mail, express freight, air freight) Refer to the general assembly drawing for part numbers and descriptions. ( Section 9.1 Page 62) 7.7.2 Recommended spare parts stock for 2 years' operation to DIN 24296 Table 28: Quantity of spare parts for recommended spare parts stock Part No. Description Number of pumps (including stand-by pumps) 2 Shaft Impeller Angular contact ball bearing (set) 322.01 Cylindrical roller bearing 502.01 Casing wear ring 524.01 Shaft protecting sleeve Gaskets for pump casing (set) Torque-transmitting coupling elements (set) For variants with mechanical seal: 433 Mechanical seal complete For variants with gland packing: 456.01 Neck bush 461.01 Gland packing (set) 210 230 320.02 1 1 1 1 2 2 4 1 1 1 4 3 1 1 1 1 2 2 6 1 1 1 4 4 1 1 2 2 2 2 8 2 2 2 6 5 2 2 2 2 3 3 8 2 2 2 6 6 and 7 2 2 2 2 3 3 9 3 2 2 6 8 and 9 2 2 3 3 4 4 12 4 3 3 8 10 and more 20 % 20 % 25 % 25 % 50 % 50 % 150 % 30 % 25 % 30 % 100 %
7.7.3 Interchangeability of pump components Components featuring the same number in a column are interchangeable.
NOTE
Volute casing 102 and impeller 230 are not interchangeable between different pump sizes. Table 29: Interchangeability of pump components Description Angular contact ball bearing Shaft protecting sleeve17) Cylindrical roller bearing
Bearing bracket lantern
Stuffing box ring
Casing wear ring
Bearing bracket
Mechanical seal
Gland follower
Bearing bracket
Pump size
Part No. 320.02 322.01 502.01 507.01 524.01 471.07 452.01 454.01 456.01 458.01 1 1 1 1 1 461.01 1 1 1 1 1 161 183 210 330 344 922 433
25-160 25-200 32-125 32-160 32-200
UP02
2 3 1 2 3
2 3 1 2 3
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
2 3 1 2 3
25 25 1 1 1
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
17)
Depending on mechanical seal type
58 of 70
CPKN
Gland packing
Support foot
Casing cover
Lantern ring
Impeller nut
Neck bush
Seal cover
Thrower
Shaft
Description Angular contact ball bearing Shaft protecting sleeve17) Cylindrical roller bearing
Bearing bracket lantern
Casing wear ring
Bearing bracket
Mechanical seal
Gland follower
Stuffing box ring
Support foot
Casing cover
Bearing bracket
Pump size
Part No. 320.02 322.01 502.01 507.01 524.01 471.07 452.01 454.01 456.01 458.01 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 6 6 6 6 461.01 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 6 6 6 6 161 183 210 330 344 922 433
40-160 40-200 50-160 50-200 32-250 40-250 40-315 50-250 50-315 65-160 65-200 65-250 80-160 80-200 80-250 100-200 65-315 80-315 80-400 100-250 100-315 100-400 125-250 125-315 125-400 150-250 150-315 150-400 150-500 200-250 200-315 200-400 200-500 250-315 250-400 250-500 300-400 300-500 350-400 350-500
UP03
UP04
UP05
UP06 P08s
2 3 2 3 6 6 7 6 7 4 5 6 4 5 6 5 9 9 10 8 9 10 8 9 10 8 12 13 14 11 12 13 14 12 15 16 17 18 17 18
2 3 3 3 5 5 6 5 7 4 5 6 5 5 7 6 8 9 10 8 9 10 9 10 11 10 12 12 14 13 13 13 17 16 17 15 15 18 18 18
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 5 6 6 7 7 8 7
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 4 4 4 4 4 4
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 4 4 4 4 4 4
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 4 4 5 5 5 5
2 3 2 3 6 6 7 6 7 4 5 6 4 5 6 5 7 7 8 6 7 8 6 7 8 6 10 11 12 9 10 11 12 10 11 12 13 14 13 14
2 2 3 3 6 5 5 4 7 7 8 8 9 10 11 12 9 12 27 13 14 14 15 16 15 16 18 18 18 17 19 20 28 21 22 23 22 24 26 26
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 6 6 6 6
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 6 6 6 6
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 6 6 6 6
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 6 6 6 6
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 6 6 6 6
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 6 6 6 6
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 6 6 6 6
1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 6 6 6 6
17)
Depending on mechanical seal type
CPKN
59 of 70
Lantern ring
Neck bush
Seal cover
Shaft
Gland packing
Thrower
Impeller nut
8 Trouble-shooting
8 Trouble-shooting
WARNING
Improper remedial work on the pump (set) Risk of injury! For any work performed in order to remedy faults on the pump (set) observe the relevant information given in this operating manual or the product literature provided by the accessories manufacturers. If problems occur that are not described in the following table, consultation with KSBs customer service is required. A B C D E F G H Table 30: Trouble-shooting A B C D E F G H Possible cause Pump delivers against an excessively high pressure. Pump or piping are not completely vented or primed. Supply line or impeller clogged Formation of air pockets in the piping Suction lift is too high/NPSH available (positive suction head) is too low. Remedy 18) Re-adjust to duty point. Check system for impurities. Fit a larger impeller. 19) Increase speed (turbine, I.C. engine). Vent and/or prime. Remove deposits in the pump and/or piping. Alter piping layout. Fit vent valve. Check/alter fluid level. Install pump at a lower level. Fully open the shut-off element in the suction line. Change suction line, if the friction losses in the suction line are too high. Check any strainers installed/suction opening. Observe permissible speed of pressure fall. Clean barrier fluid duct, supply external barrier fluid, if necessary, or increase barrier fluid pressure. Replace shaft seal. Check the electrical connection of the motor and switchgear, if any. Pump delivers insufficient flow rate Motor is overloaded Excessive pump discharge pressure Increased bearing temperature Leakage at the pump Excessive leakage at the shaft seal Vibrations during pump operation Impermissible rise of temperature inside the pump
Air intake at the shaft seal
Wrong direction of rotation Speed is too low. 19)
- Increase voltage/frequency at the frequency - Operation with frequency inverter - Operation without frequency inverter inverter in the permissible range. - Check voltage. Impeller Replace worn parts by new ones. Pump back pressure is lower than Adjust duty point accurately. specified in the purchase order. In the case of persistent overloading, turn down impeller. 19) Density or viscosity of fluid handled Contact KSB. higher than stated in purchase order
18) 19)
Pump pressure must be released before attempting to remedy faults on parts which are subjected to pressure. Contact KSB.
60 of 70
CPKN
8 Trouble-shooting
A B C D E
F G H Possible cause Gland follower over-tightened or cocked Speed is too high. Defective gasket Worn shaft seal Score marks or roughness on shaft protecting sleeve / shaft sleeve Vibrations during pump operation
Remedy 18) Correct. Reduce speed. 19) Fit new gasket between volute casing and discharge cover. Fit new shaft seal. Check flushing liquid/barrier fluid. Replace shaft protecting sleeve/shaft sleeve. Fit new shaft seal. Correct suction conditions. Re-align the pump. Re-balance the impeller. Increase pressure at the pump suction nozzle. Re-align. Check the piping connections and secure fixing of pump; if required, reduce distances between the pipe clamps. Fix the pipelines using anti-vibration material. Top up, reduce or change lubricant. Correct distance according to general arrangement drawing. Replace the defective fuse. Check the electric cable connections. Clean the impeller. Re-balance the impeller. Replace. Increase minimum flow rate. Increase the free cross-section.
The pump set is misaligned. Pump warped or sympathetic vibrations in the piping Insufficient or excessive quantity of lubricant or unsuitable lubricant. Non-compliance with specified coupling distance Motor is running on two phases only. Rotor out of balance
Defective bearing Flow rate is too low. Incorrect inflow of circulation liquid
18)
Pump pressure must be released before attempting to remedy faults on parts which are subjected to pressure.
CPKN
61 of 70
9 Related Documents
9 Related Documents
9.1 General assembly drawing with list of components
230 102 903.03 411.03 524.01 412.01 903.02 411.02 411.11 344 411.10 901.31 914.01 400.01 902.04 322.01 672 920.04 330 550.23 932.02 320.02 400.02
914.02 903.18 411.18 920.21 360.02 903.04 411.04 903.16/.17 411.16/.17
210
940.02 421.02 931.01 901.04 930.01 914.04

D00462
922
502.01 561.01
183
903.01 411.01 411.31
161
411.32 940.01 561.02 902.01 920.01
903.18 411.18 507.01
638 360.01 421.01 932.01 903.46 411.46
Fig. 19: General assembly drawing of standard version (oil-lubricated)
62 of 70
CPKN
9 Related Documents
a)
550.01 920.02 463.01 902.02 458.01 452.01 680
b)
c)
411.15
471.01 902.02 920.02 561.03
456.01 454.01 461.01 648
433.02
561.03
524.01
524.01
433.02
Fig. 20: Version with gland packing (a), Mechanical seal with conical casing cover (b), Mechanical seal with cylindrical casing cover (c)
636.02 360.01 400.01 322.01 932.02 932.01 550.23 320.02 400.02 636.03 360.02
507.01 914.01
421.01
550.24
550.25
931.01 914.02
421.02
920.21
Fig. 21: Grease-lubricated version Table 31: List of components Part No. 102 Comprising: 102 411.01/.03/.1020) 502.0121) 902.01 903.01/.03 920.01 161 Description Volute casing Joint ring Casing wear ring Stud Screw plug Hexagon nut Casing cover
161
20) 21)
Joint ring 411.10 (and 411.15 for versions with mechanical seal) depending on the operating temperature. Order separately in spare parts order. For CPKN-S only.
CPKN
63 of 70
9 Related Documents
Part No.
183
210
230
320.02 322.01 330 330
344
360.01/02
421.01/02 433.01 471.01
452.01 454.01 456.01 458.01 461.01 463.01
Comprising: 411.11/.16/.17 412.0122) 902.02 903.16/.17 920.02 183 901.0424) 930.01 210 920.21 931.01 940.01/.02 230 411.32 412.0620) 320.02 322.01 330 330 360.01/.02 400.01/.02 411.46 421.01/.02 550.23 63825) 672 903.46 914.01/.02 932.01/.02 550.24/.2526) 636.02/.0326) 344 412.0122) 561.02 903.18 902.04 901.31 920.04 411.18 360.01/02 400.01/.02 914.01/.02 421.01/02 433.0123) 471.01 411.1520) 561.03 452.01 454.01 456.01 458.01 461.01 463.01
Description Joint ring O-ring Stud23) Screw plug Hexagon nut Support foot Hexagon head bolt Spring washer Shaft Keywayed nut Lockwasher Key Impeller Joint ring O-ring Angular contact ball bearing Cylindrical roller bearing Bearing bracket Bearing bracket, complete Bearing cover Gasket Joint ring Lip seal Support disc Constant-level oiler Vent plug Screw plug Hexagon socket head cap screw Circlip Disc Lubricating nipple Bearing bracket lantern O-ring Grooved pin Screw plug Stud Hexagon head bolt Hexagon nut Joint ring Bearing cover Gasket Hexagon socket head cap screw Lip seal Mechanical seal, complete Seal cover23) Joint ring Grooved pin Gland follower Stuffing box ring Neck bush Lantern ring Gland packing Drip plate
22) 23) 24) 25) 26)
Not fitted on pump version with conical seal chamber. Not shown in drawing On bearing bracket UP02: socket head cap screw 914.04. Not applicable for grease-lubricated versions On grease-lubricated versions only
64 of 70
CPKN
9 Related Documents
Part No. 502.0121) 507.01 524.01 638 922
Comprising: 502.01 561.01 507.01 524.01 411.32 638 922 411.31
Description Casing wear ring Grooved pin Thrower Shaft protecting sleeve Joint ring Constant-level oiler Impeller nut Joint ring
CPKN
65 of 70
10 EC Declaration of Conformity
10 EC Declaration of Conformity
Manufacturer: KSB Aktiengesellschaft Johann-Klein-Strae 9 67227 Frankenthal (Germany) The manufacturer herewith declares that the product:
CPKN, CPKNO, CPKN-CHs

KSB order number: ...................................................................................................
is in conformity with the provisions of the following Directives as amended from time to time: Pump (set): Machinery Directive 2006/42/EC The manufacturer also declares that the following harmonised international standards have been applied: ISO 12100, EN 809/A1 Applied national technical standards and specifications, in particular: DIN EN ISO 5199 Person authorised to compile the technical file: Name Function Address (company) Address (Street, No.) Address (post or ZIP code, city) (country) The EC Declaration of Conformity was issued in/on:
Place, date
..............................27)............................. Name Function Company Address Address
27)
A signed, legally binding declaration of conformity is supplied with the product.
66 of 70
CPKN
11 Certificate of Decontamination
11 Certificate of Decontamination
Type Order number/ Order item number28) Delivery date Field of application: Fluid pumped28): Please tick where applicable28): ................................................................................................................................ ................................................................................................................................ ................................................................................................................................ ................................................................................................................................ ................................................................................................................................
Radioactive
Explosive
Corrosive
Toxic
Harmful
Bio-hazardous
Highly flammable
Safe
Reason for return28): Comments:
................................................................................................................................ ................................................................................................................................ ................................................................................................................................
The product/accessories have been carefully drained, cleaned and decontaminated inside and outside prior to dispatch/ placing at your disposal. We hereby declare that this product is free from hazardous chemicals, biological or radioactive substances. On seal-less pumps, the rotor has been removed from the pump for cleaning. No special safety precautions are required for further handling. The following safety precautions are required for flushing fluids, fluid residues and disposal: ............................................................................................................................................................... ............................................................................................................................................................... We confirm that the above data and information are correct and complete and that dispatch is effected in accordance with the relevant legal provisions.
.................................................................... Place, date and signature
....................................................... Address
....................................................... Company stamp
28)
Required fields
CPKN
67 of 70
Index
Index
A
Abrasive fluids 40 Auxiliary connections 26
Intended use 8 Interchangeability of pump components 58
K
Keeping the pump warm 36
B
Bearing temperature 44 Bearings 17
L
Leakage rate 37
C
Certificate of decontamination 67 Clearance gaps 44 Commissioning/start-up 32 Constant-level oiler 32 Coupling 44 Coupling alignment 27
M
Mechanical seal 37 Misuse 9 Monitoring equipment 11
N
Name plate 16 Noise characteristics 20
D
Design 16, 19 Designation 16 Direction of rotation 31 Disassembly 49 Disposal 15
O
Oil lubrication Intervals 45 Oil quality 45 Oil quantity 46 Operating limits 8, 39 Order number 6 Ordering spare parts 57 Other applicable documents 6
E
Explosion protection 10, 21, 26, 27, 28, 29, 30, 31, 33, 35, 36, 37, 39, 42, 43, 44, 45
F
Filter 23, 45 Final check 34 Flow rate 40 Frequency of starts 39 Function 19
P
Partly completed machinery 6 Permissible forces and moments at the pump nozzles 24 Piping 23 Preservation 14, 41 Priming and venting 34 Product description 16 Pure graphite packing 37
G
General assembly drawing 62 Gland packing 37 Grease lubrication Grease quality 47 Intervals 47
R
Return to supplier 14 Returning to service 41 Running noises 43, 44
H
Heating 35 Heating speed 36 Heating up 36
S
Safety 8 Safety awareness 9 Scope of supply 20 Servicing/maintenance 42 Shaft seal 17 Shutdown 38, 41 Spare parts stock 58 Start-up 36 Storage 14, 41
I
Impeller type 17 Installation Installation on a foundation 21 Installation without foundation 22 Installation at site 21
68 of 70
CPKN
Index
T
Temperature difference 36 Temperature limits 11 Tightening torques 57 Transport 13
Trouble-shooting 60
W
Water cooling 34
CPKN
69 of 70
KSB Aktiengesellschaft 67225 Frankenthal Johann-Klein-Str. 9 67227 Frankenthal (Germany) Tel. +49 6233 86-0 Fax +49 6233 86-3401 www.ksb.com
2730.8/05-EN (01316128)

KSB CPKN

Uploaded by

Copyright:

Available Formats

KSB CPKN

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

KSB CPKN

Uploaded by

Copyright:

Available Formats

Standardised Chemical Pump

Transport/Temporary Storage/Disposal .............................................13

Description of the Pump (Set) ............................................................16

Installation at Site ...............................................................................21

5.5 5.6 5.7 5.8 5.9

Trouble-shooting ................................................................................60 Related Documents ............................................................................62

EC Declaration of Conformity ............................................................66 Certificate of Decontamination .........................................................67 Index ....................................................................................................68

Back pull-out unit

Suction lift line/suction head line

1.2 Installation of partly completed machinery

1.3 Target group

1.4 Other applicable documents

If agreed to be included in the scope of supply

All the information contained in this section refers to hazardous situations.

2.1 Key to safety symbols/markings

2.3 Intended use

2.4 Personnel qualification and training

2.6 Safety awareness

2.7 Safety information for the operator/user

2.8 Safety information for maintenance, inspection and installation work

2.9 Unauthorised modes of operation

2.10 Explosion protection

Shaft coupling Motor

Depending on the material variant

Fig. 1: Transporting the back pull-out unit

Fig. 2: Transporting the pump

Fig. 3: Transporting the complete pump set

Fig. 4: Transporting the pump on the baseplate

3.4 Return to supplier

4 Description of the Pump (Set)

4 Description of the Pump (Set)

4.3 Name plate

4.4 Design details

4 Description of the Pump (Set)

Cylindrical seal chamber Standardised mechanical seal

Double mechanical seal (back-toback) both sides unbalanced

4 Description of the Pump (Set)

4 Description of the Pump (Set)

4.5 Design and function

4 Description of the Pump (Set)

4.6 Noise characteristics

4.7 Scope of supply

4.8 Dimensions and weights

5.2 Checks to be carried out prior to installation

5.3 Installing the pump set

5.3.1 Installation on the foundation

The foundation has the required strength and characteristics.

5.3.2 Installation without foundation

Re-tighten the locknuts (1, 3) at the levelling elements (4).

5.4.2 Permissible forces and moments at the pump nozzles

The resulting permissible forces have been determined according to:

2000 1500 1000 1150

2750 2100 1400 1450 1100

2750 2100 1400 2000 1500 1000

7350 4700 10000 6700

5700 7400 5700 8000 10450 5700

12000 8000 10000 12800 8000

Fig. 10: Temperature correction diagram 5.4.3 Auxiliary connections

5.6 Checking the coupling alignment

5.7 Aligning the pump and motor